• 한국안전학회지
• /
• 제9권4호
• /
• pp.3-10
• /
• 1994

This study examines fracture characteristics of wire rope of 6$\times$37+FC 14mm B degree, Which has been widely used for the strength support for machinery, cranes and shipping. The examination Is based on the fellowing experimental conditions. Firstly, this study analyzes the effect of the strength of wlre rope. When number of broken wires is occuring at the level of 5%, 10% and 15% degree respectively in the following two cases：1) Case of broken down to each strand equally. 2) Case of broken down to one strand only. Secondly, this study analyzes the effect of corrosion on the strength of wire rope. Corrosion times are 72hours, 144hours and 216hours corrosion respectively under following conditions. 1) Case of only a corrosion without wire breaking. 2) Case of corrosion after 5% degree wire breaking to each strand equally. Some outcomes of these experiment are as follows. 1) From the of tension test, We can find that the ratio of strength reduction case of wire broke down to one strand concentrically is greater than that ratio case of broke down to each strand equally. 2) From the corrosion test, We can also find that the ratio of strength reduction case of corroded after 5% degree wire breaking to each strand equally Is greater than that ratio case of corroded without wire breaking. 3) After comparing theoretical fracture load of wires with experimental fracture load of wires, we can find the fracture load of the case of broken down to each strand equally is most similar to theoretical fracture load. 4) It is proposed that safety rules on wire rope in the Industrial safety and healthy labor of law have to change “breaking over 10% of number of wires in one strand of wire rope(excluded filler wire )”has to be replaced by“breaking over 10% of number of all wires in all strand of wire rope(excluded filler wire)”

• 한국기계가공학회지
• /
• 제15권1호
• /
• pp.26-33
• /
• 2016

In this study, a new method to develop a fixed diamond wire for silicon wafer machining by the multi-wire cutting method was developed. The new twist diamond wire has improved performance with high breaking strength and chip flutes structure. According to these characteristics, the new twist diamond wire can be used in the higher speed multi-wire cutting process with a long lifetime. Except the design of the new structure, the twist diamond wire is coating by electroless-electroplating process. It is good for reducing breakage and the falling-off of diamond grains. Based on the silicon material removal mechanism and performance of the wire-cutting machine, the optimal processing condition of the new twist diamond wire has been derived via mathematical analysis. At last, through the tensile testing and the machining experiments, the performance of the twist diamond wire has been obtained to achieve the development goals and exceed the single diamond wire.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1632-1636
• /
• 2007

Generally, fine high carbon steel wire is produced using a multi-pass drawing process with speeds over 1000 m/min. The productivity of the wire drawing mainly depends on achieving the highest drawing speed without breaking the wire. In the multi-pass drawing, as the final drawing speed increases, the temperature rises several hundred Celsius. High temperature of wire increases the brittleness and leads to breaks. The objective of this study is to design pass schedule and wire drawing machine for superhigh speed. In the drawing experiment, it was possible to increase the productivity through the increase in final speed from 1100 m/min to 2000 m/min.

• 한국안전학회지
• /
• 제25권6호
• /
• pp.70-74
• /
• 2010

For each strand of wirerope sling, the international standards, ISO-8794, EN-13414 specify that the splice shall have five series of load carrying tucks. At least three of the load carrying tucks shall be made with the whole strand. And, the breaking force of the splice shall not be less than 70% or 80% of that of rope. But, There are no prescriptions for splicing types against different efficiency of each splicing type being used many workplace. In this study, analysis the work limit load efficiency according to variation of number of tucks and splicing types by experimental method As a result, the number of tucks 3+2 had the highest breaking efficiency.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.863-868
• /
• 2004

Reheating furnace is an essential facility of a rod mill plant where a billet is heated to the required rolling temperature so that it can be milled to produce wire. Sometimes, it is also necessary to control a transient billet temperature pattern according to the material characteristics to prevent a wire from breaking. Though it is very important objective to obtain a correct information of a billet temperature during furnace operation. Consequently, a billet temperature profile must be estimated. In this paper, a billet heat transfer model based on FEM (Finite Element Method) with spatially distributed emission factors is proposed and a measurement is also carried out for two different furnace operation conditions. Finally, the difference between the model outputs and the measurements is minimized by using the new optimization algorithm named uDEAS(Univariate Dynamic Encoding Algorithm for Searches) with multi-step tuning strategy. Hence, the information of billet temperatures can be obtained by using proposed model on various furnace operation conditions.

• 한국항해항만학회지
• /
• 제42권6호
• /
• pp.388-394
• /
• 2018

선박이 계류삭을 이용하여 부두에 접안하는 경우, 과도한 선박 속력은 계류삭이 절단되는 사고를 야기할 수 있다. 이러한 계류삭의 파단 사고를 방지하기 위해서는 계류삭 파단 방지에 선박의 한계치 접안 속력을 알아야 한다. 본 연구의 목적은 계류삭 파단을 방지하기 위한 선박의 한계치 접안 속력 추정에 있다. 본 연구의 핵심은 선박의 속력을 모르는 경우 선박제원과 계류삭 제원을 이용하여 접안 시 한계치 접근 속력을 추정하는 방법이다. 본 연구에서는 선체저항과 계류삭의 탄성력 등에 관한 이론을 바탕으로 한계치 접안 속력의 추정 방법과 절차를 제안하였다. 135K LNG 선박과 IWRC, $6{\times}36$의 강선 계류삭을 대상으로 한계치 접안 속력을 추정한 결과, 추정한 접안 속력으로 접안하는 경우 계류삭이 파단이 되지 않는 것으로 분석되어 제안한 방법이 유효함을 알았다. 본 연구에서 제안한 방법은 실제 선박에서 계류삭 파단을 방지하는데 기여할 수 있을 것으로 기대된다.

