• Journal of electromagnetic engineering and science
• /
• 제16권1호
• /
• pp.52-56
• /
• 2016

This paper suggests a class-F power amplifier with split open-end stubs to provide a broadband high-efficiency operation. These stubs are designed to have wide bandwidth by splitting wide open-end stubs into narrower stubs connected in shunt in an output matching network for class-F operation. In contrast to conventional wideband class-F designs, which theoretically need a large number of matching lines, this method requires fewer transmission lines, resulting in a compact circuit implementation. In addition, the open-end stubs are designed with slant ends to achieve additional wide bandwidth. To verify the suggested design, a 10-W class-F power amplifier operating at 1.7 GHz was implemented using a commercial GaN transistor. The measurement results showed a peak drain efficiency of 82.1% and 750 MHz of bandwidth for an efficiency higher than 63%. Additionally, the maximum output power was 14.45 W at 1.7 GHz.

• 대한전자공학회논문지
• /
• 제27권9호
• /
• pp.1344-1350
• /
• 1990

A design method of ultra-broadband microwave amplifier is presented. A lossy network is represented as the combination of a serial impedance component and a parallel admittance component, and the realizable ranges of the gain and the reflection coefficients are derived with the components connected to the input, output or interstage network. The matching network has been designed by using the serial and parallel immittance loci which have the constant gain or reflection coefficients within the realizable ranges. Using the proposed method, deisgn examples of ultra-broadband amplifiers operating from dc to 12GHz frequency range are presented.

• ETRI Journal
• /
• 제36권1호
• /
• pp.116-123
• /
• 2014

In this paper, a novel unequal broadband out-of-phase power divider (PD) is presented. Double-sided parallel-strip lines (DSPSLs) are employed to achieve an out-of-phase response. Also, an asymmetric dual-band matching structure with two external isolation resistors is utilized to obtain arbitrary unequal power division, in which the resistors are directly grounded for heat sinking. A through ground via (TGV), connecting the top and bottom sides of the DSPSLs, is used to short the isolation components. Additionally, this property can efficiently improve the broadband matching and isolation bandwidths. To investigate the proposed divider in detail, a set of design equations are derived based on the circuit theory and transmission line theory. The theoretical analysis shows that broadband responses can be obtained as proper frequency ratios are adopted. To verify the proposed concept, a sample divider with a power division of 2:1 is demonstrated. The measured results exhibit a broad bandwidth from 1.19 GHz to 2.19 GHz (59.2%) with a return loss better than 10 dB and port isolation of 18 dB.

• ETRI Journal
• /
• 제39권1호
• /
• pp.51-61
• /
• 2017

This paper demonstrates a systematic approach for the design of broadband, high efficiency, high power, Class-AB RF amplifiers with high gain flatness. It is usually difficult to simultaneously achieve a high gain flatness and high efficiency in a broadband RF power amplifier, especially in a high power design. As a result, the use of a computer-aided simulation is most often the best way to achieve these goals; however, an appropriate initial value and a systematic approach are necessary for the simulation results to rapidly converge. These objectives can be accomplished with a minimum of trial and error through the following techniques. First, signal gain variations are reduced over a wide bandwidth using a proper pre-matching network. Then, the source and load impedances are satisfactorily obtained from small-signal and load-pull simulations, respectively. Finally, two high-order Chebyshev low-pass filters are employed to provide optimum input and output impedance matching networks over a bandwidth of 100 MHz-500 MHz. By using an EM simulation for the substrate, the simulation results were observed to be in close agreement with the measured results.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권4호
• /
• pp.483-490
• /
• 2011

본 논문에서는 주기적 접지구조(PAGS)를 이용하여 실리콘 RFIC 반도체 기판상에 다단 임피던 스변환기를 제작 평가하였다. 제작된 임피던스변환기의 면적은 종래의 약 8.7 %인 0.026 $mm^2$이며, 8 ~ 49.5 GHz의 범위에서 양호한 RF특성을 보여주었다.

• 한국수산과학회지
• /
• 제50권5호
• /
• pp.605-615
• /
• 2017

A multi-resonant broadband acoustic transducer with six Tonpilz elements operating at different resonant frequencies in a transducer assembly was fabricated, tested, and analyzed. A compensated transducer, modified by adding series inductance to the developed multi-resonant broadband transducer, was shown to provide improved bandwidth performance with a relatively more uniform frequency response compared with the uncompensated transducer. By controlling the series inductance, flat frequency response characteristics at two frequency bands were obtained over the range 38-52 kHz with 1.1 mH inductance and 50-60 kHz with 0.4 mH inductance. These results suggest that the operating frequency of the developed multi-resonant broadband transducer in a chirp echo sounder can be shifted to a different frequency band that is optimized according to the environment for more effective echo surveys of fishing grounds.

