• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.15 no.4
• /
• pp.269-274
• /
• 1993

This is the case report of huge complex odontoma treated with sagittal splitting of buccal bone plate and iliac bone graft in left mandible angle. The 22 years old patient was admitted to the department of Oral and Maxillofacial Surgery of Kyungpook National University Hospital with the chief complaint of swelling on the left mandible angle area. We used extra oral Risdon incision and splitted the buccal cortical bone after making the horizontal bone cut buccally. The tumor mass was removed with cutting into the pieces with surgical bur to prevent mandibular fracture. The dead space was grafted with autogenous iliac bone graft and the splitted buccal cortical bone was fixed with two L-type miniplate. After 12months follow up check, we noticed good process of bone healing and satisfactory aesthetic result. In this case, my operative approach provided the excellent surgical access to the hard tissue mass and minimized post operative complication comparing with the conventional surgical approaches.

• Nuclear Engineering and Technology
• /
• v.52 no.9
• /
• pp.2072-2077
• /
• 2020

The purpose of this study was to demonstrate the feasibility of sensing changes in a tumor during boron neutron capture therapy (BNCT) using a Monte Carlo simulation tool. In the simulation, an epi-thermal neutron source and a water phantom including boron uptake regions (BURs) were simulated. Moreover, this simulation also included a detector for positron emission tomography (PET) scanning and an adaptively-designed collimator (ADC) for PET. After the PET scanning of the water phantom, including the 511 keV source in the BUR, the ADC was positioned in the PET's gantry. Single prompt gamma rays were collected through the ADC during neutron irradiation. Then, single prompt gamma ray-based tomography images of different sized tumors were acquired by a four-step process. Both the signal-to-noise ratio (SNR) and tumor size were analyzed from each step image. From this analysis, we identified a decreasing trend of both the SNR and signal intensity as the tumor size decreased, which was confirmed in all images. In conclusion, we confirmed the feasibility of sensing changes in a tumor during BNCT using PET and an ADC through Monte Carlo simulation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.248-248
• /
• 2009

Recently, the control of size, morphology and dimensionality in inorganic materials has been rapidly developed into a promising field in materials chemistry. 3D nanostructured flower-like ZnO architecture with different size and shapes have been simply synthesized via a hydrothermal process, using zinc acetate and ammonium hydroxide as reactants.[1] In this study, the Zno thin-films were deposited by RF magnetron sputtering in other to get high adhesion and uniformity of 3D nanostructured flower-like ZnO architecture on a $SiO_2$ substrate. The XRD patterns identified that the obtained the nanocrystallized ZnO architecture exhibited a wurtzite structure. SEM images illustrated that the flower-like ZnO bundles consisted of flower-like or chestnut bur, which were characterized by polycrystalline and [0001] preferential orientation.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.11
• /
• pp.124-135
• /
• 1994

In this paper, we propose a Korean syntax analysis system for special syntax processing. HPSG, which processes syntatic and semantic analysis unificationally, is chosen for grammar description. Head-driven unidirectional active chart parser, which is efficient in Korean processing, is used for parsing mechanism. The parser of this paper can analyze not only general sentence structure which consists of complement-head, adjunct-head and head-head structure bur also special syntax which consists of auxiliay verb sentence, causative sentence, passive sentence and so on.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.32 no.6
• /
• pp.567-572
• /
• 2010

Intraoperative breakage of instruments can be occurred unexpectedly. To prevent damage of neighboring important anatomic structures and consequent complications, broken instruments should be removed as soon as possible. There have been several methods to remove broken instruments. One of them is the Carm fluoroscopy which is commonly used for locating metal foreign bodies. However, its application for removal of broken instruments in the oral and maxillofacial area is not common. In our experiences with the removal of two broken instruments in mandibular area, the newly developed dental mini C-arm was used to find broken instrument in soft tissue, because it gives real-time in situ information for the intraoperative location. We report two cases with broken instruments, a broken dental needle in the pterygomandibular space and a broken straight bur in the mandibular angle area. They were identified and could be removed safely using a dental mini C-arm.

• The Journal of Advanced Prosthodontics
• /
• v.7 no.3
• /
• pp.249-256
• /
• 2015

PURPOSE. The aim of this study was to evaluate the effects of atmospheric plasma (APL) versus conventional surface treatments on the adhesion of self-adhesive resin cement to Ti-6Al-4V alloy. MATERIALS AND METHODS. Sixty plates of machined titanium (Ti) discs were divided into five groups (n=12): 1) Untreated (CNT); 2) Sandblasted (SAB); 3) Tribochemically treated (ROC); 4) Tungsten CarbideBur (TCB); 5) APL treated (APL). SEM analysis and surface roughness (Ra) measurements were performed. Self-adhesive resin cement was bonded to the Ti surfaces and shear bond strength (SBS) tests, Ra and failure mode examinations were carried out. Data were analyzed by one-way analysis of variance and chi-squared test. RESULTS. The lowest SBS value was obtained with CNT and was significantly different from all other groups except for APL. The ROC showed the highest SBS and Ra values of all the groups. CONCLUSION. It was concluded that the effect of APL on SBS and Ra was not sufficient and it may not be a potential for promoting adhesion to titanium.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.30 no.6
• /
• pp.551-553
• /
• 2004