• 전기학회논문지
• /
• 제61권12호
• /
• pp.1953-1958
• /
• 2012

The major causes of electrical fire are classified to short circuit fault, overload fault, electric leakage and electric contact failure. The occurrence factor of the fire is electric arc or spark accompanied with such electric faults, specially short circuit faults. Earth Leakage Circuit Breaker (ELB) and Molded_case Circuit Breaker (MCCB), that is, Residual Current Protective Devices (RCDs) used on low voltage distribution lines cut off earth leakage and overload, but the RCD can not cut off electric arc or spark to be a major factor of electrical fire. As the RCDs which are applied in low voltage distribution panel are prescribed to rated breaking time about 30ms(KS C 4613), the RCDs can't perceive to the periodic electric arc or spark of more short wavelength level. To improve such problem, this paper proposes a prevention apparatus using the line voltage drop of neutral wire and some semiconductor switching devices. Some experimental tests of the proposed apparatus confirm the validity of the analytical results.

• 조명전기설비학회논문지
• /
• 제22권2호
• /
• pp.71-79
• /
• 2008

철도 고압배전선로의 경우 궤도를 따라 양방향으로 선로연변에 통신 및 신호설비와 병행하여 가공 또는 지중선로로 설치되어 있다. 가공선로의 경우에는 대기중에 노출되어 있어 뇌격, 폭풍우, 염해 등 자연현상으로 인한 고장발생이 다수 발생하고 있으며, 이에 따른 보호장치의 오 부동작이 빈번하게 발생하고 있다. 철도 고압배전선로에서 발생하는 사고 중 가장 많은 것은 1선 지락이지만 이밖에 선간 단락, 심할 경우에는 3선 지락(단락)으로까지 진전되는 사고가 있을 뿐만 아니라 단선 사고까지 발생하는 경우도 있다. 따라서 사고를 방지하기 위해서는 보다 상세한 점검보수가 필요하며, 고장발생시 조기발견과 신속한 고장처리는 철도안전수송에 중요하다. 본 논문에서는 철도 고압배전계통의 주류를 이루게 될 22.9[kV] 직접접지 계통을 대상으로 고장 발생시 고장 위치를 신속하게 표정할 수 있는 고장점 표정 알고리즘 개발을 위해 22.9[kV] 고압배전계통을 모델링 하여 특성해석과 고장해석을 수행하였고, 정확한 고장점 표정이 가능한 반복계산법을 이용한 알고리즘을 제시하였으며, 사례연구를 통해 성능을 입증하였다.

• 대한전자공학회논문지SD
• /
• 제42권11호
• /
• pp.23-32
• /
• 2005

회로도면 자동생성 분야는 지난 수십 년간 HDL기반 설계과정에서 사용되어 왔다. 그러나 회로 도면은 더욱 복잡해져서 레지스터 및 시스템 레벨에서 자동 생성된 회로도면을 보고 신호의 흐름을 파악하기 어렵다. 이와 같이 복잡해진 회로도면의 가독성을 향상시키기 위해 본 논문에서는 4가지 기법, 즉 i ) 심볼이나 터미널들과 같이 반복되는 회로 패턴을 벡터 형태로 치환, ii) 피드백 루프 절단 알고리즘 개선, iii) 번들 네트 생성시 발생하는 다단 연결을 간결 화할 수 있는 압축 탭, iv) 연결도에 따라 블록열을 구분하고 정렬하는 알고리즘을 제안한다. 제안된 회로도면 생성 기법의 효용성을 확인하기 위해 도면 자동생성 프로그램을 개발하고, 계층적으로 설계된 미디어 프로세서의 다양한 모듈의 도면을 생성시켰다. 실험한 결과 도면 면적을 비롯하여 배선 수, 길이 등을 $90\%$까지 감소시키고 가독성을 높이는 효과를 보였으며 블록의 분산 및 빈 공간 발생을 억제하는 효과를 보였다.

• 전기학회논문지
• /
• 제67권5호
• /
• pp.644-650
• /
• 2018

According to a miniaturization and integration of electric device, a little size of fuse satisfying the current carrying capacity as well as an explosive tolerance and current interrupt rating are required. Fe-Ni alloy is applied to decrease an oxidation of fuse elements. A resistance and T.C.R(temperature coefficient of resistance) of a fuse are analyzed by changing a content of Ni And full rated current I-T curve from 1A to 6.3A has been tested. In order to an explosive energy, a straight wire type is selected to reduce a fuse melting time. An interrupt rating test was conducted by changing a content of Ni and the optimal content of Ni is to be 40%.