• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2140-2142
• /
• 2005

This paper presents the experimental results on the preliminary breakdown characteristics under a highly non-uniform electric field in $SF_6/CO_2$ gas mixtures. The impulse preliminary breakdown developments are investigated by the measurements of corona current and light emission images. As a result, the preliminary breakdown development mechanisms for both positive and negative polarities are same. The first streamer corona is initiated at the tip of needle electrode, and the leaders develop with a stepwise propagation and bridge the test gap. The pause time of leader pulses in the positive polarity is significantly shorter than that in the negative polarity. Also, the time interval between the first streamer corona onset and breakdown in the negative polarity was much longer than that in the positive polarity The discharge channel paths in the positive polarity were zigzag. On the other hands, the leader channel in the negative polarity was thicker than that in the positive polarity.

• Journal of Sensor Science and Technology
• /
• v.22 no.5
• /
• pp.364-368
• /
• 2013

Vibrational energy harvester based on piezoelectricity has been expected to be the dominant energy harvesting technology due to the advantages of high conversion efficiency, light weight and small size, night operation, etc. Its commercialization is just around the corner but the integration with power management electronics should be solved in advance. In this paper, therefore, fully-integrated design environment for piezoelectric energy harvesting systems is presented to assist co-design with the power management electronics. The proposed design environment is capable of analyzing the energy harvester including the package-induced damping effects and simulating the device and its power management electronics simultaneously. When the developed design environment was applied to the fabricated device, the simulated resonant frequency matched well with the experimental result with a difference of 2.97% only. Also, the complex transient response was completed in short simulation time of 3,001 seconds including the displacement distribution over the device geometry. Furthermore, a full-bridge power management circuit was modeled and simulated with the energy harvester simultaneously. Therefore the proposed, fully-integrated design environment is accurate and fast enough for the contribution on successful commercialization of piezoelectric energy harvester.

• Steel and Composite Structures
• /
• v.18 no.2
• /
• pp.357-374
• /
• 2015

Orthotropic decks composed of deck plate, ribs, cross beams and wearing surface are frequently used in industry to span long distances due to their light structures and load carrying capacities. As a result they are broadly preferred in industry and there are a lot of bridges of this type exist in the world. Nevertheless, some of them cannot sustain the anticipated service life and damages in form of cracks develop in steel components and wearing surface. Main reason to these damages is seen as the repetitive wheel loads, namely the fatigue loading. Solutions to this problem could be divided into two categories: qualitative and quantitative. Qualitative solutions may be new design methodologies or innovative materials, whereas quantitative solution should be arranging dimensions of deck structure in order to resist wheel loads till the end of service life. Wearing surface on deck plate plays a very important role to avoid or mitigate these damages, since it disperses the load coming on deck structure and increases the bending stiffness of deck plate by forming a composite structure together with it. In this study the effect of Elastic moduli, Poisson ratio and thickness of wearing surface on the stresses emerged in steel deck and wearing surface itself is investigated using a FE-model developed to analyze orthotropic steel bridges.

• Smart Structures and Systems
• /
• v.24 no.5
• /
• pp.649-657
• /
• 2019

Recently, an advanced video deflectometer based on the principle of off-axis digital image correlation was presented and advocated for remote and real-time deflection monitoring of large engineering structures. In engineering practice, measurement accuracy is one of the most important technical indicators of the video deflectometer. However, it has been observed in many outdoor experiments that data drift often presents in the measured deflection-time curves, which is caused by the instability of imaging system and the unavoidable influences of ambient interferences (e.g., ambient light changes, ambient temperature variations as well as ambient vibrations) in non-laboratory conditions. The non-ideal unstable imaging conditions seriously deteriorate the measurement accuracy of the video deflectometer. In this work, to perform high-accuracy deflection monitoring, potential sources for the drift error are analyzed, and a drift error model is established by considering these error sources. Based on this model, a simple, easy-to-implement yet effective reference point compensation method is proposed for real-time removal of the drift error in measured deflections. The practicality and effectiveness of the proposed method are demonstrated by in-situ deflection monitoring of railway and highway bridges.

