• Journal of Power System Engineering
• /
• v.3 no.3
• /
• pp.22-28
• /
• 1999

The injected liquid does not break-up instantly after injection for diesel engine. There is some unbroken portion, which is the liquid core(The length of liquid core is called the break-up length) in the spray. If the liquid core is longer than the depth of the bowl in the small DI diesel engine, the liquid core impinges on the surface of the piston. Once the liquid core impinges on the surface, it cannot ignite or burn rapidly and thus prolongs burning time with a degradation in thermal efficiency. The break-up length of a diesel spray in a compressure vessel was measured by an electric resistance method, A voltage was applied between the nozzle and screen, bar, needle electrode inserted at various axial and radial positions into atomizing sprays. As a result, a current flows not only in the region of liquid core but also through the droplets of the spray. It is found that the break-up length measured with screen electrode is overestimated. The break-up length of the spray is found to be proportional to the square root of the density ratio of fuel and surrounding gas. The break-up length of the spray decreases as the injection pressure and the back pressure increase.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.109-115
• /
• 2016

In this paper, In this paper, we use two methods to compare the slim speakers. That way, the diaphragm scan using laser and diaphragm photographed using a thermal imaging camera. Slim speaker has the structure of a flat plate type. Break-up mode by this characteristic is displayed in a larger size. Further, since the installation space is narrow, it has limited moving coil cooling. As a result, the break-up mode slim speakers, a significant impact on quality. In this study, try to connect the break-up mode of the diaphragm, the heat transfer mode of the diaphragm. Experiment for comparison, a two-step. The first step is to measure the divided vibration through the vibration plate scan. The second step measures the diaphragm photographed using a thermal imaging camera. Then, compare the results of both of the same frequency. Thus, comparing the heat transfer pattern and the pattern of break-up mode. Tend to be analysis of break-up mode from the pattern comparison, and document for the optimum design.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.417-422
• /
• 1996

The KNGR has an advanced ECCS design feature which employs four mechanically-separated SI trains where each train consisting of one HPSI pump and one SIT injects ECC water directly into the reactor vessel downcomer annulus. To demonstrate that the KNGR ECCS design features meet the EPRI ALWR requirements of no core uncovery for a break of up to 6 inch diameter, small break LOCA cases with various break sizes were analyzed using a best-estimate analytical procedure. Two kinds of break locations are considered: cold leg and DVI line breaks. It was observed that the KNGR ECC design can tolerate a cold leg break of up to 10 inches with no core uncovery. However. since DVI line break with 6 inch diameter undergoes slight core uncovery. further investigation is required for KNGR SIS optimization.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.4
• /
• pp.333-336
• /
• 2017

A speaker diaphragm generates a divided vibration. The influence of the break-up mode is sufficient to cause a shape change in the diaphragm. In this paper, is widely used in ultra-thin multi-media devices, including smart phones is the advance guard of the IT sector, the micro-speakers and its target. Micro-speakers are different from general speakers. The plate has structural form and space constraints. In particular, they utilize a closed-type drive space. It is difficult to provide cooling for the auxiliary suspension structure because of the heat generated in the moving coil. The present study considered the relationship between the break-up mode and the heat transfer of the diaphragm. An experiment was conducted in two stages to compare the embodiment of the break-up mode and heat transfer in a certain frequency range. The changes in the heat were determined through measurements and thermal imaging of the break-up mode. The break-up mode tendency of the diaphragm could be rapidly predicted based on the imaging results using the thermal imaging camera. This will help in the optimal design of micro-speakers.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.06a
• /
• pp.159-165
• /
• 2000

In this paper the residual stresses on lubricated sliding surfaces were measured during break-in procedure and up to scuffing by the X-ray diffraction method. The cylinder-on-disk type tribometer was used with the line-contact geometry. Scuffing tests were done using a constant load. In the break-in procedure the loads were increased from very low values in several steps. It was found that the sliding surfaces with break-in represented relatively higher values of residual compressive stresses than those without break-in. The residual stresses below the surfaces showed the small amount of stress increases. The results of scuffing tests with and without break-in showed the same trends as break-in tests did. However, in case of tests with break-in procedure the stresses below the surfaces showed very large increases in the residual compressive stresses. From the tests of break-in and scuffing, it was found that the increases in scuffing lives were related with the increases of residual stresses on the lubricated sliding surfaces with break-in.

• Tribology and Lubricants
• /
• v.16 no.3
• /
• pp.182-187
• /
• 2000

In this paper the residual stresses on lubricated sliding surfaces were measured during break-in procedure and up to scuffing by the X-ray diffraction method. The cylinder-on-disk type tribometer was used with the line-contact geometry. Scuffing tests were done using a constant load. In the break-in procedure the loads were increased from very low values in several steps. It was found that the sliding surfaces with break-in represented relatively higher values of residual compressive stresser than those without break-in. The residual stresses below the surfaces showed the small amount of stress increases. The results of scuffing tests with and without break-in showed the same trends as break-in tests did. However, in case of tests with break-in procedure the stresses below the surfaces showed very large increases in the residual compressive stresses. From the tests of break-in and scuffing, it was found that the increases in scuffing lives were related with the increases of residual stresses on the lubricated sliding surfaces with break-in.

