• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.2
• /
• pp.157-178
• /
• 2001

In this paper, the nonlinear control of high precision pointing stabilization system using feedback-linearization design methodology based on system parameter identification is discussed. Modern nonlinear servomechanism theory is adapted to cope with the hard nonlinearities inherent in the turret system. The mathematical models of electrical turret driving system to develop a high performance control algorithm are derived, and the parameter estimation algorithm identifying the unknown system parameters such as vicious and coulomb frictions, stiffness and inertia is developed. Through computer simulation and experiments, it is shown that pointing and tracking accuracy and stabilization against the wideband stochastic disturbance induced by vehicle running on the bump course are improved. Therefore, it is considered the proposed nonlinear control technique is effective in counteracting the nonlinearities and disturbances.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.1037-1040
• /
• 1998

In this research a fault-tolerant and bumpless switching control is proposed for boiler systems used in the power plants. Firstly, three operating points are selected to control the nonlinear boiler through the full operational range, and the $H_{\infty}$ loop shaping controller and the model-based predictive controller(MBPC) are designed. To prevent the windup and bump problems which are caused by the actuator saturation and the controller switching, an anti-windup and bumpless transfer technique is adopted to the $H_{\infty}$ loop shaping controller. Also the constrained gain-scheduling technique is applied to MBPC to achieve the same objective. Secondly, the fault-tolerant control technique is proposed to continue the control action without stopping the boiler operation even in case of some faults. Through various simulation studies, the performances of the proposed control techniques are demonstrated.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.1 no.1
• /
• pp.65-81
• /
• 1998

Objective technology development has been carried out aiming performance improvement of the stabilized gun-pointing system for Type-4 tank. The full nonlinear simulation programs with gun bending modes and nonlinearities were developed to estimate, analyze and design the driving and stabilization system, and validated through the comparisons between simulations and test results of the existing Type-1 tank. The prototype is designed, fabricated, tested and evaluated on the test range as well as in the laboratory and followed by development and operational tests. The performance test results on stationary and on-the-move conditions are turned out to be superior to those of the advanced tanks developed in foreign countries.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.129.2-129
• /
• 2001

Visual effects are important cues for providing occupant s with virtual reality in a vehicle simulator which imitates real driving. The viewpoint of an occupant is sensitively dependent upon the occupant´s posture, therefore, the total body motion must be considered in a graphic simulator. A real time simulation is required for the dynamic analysis of complex human body motion. This study attempts to apply a neural network to the motion analysis in various driving situations. A full car of medium-sized vehicles was selected and modeled, and then analyzed using ADAMS in such driving conditions as bump-pass and acceleration. A multibody system analysis software, MADYMO, was used in the motion analysis of an adult male dummy in the seated position. Position data of the head were collected as inputs to the viewpoint movement. Based on these data, a back- propagation neural network was ...

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.2
• /
• pp.162-169
• /
• 2008

Compliance effect consideration method for real-time multibody vehicle dynamics is proposed using quasi-static analysis. The multibody vehicle model without bush elements is used based on the subsystem synthesis method which provides real-time computation on the multibody vehicle model. Reaction forces are computed in the suspension subsystem. According to deformation from the quasi-static analysis using reaction forces and bush stiffness, suspension hardpoint locations and suspension linkage orientation are changed. To validate the proposed method, quarter car simulations of McPherson strut and multilink suspension subsystems are performed. Full car bump run simulations and fish hook handling test simulations are also carried out comparing with the ADAMS vehicle model with bush elements. CPU times are also measured to see the real-time capabilities of the proposed method.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.971-976
• /
• 1996

A flexible pointing system mounted on top of a vehicle suffers from performance degradation due to bending vibrations as the vehicle runs on a bump course. In order to improve the pointing performance, the pointing structure's vibrations should be suppressed. In this paper, a nonlinear controller is designed to control the tip position of the pointing system while actively suppressing the vibrations. To cope with high order dynamics and nonlinearities of the plant and hydraulic actuating system, a two-stage sliding mode controller is devised. The desired actuating pressure is obtained in the first stage and then the in put current In the hydraulic servo system is computed to generate the pressure. The simulation results show the effectiveness of this scheme and improvements in pointing accuracy.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.132-140
• /
• 2002

A momentum backpropagation neural network is prepared to carry out real-time dynamics simulations of a passenger car. A full-car model of fifteen degrees of freedom was constructed for vehicle dynamics analysis. Human body dynamics analysis was performed for a male driver(50 percentile Korean adult) restrained by a three point seatbelt system. The trained data using the neural network were obtained using a dynamic solver, ADAMS . The neural network were formed based on the dynamics of the simulator. The optimized hidden layer was obtained by selecting the optimal number of hidden layers. The driving scenario including bump passing and lane changing has been used for the estimation of the proposed neural network. A comparison between the trained data and neural network outputs is found to be satisfactory to show the applicability of the suggested approach.

• ETRI Journal
• /
• v.36 no.4
• /
• pp.643-653
• /
• 2014

To reduce interconnect delay and power consumption while improving chip performance, a three-dimensional integrated circuit (3D IC) has been developed with die-stacking and through-silicon via (TSV) techniques. The power supply problem is one of the essential challenges in 3D IC design because IR-drop caused by insufficient supply voltage in a 3D chip reduces the chip performance. In particular, power bumps and TSVs are placed to minimize IR-drop in a 3D power delivery network. In this paper, we propose a design methodology for 3D power delivery networks to minimize the number of power bumps and TSVs with optimum mesh structure and distribute voltage variation more uniformly by shifting the locations of power bumps and TSVs while satisfying IR-drop constraint. Simulation results show that our method can reduce the voltage variation by 29.7% on average while reducing the number of power bumps and TSVs by 76.2% and 15.4%, respectively.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.3
• /
• pp.251-257
• /
• 2012

Unmanned ground vehicles have important military, reconnaissance, and materials handling application. Many of these applications require the UGVs to move at high speeds through uneven, natural terrain with various compositions and physical parameters. This paper presents a framework for high speed autonomous navigation based on the integrated real time traversability. Specifically, the proposed system performs real-time dynamic simulation and calculate maximum traversing velocity guaranteeing safe motion over rough terrain. The architecture of autonomous navigation is firstly presented for high-speed autonomous navigation. Then, the integrated real time traversability, which is composed of initial velocity profiling step, dynamic analysis step, road classification step and stable velocity profiling step, is introduced. Experimental results are presented that demonstrate the method for a $6{\times}6$ autonomous vehicle moving on flat terrain with bump.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.369-372
• /
• 1998

In this research a fault-tolerant and bumpless switching control is proposed for boiler systems used in the power plants. Firstly, three operating points are selected to control the nonlinear boiler through the full operational range, and the $H_{\infty}$ loop shaping controller and the model-based predictive controller(MBPC) are designed. To prevent the windup and bump problems which are caused by the actuator saturation and the controller switching, an anti-windup and bumpless transfer technique is adopted to the $H_{\infty}$ loop shaping controller. Also the constrained gain-scheduling technique is applied to MBPC to achieve the same objective. Secondly, the fault-tolerant control technique is proposed to continue the control action without stopping the boiler operation even in case of some faults. Through various simulation studies, the performances of the proposed control techniques are demonstrated.