• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.5
• /
• pp.1167-1174
• /
• 2024

The purpose of this study was to evaluate the effects of various layer thicknesses and build angles on the flexural strength and surface roughness of repaired 3D-printed denture base resin. 3D-printed bar-shaped specimens with a 45° bevel were fabricated according to layer thickness(50 ㎛ and 100 ㎛) and build angle(0-degree, 45-degree, and 90-degree). Denture relining resin was applied to the 2 mm repair area Flexural strength was measured by a three-point bending test using a universal testing machine, and surface roughness(Ra) and surface topography were observed using a digital optical microscope at ×500 magnification. Statistical significance was analyzed using two-way ANOVA, one-way ANOVA, and Games-Howell post hoc(α = .05). Except for the 90-degree group, the group with a layer thickness of 100 ㎛ showed better flexural strength values than the group with a layer thickness of 50 ㎛(p < .05). Additionally, within the same layer thickness, the 45-degree group showed the lowest flexural strength value. The Ra values of the 0-degree and 90-degree groups, where the build angle was 45° to the layer orientation, were higher at 100 ㎛ than at 5 0 ㎛ layer thickness(p < .05), and the Ra value of the 45-degree group, where the build angle was parallel to the layer orientation, was lower than those of other build angles(p < .05). Layer thickness and build angle significantly affected the surface roughness of 3D-printed denture base resin, and the surface roughness was confirmed to be closely related to the bonding strength with denture relining resin.

• The Journal of the Korean dental association
• /
• v.58 no.1
• /
• pp.19-26
• /
• 2019

Purpose: The purpose of this study is to compare the adhesion of Candida albicans according to build angle in 3D printing denture base resin. Methods: The 3D printing was performed by setting the build angle of the disk type specimen designed by CAD program at 0 degree, 30 degrees, 60 degrees, and 90 degrees. Surface roughness was measured using a non-contact 3D microsurface profiler. The specimens were incubated in Candida albicans suspension for 24 hours. The attached Candida albicans were detached by cell scraper. The suspension of detached C. albicans was serially diluted and plated on Trypticase soy broth. After 48 hours of incubation, total colony forming unit was counted. Results: There was no significant difference in surface roughness(Sa) between the test groups, but the interlayer boundary was observed. There was no statistically significant difference in total colony forming units of Candida albicans between the test groups. Conclusion: There was no difference in the average surface roughness and adhesion of Candida albicans between the specimens. It is considered that the setting of the build angle should be set considering the accuracy or strength rather than the roughness of the surface.

• The Journal of Advanced Prosthodontics
• /
• v.14 no.3
• /
• pp.150-161
• /
• 2022

PURPOSE. The purpose of the study was to assess the influence of build orientations and density of support structures on the trueness of the 3D printed removable partial denture (RPD) frameworks. MATERIALS AND METHODS. A maxillary Kennedy class III and mandibular class I casts were 3D scanned and used to design and produce two 3D virtual models of RPD frameworks. Using digital light processing (DLP) 3D printing, 47 RPD frameworks were fabricated at 3 different build orientations (100, 135 and 150-degree angles) and 2 support structure densities. All frameworks were scanned and 3D compared to the original virtual RPD models by metrology software to check 3D deviations quantitatively and qualitatively. The accuracy data were statistically analyzed using one-way ANOVA for build orientation comparison and independent sample t-test for structure density comparison at (α = .05). Points study analysis targeting RPD components and representative color maps were also studied. RESULTS. The build orientation of 135-degree angle of the maxillary frameworks showed the lowest deviation at the clasp arms of tooth 26 of the 135-degree angle group. The mandibular frameworks with 150-degree angle build orientation showed the least deviation at the rest on tooth 44 and the arm of the I-bar clasp of tooth 45. No significant difference was seen between different support structure densities. CONCLUSION. Build orientation had an influence on the accuracy of the frameworks, especially at a 135-degree angle of maxillary design and 150-degree of mandibular design. The difference in the support's density structure revealed no considerable effect on the accuracy.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.232-232
• /
• 2000

switched reluctance motors and drives are increasingly used in industrial applications due to their robust mechanical structure, low inertia and reduction in the rotor losses. As the motor speed increase turn on angle must be advanced to build up phase current. When C-dump converter is applied to switched reluctance motor, the capacitance of dump C has to have proper value. In this paper advance angle for a switched reluctance motor and capacitance of dump C are investigated. Then proper advance angle and the capacitance of dump-C are propose for the industrial low voltage SR motor.