• Journal of the Korean Society for Railway
• /
• v.20 no.3
• /
• pp.329-338
• /
• 2017

A recent trend of technical development in auxiliary-power-supplies (APS) is to replace 60Hz low frequency transformers with isolated type dc/dc converters. This paper introduces the technical trend in APS structures and proposes a power converter circuit suitable for high-efficient and light-weight APS. By utilizing the resonant converter, which achieves ZCS, to reduce switching losses, various types of APS structures (1-stage and 2-stage) are reviewed, and they are verified by simulation. The full-bridge resonant LLC converter is designed with a 1-stage power converting structure; the resonant converter topology is designed with a 2-stage power converting structure that has a pre-regulator converter to compensate for the wide input voltage range. Both a step-down converter and a step-up converter are designed and compared for the pre-regulator in the 2-stage structure. Operational characteristics are compared with simulation results and loss analyses are presented to proposes appropriate system structure and topologies.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.24 no.1
• /
• pp.27-40
• /
• 1997

This study investigated the effects of laser irradiation on the exposed pulp and the possibility of direct pulp capping with the $CO_2$ laser. Results were obtained from the observation of the residual pulpal healing process. Class V cavities on 48 anterior teeth from 8 adult dogs were prepared and pulp chambers were intentionally opened with dental explorer. The control group consisted of 16 teeth. $Dycal^{(R)}$(Caulk Co., U.S.A.) was applied to exposed site once bleeding was stopped. Cavities were sealed with $I.R.M^{(R)}$. In the experimental group 1 (16 teeth), laser(LASERSAT $CO_2^{(R)}$, Satelec Co.) was irradiated on the exposed pulp. The laser procedure followed the manufacturers recommendations for the treatment of human pulp(1.5 Watts, 0.2 seconds, unfocused), and cavities were sealed with $I.R.M^{(R)}$. In the experimental group 2 (16 teeth), laser was irradiated on the exposed pulp in a more powerful dosage(5.0 Watts, 0.2 seconds, unfocused), and cavities were sealed with $I.R.M^{(R)}$. Two dogs were sacrificed immediately after experiment and the others were sacrificed at intervals of one, three, and eight weeks respectively. All teeth were routinely processed and the pulpal tissues and odontoblastic layers were observed by the light microscope. The results were as follows; 1. In the control group, the initial mild inflammation had improved to normal by week eight. An active formation of reparative dentin was observed at week three, and at week eight, a firm dentin bridge was present beneath the $Dycal^{(R)}$ with no inflammatory responses in the remaining pulp. 2. In the experimental group 1, immediately following irradiation, the superficial shape of the exposed pulp was crater-like. And it was lined with the coagulated layer, $60{\sim}70{\mu}m$ in width. Moderate inflammatory pulpal conditions existing at week one were improved to mild at week eight. And from the week three specimens, a reparative dentin formation was observed in the adjacent odontoblastic layer of the exposed site. A dentin bridge at the exposed site, however, did not form during the experimental period. 3. In the experimental group 2, the width of the coagulation layer lining the crater was $70{\sim}130{\mu}m$. Beneath the coagulated layer, severe inflammatory pulpal responses were observed at week one, and conditions did not improve during the experimental period.

• The Journal of Korean Academy of Prosthodontics
• /
• v.38 no.2
• /
• pp.226-241
• /
• 2000

Recently a new generation of crown and bridge veneering resins containing submicron glass fillers was introduced. These ultrasmall particle hybrid composite materials distinguish themselves, compared with conventional microfill crown and bridge resins, through improved mechanical properties. It is claimed that these composites are suitable for metal free crowns and even bridges using fiber reinforcement. The purpose of this study was to evaluate the effect of thermal cycling on the tensile strength of the following veneering composites: Artglass(Heraeus Kulzer Co., Wehrheim, Germany), Estonia(Kuraray Co.. Japan), Sculpture(Jeneric Pentron Co., Wallingford, U.S.A.), and Targis(Ivoclar Co., Schaan Liechenstein). According to manufacturer's instructions, rectangular tensile test specimens measuring $1.5{\times}2.0{\times}4.5mm$ were made using a teflon mold. Whole specimens were divided into two groups. One group was dried in a desiccator at $25^{\circ}C$ for 10 days, and another group was subjected to thermal cycling($10,000{\times}$) in water($5/55^{\circ}C$). All test specimens were placed in a universal testing machine and loaded until fracture with a crosshead speed of 0.5mm/min. Weibull analysis and Tukey's test were used to analyze the data. The fracture surfaces of specimens were observed in SEM and the aliphatic C=C absorbance peak of Estenia and Targis resin was analyzed using Fourier transform infrared(FTIR) spectroscopy. Within the limitations imposed in this study, the following conclusions can be drawn: 1. Both in drying condition and thermal cycling condition, the highest tensile strength was observed in Estenia testing group(p<0.05). 2. The strength data were at to single-mode Weibull distribution, and the Weibull modulus of all veneering composite resin specimens increased after thermal cycling treatment. 3. After thermal cycling test, the highest tensile strength was observed in the Estenia group, and the lowest value was observed in the Targis group. The tensile strength values showed the significant differences between each group(p<0.05) 4. The aliphatic C=C absorbance peak of Estonia and Targis resin was decreased after light curing, and there was no distinct change after thermal cycling.