• 한국전자파학회논문지
• /
• 제23권1호
• /
• pp.122-130
• /
• 2012

본 논문에서는 무선 인터넷 서비스 이용을 위한 WiBro 대역(2.3~2.4 GHz) 차량용 광대역 안테나를 개발하였다. 개발된 안테나의 급전부는 T-정합 방식을 응용한 다단 구조의 병렬 T-정합 방식을 이용하여 광대역 특성을 가질 수 있게 하였으며, 각각의 T-정합 회로는 비아-홀을 이용하여 연결하였다. 성능 검증을 위해서 설계된 안테나를 상용 세단의 후면 유리에 장착 후 반사 손실과 안테나 이득을 측정하였으며, 강전계와 약전계에서의 수신성능 필드 테스트를 수행하였다. 측정 결과, 제안된 안테나는 WiBro 대역에서 300 MHz($S_{11}$ <10 dB, 2.296~2.596 GHz)의 대역폭을 가지며, azimuth 방향에서 평균 -5.13 dBi의 안테나 이득을 보였다.

• 비파괴검사학회지
• /
• 제37권1호
• /
• pp.37-43
• /
• 2017

초음파탐상법을 이용하여 마이크로미터의 크기 작은 결함을 검출하기 위해서는 높은 공진주파수와 큰 분해능의 초음파 변환기가 필요하다. 초음파 변환기의 공진주파수와 분해능은 변환기에 사용된 압전소자의 두께, 후면재 및 탐상 시스템 간의 전기 임피던스 정합과 밀접한 관련이 있으며, 이 중 전기 임피던스 매칭은 초음파 변환기와 초음파탐상 시스템 사이의 서로 다른 입 출력단을 연결하는 과정에서, 두 연결단의 전기적 임피던스 차이에 의한 에너지 반사와 손실을 줄이는 중요한 역할을 한다. 임피던스 정합에서 흔히 많이 사용하는 방법은 LC-정합회로이다. 이러한 LC-정합을 통해 탐상 시스템과 초음파 변환기의 전기 임피던스를 $50{\Omega}$으로 맞추어 두 연결단 사이의 임피던스 차이를 보정해 줌으로서 초음파 변환기에서 발생되는 전기신호의 손실을 줄 수 있다. 본 연구에서는 15 MHz의 공진주파수를 가지는 광대역 수침형 초음파 탐촉자를 제작하고 광대역 특성을 갖는 초음파 변환기를 위한 LC 임피던스 정합법을 적용하였다.

• 전기전자학회논문지
• /
• 제26권3호
• /
• pp.456-461
• /
• 2022

본 논문에서는 차동 증폭기에 필수적으로 필요한 Radio frequency(RF) transformer(TF)을 활용하여 광대역 이득 특성을 가지는 2단 단일 종단 전력증폭기를 제시하였다. RF TF의 특징을 파악하고 광대역 특성을 가지도록 설계한 뒤 2단 전력증폭기의 단간(inter-stage) 임피던스 정합 회로에 적용함으로써 증폭기의 대역폭을 향상시킬 수 있다. 기존의 2단 단일 종단(Single-ended) 증폭기의 성능과 면적을 유지하면서 광대역 이득 특성을 얻을 수 있도록 단간 정합 회로를 Monolithic Microwave Integrated Circuit (MMIC)와 다층 PCB에 구현하고 시뮬레이션을 통해 결과를 비교하였다. InGaP/GaAs HBT 모델을 사용하여 설계한 2단 전력증폭기 모듈을 시뮬레이션 한 결과 중심주파수 3.3GHz에서 기존의 전력증폭기가 11.2%의 fractional 대역폭을 보인 반면 제안된 설계 기법을 적용한 전력증폭기는 19.8%의 개선된 대역폭을 가짐을 확인하였다.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제4C권6호
• /
• pp.263-267
• /
• 2004

A new type of interaction circuitry for a broadband gyro-TWT is presented in this paper. A method for the analysis of dispersion characteristics of a periodic structure, which is composed of conducting posts in a rectangular waveguide, is presented. This method utilizes a mode matching technique and equivalent circuit model. The calculated and measured results demonstrate that this periodic structure could be utilized for the interaction circuit of a wide band Gyro-TWT.