The displacement of an entire tooth into the adjacent anatomical area is an uncommon complication of a tooth extraction. We encountered a 23-year-old woman who had previously undergone surgery under local anesthesia to remove the lower third molar about 12 weeks prior and the upper third molar was extracted 2 days prior to visiting this hospital. Upon admission, she complained of a swallowing discomfort and a mouth opening limitation. Panoramic radiograph and a CT scan revealed a displacement of the entire tooth into the lateral pharyngeal space. The tooth was retrieved via the transoral approach under general anesthesia. The removed tooth had an indentation formed by a dental bur. Therefore, it was concluded that the tooth displaced into the lateral pharyngeal space was the lower third molar. This report describes an unusual case of a third molar that was displaced into the lateral pharyngeal space with a review of the relevant literature.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.71-71
• /
• 2003

Hot embossing has been widely accepted as an alternative to photolithography in generating patterns on polymeric substrates. The optimization of embossing process should be accomplished based on polymer substrate materials. In this paper, the effect of polymer substrates on nano scale hot embossing process was studied. Silicon molds with nano size patterns were fabricated by e-beam direct writing. Molds were coated with self-assembled monolayer (SAM) of (1, 1, 2.2H -perfluorooctyl)-trichlorosilane to reduce the stiction between mold and substrates. For an embossing, pressure of 55, 75 bur, embossing time of 5 min and temperature of above transition temperature were peformed. Polymethylmethacrylates (PMMA) with different molecular weights of 450,000 and 950,000, MR-I 8010 polymer (Micro Resist Technology) and polyaliphatic imide copolymer were applied for hot embossing process development in nano size. These polymers were spun coated on the Si wafer with the thickness between 150 and 200 nm. The nano size patterns obtained after hot embossing were observed and compared based on the polymer properties by scanning electron microscopy (SEM). The imprinting uniformity dependent on the Pattern density and size was investigated. Four polymers have been evaluated for the nanoimprint By optimizing the process parameters, the four polymers lead to uniform imprint and good pattern profiles. A reduction in the friction for smooth surfaces during demoulding is possible by polymer selection.

• The Korean Journal of Ecology
• /
• v.19 no.6
• /
• pp.507-517
• /
• 1996

To explain the horizontal expansion of a rhizomatous perennial, Convallaria keiskei(lily-of-the-valley), in a study site of Chunchon, Kangwon Province, Korea, ramet growth and clonal structure were studied. Remarkable growth stategies were clarified. First, the timing for the successive phenological events such as sprouting. flowering and rhizome growth for lily-of-the-valley was fitted to exploit early spring when the canopy of overstory was opened. Second, these events were supported by effective matter allocation pattern: for example, two-year investment for new rhizomes enabled the first year ramets to mature in six weeks after sprouting and to grow up to 85% of the leaf area of perennial ramets. Finally, the ramet population was increased by local disturbances such as freezing, herbivory and collection by human. The rule that a clone was supposed to produce one new thizome per year was broken by occasional disturbances. Then, up to 5rhizomes from latent bur could be redeveloped. Based on clonal structure, 80% or total clones have from 1 to 4 ramets. this means there have occurred minor disturbances. Therefore, in conclusion, the successful flourishing of lily-of-the-valley came from its effective frowth strategy to take advantage of site disturbance.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.2
• /
• pp.132-137
• /
• 2018

PURPOSE. The purpose of this study was to evaluate and compare three polishing systems on the surface roughness and phase transformation of monolithic zirconia. MATERIALS AND METHODS. 100 disk shaped specimens (10 mm diameter, 3 mm thickness) were fabricated from monolithic zirconia blocks. 20 specimens were left as a control group and remaining specimens were grinded by diamond bur to simulate the occlusal adjustments. Grinded specimens were randomly divided into 4 groups: group G (no polishing), group M (Meisinger, zirconia polishing kit), group E (EVE Diacera, zirconia polishing kit), and group P (EVE Diapol, porcelain polishing kit). Surface roughness was measured with profilometer and surface topography was observed with SEM. XRD analysis was performed to investigate the phase transformation. Statistical analysis was performed with one-way ANOVA and Tukey's post hoc tests at a significance level of P=.05. RESULTS. All polishing groups showed a smoother surface than group G. Among 3 polishing systems, group M and group E exhibited a smoother surface than the group P. However, no significant differences were observed between group M and group E (P>.05). Grinding and polishing did not cause phase transformations in zirconia specimens. CONCLUSION. Zirconia polishing systems created a smoother surface on zirconia than the porcelain polishing system. Phase transformation did not occur during the polishing procedure.