• Nuclear Engineering and Technology
• /
• v.36 no.3
• /
• pp.276-284
• /
• 2004

This paper presents the results of the TEXAS-V computer code simulations of FARO L-14, L-28, and L-33. The old break-up model and new break-up model are tested to compare the respective simulations of each. As these experimental data sets cover a wide range of ambient pressures, sub-cooling of the water pool, and the melt jet diameters, the results of the simulations will be beneficial in assessing the TEXAS-V code's capability to predict the steam explosion phenomena in a prototypical reactor case. The current model was found to have some deficiencies, and the modules for the fragmentation, the equation of state, and the interfacial area for each flow regime in TEXAS-V were improved for the simulation of FARO L28 and FARO L-33.

• Journal of Biosystems Engineering
• /
• v.39 no.4
• /
• pp.283-289
• /
• 2014

Purpose: This study was carried out to evaluate the labor requirement and the cost-reducing effects of the pick-up type pulse crop harvester compared with those of conventional harvesting for soybeans and red beans. Methods: The labor requirement and the cost to gather, thresh, and clean for conventional harvesting operations were surveyed; those for the pick-up type pulse crop harvester were estimated for soybeans and red beans. The annual capacity of the harvester and the break-even area of the two harvesting methods were also estimated. Results: For soybean harvesting, the labor requirement of 0.57 hour-persons/10 a for the pick-up type pulse crop harvester reflects a 91.9% reduction in the labor requirement of 7.00 hour-persons/10 a for conventional harvesting. Machinery costs of 51,300 won/10 a for the harvester were estimated for an annual harvesting area of 52.5 ha/year, representing a reduction of 33.3% from the 78,700 won/10 a cost of conventional harvesting. A break-even area of 28.4 ha was estimated for the two harvestings. For red bean harvesting, the labor requirement of 0.57 hour-persons/10 a for the harvester reflects a 92.6% reduction in the labor requirement of 7.66 hour-persons/10 a for conventional harvesting. For an annual harvesting area of 52.5 ha/year, annual capacity of 52.5 ha/year and machinery costs of 51,700 won/10 a were estimated for the harvester, reflecting a reduction of 44.7% in the cost of 93,500 won/10 a for conventional harvesting. A break-even area of 23.1 ha was estimated for the two harvestings. A governmental subsidy for purchasing the harvester could contribute to reducing the break-even area and harvesting costs. Conclusions: The pick-up type pulse crop harvester for soybean and red bean harvesting could reduce the labor requirement and costs of conventional harvesting, and a governmental subsidy for purchasing the harvester will improve the economics of the harvester for efficient mechanical harvesting.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.5
• /
• pp.113-118
• /
• 2015

Mobile wireless networks have received a lot of attention as a future wireless network due to its rapid deployment without communication infrastructure. In these networks communication path between two arbitrary nodes break down because some links in the path are beyond transmission range($r_0$) due to the mobility of the nodes. The set of total path break down time(${\bigcup}T_i$), which is the union of path break down time of every node pair, can be a good measure of the connectivity of the dynamic mobile wireless network. In this paper we show that the distribution of the total path break down time can be approximated as a exponential probability density function and confirms it through experimental data. Statistical knowledge of break down time enables quantitative prediction of delay, packet loss between two nodes, thus provides confidence in the simulation results of mobile wireless networks.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.5
• /
• pp.527-536
• /
• 2010

Although the bubble-floc agglomerate floated and formed the float layer on the surface of the water in the DAF process, after inducing in the thickening tank a part of the bubble-floc agglomerate come up again to the surface and the other is settled at the bottom of the tank. The bubble-floc agglomerate divided into two group as the scum on the surface and the sludge of the bottom gives rise to operational troubles for the thickening process. In order to find out the cause of break-up and the effective thickening method for sludge from the DAF process, the composition of the bubble-floc agglomerate was investigated and a series of flotation experiments carried out. There was no difference of composition between the scum on the surface and the sludge of the bottom in the thickening tank. The coagulation was not effective to improve the trouble that the bubble-floc agglomerate divided into the scum and the sludge. It was estimated that for the bubble-floc agglomerate of thickening tank the trouble was caused by not the change or the difference of chemical composition but whether the bubble-floc agglomerate hold bubbles. Furthermore, for the effective thickening of sludge from the DAF process, it is required an additional flotation applied the AS ratio depending upon the solid concentration of sludge as the operation parameter.