• Journal of the Korea Concrete Institute
• /
• v.23 no.3
• /
• pp.281-287
• /
• 2011

Recently, bridge construction technology has made great progress from development of high performance materials and new bridge types. However, most technology are based on methods of cast-in-place and material cost saving. The method of cast-in-place concrete causes environmental damages and costumer complaints. Especially, under bad weather conditions, the construction can not proceed. To overcome these disadvantages, new construction methods were developed to reduce construction time. These methods are called precast method. Most prefabricated methods have been applied to superstructure constructions of bridges, but very minutely applied to substructure constructions. The most important agendas on precast method are light weight and transportability of the precasted members, because very strict transporting specifications exist for road transportation of the precasted members. For example, the weight and length of coping members may be larger than the available transporting vehicles. Although column is constructed by precast method to save construction time, if coping member is constructed by cast-in-place method, then the column construction time reduction becomes meaningless. Therefore, in this study, a new precast coping member and a connecting system of column-coping member are proposed. The proposed method is verified by analyzing their ultimate performance through analysis and experimental study.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.22 no.1
• /
• pp.43-53
• /
• 1992

The purpose of this study was to investigate the effects of irradiation on the microvascular structure of the submandibular gland in rats. For this study, 110 male rats were singly irradiated with the dose of 10Gy or 20Gy to their neck region by 6MV X-irradiation and sacrificed on the 1st, 3rd, 7th, 14th and 28th day after irradiation. The author observed distribution and structural changes of the microvasculature in rat submandibular glands using a scanning electron microscope by forming vascular resin casting. The author observed ultrastructural changes of the endothelial cells using a transmission electron microscope, and also histologic changes using a light microscope at Hematoxylin and Eosin staining and PAS staining process. The results of the irradiation effects on the microvasculature in rat submandibular gland were as follows: By light microscopic examination, the dilation of small vessels were observed until the 7th day after irradiation. After then, the vascular constriction and decrease in number of small vessels were noticed. Changes were greater on 20Gy irradiated group than on lOGy irradiated group. The reaction to PAS staining at acinar cells was decreased just after irradiation, but gradually recovered with days. There was no specific difference between two irradiated groups. By scanning electron microscopic examination, general findings on the two irradiated groups were similar. The dilation of conduits and meandering were observed on the 3rd day after irradiation. Decrease of capillary density and blunt ended small vessels were appeared on the 7th day after irradiation. After that, findings of the tortuous and twisted vascular running and coarseness of capillary lumen were increased. Changes were greater on 20Gy irradiated group than on l0Gy irradiated group. By transmission electron microscopic examination, increase of the formation of cytoplasmic process was observed on the 3rd day after irradiation. After that, swelling of endothelial cell and bridge formation of cytoplasmic processes were also observed, but destruction of endothelial cell and loss of basement membrane were observed only on 20Gy irradiated group on the 28th day after irradiation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.58 no.1
• /
• pp.7-13
• /
• 2020

Purpose: This study was to evaluate marginal and internal discrepancy of 3-unit fixed dental prostheses (FDP) fabricated by subtractive manufacturing and additive manufacturing. Materials and methods: 3-unit bridge abutments without the maxillary left second premolar were prepared (reference model) and the reference model scan data was obtained using an intraoral scanner. 3-unit fixed dental prostheses were fabricated in the following three ways: Milled 3-unit FDP (MIL), digital light processing (DLP) 3D printed 3-unit FDP (D3P), stereolithography apparatus (SLA) 3D printed 3-unit FDP (S3P). To evaluate the marginal/internal discrepancy and precision of the prosthesis, scan data were superimposed by the triple-scan protocol and the combinations calculator, respectively. Quantitative and qualitative analysis was performed using root mean square (RMS) value and color difference map in 3D analysis program (Geomagic control X). Statistical analysis was performed using the Kruskal-Wallis test (α=.05), MannWhitney U test and Bonferroni correction (α=.05/3=.017). Results: The marginal discrepancy of S3P group was superior to MIL and D3P groups, and MIL and D3P groups were similar. The D3P and S3P groups showed better internal discrepancy than the MIL group, and there was no significant difference between the D3P and S3P groups. The precision was excellent in the order of MIL, S3P, and D3P groups. Conclusion: Within the limitation of this study, the 3-unit fixed dental prostheses fabricated by additive manufacturing showed better marginal and internal discrepancy than the those of fabricated by subtractive manufacturing, but the precision was poor.