• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.8B
• /
• pp.514-524
• /
• 2005

In optical burst switching(OBS) networks, the ingress edge router assembles packets in the same class queue into the appropriate size of burst. A burst control packet(BCP) is generated for channel reservation of corresponding data burst and sent earlier than the corresponding data burst with an offset time. Offset time is determined considering the number of hops from source to destination and the required quality of service(QoS). After offset time, the burst data is passed through tile pre-configured optical switches without any O/E/O conversion. But a failure in OBS networks may lead to the loss of bursts until the ingress nodes receive the failure indication signal. This results in a significant degradation in QoS. Therefore, in this paper, we propose a fault-tolerant node architecture based on sub-carrier multiplexing to reduce the effects of failure in OBS networks. The Performance of the proposed fault-tolerant node architecture exhibits considerable improvement as compared with the previous ones.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.6B
• /
• pp.331-337
• /
• 2005

The optical Internet is considered as a feasible solution for transporting huge amount of traffic volume in the future Internet. Among optical switching technology for the optical Internet, OBS becomes one of the most promoting solution. Recently, a lebeled OBS(LOBS) architecture is considered for an efficient control on OBS network. Given that a data burst may contain few thousands of IP packets, a single loss of data burst results in a serious throughput degradation in LOBS network. In this paper, we improve the performance of LOBS network by introducing the burst congestion control mechanism. More specifically, the OBS router at the network core detects the network congestion by measuring the loss probability of burst control packet. The OBS router at the network edge reduces the burst generation according to the network condition repored by the OBS router at the network core. Through the simulations, it is shown that the proposed congestion control mechanism can reduce the burst loss probability and improve the LOBS network throughput.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.21-26
• /
• 2008

In this paper, a novel 622Mbps burst-mode clock and data recovery (CDR) circuit is proposed for passive optical network (PON) applications. The CDR circuits are implemented with 0.35um CMOS process technology. Locking dynamics is accomplished with instantaneous feature and data are sampled at an optimal timing. This is realized by seven different delay configurations, which are generated from precisely-controlled delay buffers. The experimental results show that the proposed CDR circuits are operating as expected, recovering an incoming 622Mbps burst-mode input data without errors.

• Journal of the Korean Society of Safety
• /
• v.18 no.4
• /
• pp.16-22
• /
• 2003

Generally the rupture of steam generator tubes proceeds from significant plastic deformation before failure. In this study, the burst pressures of damaged steam generator tubes were calculated from the plastic instability analysis with the finite element method. Two wear types, flat and circumferential types were considered. An equation for the burst pressure was proposed by using the strength reduction factor and the Svensson equation. The analysis results were compared with the experiment data from published references and they showed a good agreement with the experiment data.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.3B
• /
• pp.72-84
• /
• 2005

Optical burst switching networks usually employ one-way reservation by sending a burst control packet with a specific offset time, before transmitting each data burst Same. Due to such a Property, burst-contentions occur when multiple bursts contend for the same wavelength in the same output link simultaneously in a node, leading to burst losses, eventually degrading the quality of service. Therefore, in this paper, we propose a dynamic routing algorithm using minimum local state information in order to decrease burst-contentions. In this proposed scheme, if burst loss rate exceeds a threshold value at a certain node, a new alternative routing path is chosen according to burst priority and location of burst generation, which enables the contending bursts to detour around the congested link. Moreover, for reducing the effect of sending bursts on the primary path due to the alternative path, we also apply a minimum path-cost based routing on link-cost concept. Our simulation results show that proposed scheme improves the network performance in terms of burst loss probability and throughput by comparing with conventional one.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.1B
• /
• pp.109-116
• /
• 2004

Optical Burst Switching (OBS) technology has drawn much attention as a promising solution for IP/WDM networks. OBS has the features such as the offset time, the delayed reservation and the burst assembly. In particular, the burst assembly, which assembles IP packets into the data bursts, has a great impact on the performance of OBS network. In this paper, we compare the performance of three different burst assembly schemes and investigate their impact on the performance of OBS network.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.1
• /
• pp.203-210
• /
• 2002

The transmission pipeline industry spends many millions of dollars annually performing inline inspections, excavating sites of possible corrosion, and repairing or replacing damaged sections of pipe. New criteria fur evaluation of the integrity of corroded pipe have been developed in recent years to help in controlling these costs. These new criteria vary widely in their estimates of integrity and the most appropriate criterion fur a given pipeline is net always clear. This paper presents an overview, comparison and evaluation of acceptability criteria for corrosion deflects in pipelines. By full scale burst tests, this paper has assessed the relative accuracy of each of theses criteria in predicting burst pressure. Many of the criteria appear to be excessively conservative and indicate that deflects must be repaired when none is needed, based upon burst test data.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.12B
• /
• pp.1037-1043
• /
• 2006

There has been proposed an algorithm to reduce data burst processing delay in group scheduling in core nodes of optical burst switching networks. Since, in this algorithm, look-up tables containing all the void time information in scheduling windows are generated as soon as the primary group scheduling session terminates, it becomes faster to reassign dropped data bursts to proper voids in different data channels by referring to the tables. The group scheduling with this algorithm showed almost the same channel utilization as the one without using the algorithm but performed a little better in both burst loss probability and wavelength conversion rate. On the other hand, per-burst processing time has been reduced dramatically in the load region of higher than 0.8, showing a factor of 2.1 reduction at 0.9.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.858-864
• /
• 2019

A clock system is proposed to eliminate data loss due to frequency difference between sensor nodes in a sensor utility network. The proposed clock system for each sensor node consists of a bust clock-data recovery (CDR) circuit, a digital phase-locked loop outputting a 32-phase clock, and a digital frequency synthesizer using a programmable open-loop fractional divider. A CMOS oscillator using an active inductor is used instead of a burst CDR circuit for the first sensor node. The proposed clock system is designed by using a 65 nm CMOS process with a 1.2 V supply voltage. When the frequency error between the sensor nodes is 1%, the proposed burst CDR has a time jitter of only 4.95 ns with a frequency multiplied by 64 for a data rate of 5 Mbps as the reference clock. Furthermore, the frequency change of the designed digital frequency synthesizer is performed within one period of the output clock in the frequency range of 100 kHz to 320 MHz.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.72-73
• /
• 2003

In volume holographic memory (VHM), two-dimensional data array (i.e. data page) is used for the recording and the retrieving process with the aid of spatial light modulator (SLM) and CCD camera. Due to this two-dimensional parallel data processing, burst errors in this system also have two-dimensional characteristics in a data page domain. In this paper, we present a channel model of the burst noise and burst error for the VHM system using disk type recording media. (omitted)