• The Journal of Advanced Prosthodontics
• /
• v.12 no.4
• /
• pp.225-232
• /
• 2020

PURPOSE. This study aimed to fabricate provisional crowns at varying build directions using the digital light processing (DLP)-based 3D printing and evaluate the marginal and internal fit of the provisional crowns using the silicone replica technique (SRT). MATERIALS AND METHODS. The prepared resin tooth was scanned and a single crown was designed using computer-aided design (CAD) software. Provisional crowns were printed using a DLP-based 3D printer at 6 directions (120°, 135°, 150°, 180°, 210°, 225°) with 10 crowns in each direction. In total, sixty crowns were printed. To measure the marginal and internal fit, a silicone replica was fabricated and the thickness of the silicone impression material was measured using a digital microscope. Sixteen reference points were set and divided into the following 4 groups: marginal gap (MG), cervical gap (CG), axial gap (AG), and occlusal gap (OG). The measurements were statistically analyzed using one-way ANOVA and Dunnett T3. RESULTS. MG, CG, and OG were significantly different by build angle groups (P<.05). The MG and CG were significantly larger in the 120° group than in other groups. OG was the smallest in the 150° and 180° and the largest in the 120° and 135° groups. CONCLUSION. The marginal and internal fit of the 3D-printed provisional crowns can vary depending on the build angle and the best fit was achieved with build angles of 150° and 180°.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.3
• /
• pp.243-250
• /
• 2012

This paper proposes a 3D map-building algorithm using one LRF (Laser Range Finder) while a mobile robot is navigating on the slanted surface. There are several researches on 3D map buildings using the LRF. However most of them are performing the map building only on the flat surface. While a mobile robot is moving on the slanted surface, the view angle of LRF is dynamically changing, which makes it very difficult to build the 3D map using encoder data. To cope with this dynamic change of the view angle in build 3D map, IMU and balance filters are fused to correct the unstable encoder data in this research. Through the real navigation experiments, it is verified that the fusion of multiple sensors are properly performed to correct the slope angle of the slanted surface. The effectiveness of the balance filter are also checked through the hill climbing navigations.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.12
• /
• pp.25-31
• /
• 2018

Selective Laser Melting is one of the representative 3D printing techniques for handling metal materials. The main factors influencing the characteristics of structures fabricated by the SLM method include the build-up angle of structures, laser power, laser scan speed, and scan spacing. In this study, the tensile properties of AlSi10Mg alloys were investigated by considering the build-up angle of tensile test specimens, laser scanning speed and scan spacing as variables. The yield stress, tensile strength, and elongation were considered as tensile properties. From the test results, it was confirmed that the yield stress values were lowered in the order of 0, 45, and 90 based on the manufacturing direction of the tensile specimen. The maximum yield stress value was obtained at 1870 mm / min based on the laser scan speed. The yield stress size decreased with decreasing scan speed. Based on the laser scan spacing, as the value increases, the yield stress increases, but the variation is smaller than the other test criteria. The tendency of the tensile strength and elongation variation depending on the test conditions was difficult to understand.

• Journal of Korean Association for Spatial Structures
• /
• v.14 no.1
• /
• pp.69-76
• /
• 2014

When we excavate an underground to build basement, the ground anchors are needed to prevent collapse of neighboring ground, subsidence and movement. Ground anchor construction required shore sheet piles, wales and struts as to maintain secure excavation. Existing box-type bracket using head part of ground anchor can not be possibly adjustable to the boring angle because the brackets are manufactured with unified angle in a factory. Also, box-type brackets have imperfection and instability caused by inequable force. In this study, a new bracket system is proposed. The bracket's side plate is reinforced and the angle of boring can be controlled. To investigate the structural performance of presented brackets, FEM analysis has been performed by using ANSYS commercial program. As a result, this bracket shows sufficient stability for all angle case and the strength is increased about 24% than existing bracket.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.133-134
• /
• 2009

We have presented our approach to build a 3D display system based on digital holography. For wide viewing angle, we have presented several techniques such as measurement, time-sharing display, and coherent amplification. These techniques can advance the wavefront 3D display system to next stage.

• Steel and Composite Structures
• /
• v.51 no.4
• /
• pp.417-440
• /
• 2024

Artificial neural networks (ANN) have been the focus of several studies when it comes to evaluating the pile's bearing capacity. Nonetheless, the principal drawbacks of employing this method are the sluggish rate of convergence and the constraints of ANN in locating global minima. The current work aimed to build four ANN-based prediction models enhanced with methods from the black hole algorithm (BHA), league championship algorithm (LCA), shuffled complex evolution (SCE), and symbiotic organisms search (SOS) to estimate the carrying capacity of piles in cold climates. To provide the crucial dataset required to build the model, fifty-eight concrete pile experiments were conducted. The pile geometrical properties, internal friction angle 𝛗 shaft, internal friction angle 𝛗 tip, pile length, pile area, and vertical effective stress were established as the network inputs, and the BHA, LCA, SCE, and SOS-based ANN models were set up to provide the pile bearing capacity as the output. Following a sensitivity analysis to determine the optimal BHA, LCA, SCE, and SOS parameters and a train and test procedure to determine the optimal network architecture or the number of hidden nodes, the best prediction approach was selected. The outcomes show a good agreement between the measured bearing capabilities and the pile bearing capacities forecasted by SCE-MLP. The testing dataset's respective mean square error and coefficient of determination, which are 0.91846 and 391.1539, indicate that using the SCE-MLP approach as a practical, efficient, and highly reliable technique to forecast the pile's bearing capacity is advantageous.