• 동력기계공학회지
• /
• 제3권3호
• /
• pp.22-28
• /
• 1999

The injected liquid does not break-up instantly after injection for diesel engine. There is some unbroken portion, which is the liquid core(The length of liquid core is called the break-up length) in the spray. If the liquid core is longer than the depth of the bowl in the small DI diesel engine, the liquid core impinges on the surface of the piston. Once the liquid core impinges on the surface, it cannot ignite or burn rapidly and thus prolongs burning time with a degradation in thermal efficiency. The break-up length of a diesel spray in a compressure vessel was measured by an electric resistance method, A voltage was applied between the nozzle and screen, bar, needle electrode inserted at various axial and radial positions into atomizing sprays. As a result, a current flows not only in the region of liquid core but also through the droplets of the spray. It is found that the break-up length measured with screen electrode is overestimated. The break-up length of the spray is found to be proportional to the square root of the density ratio of fuel and surrounding gas. The break-up length of the spray decreases as the injection pressure and the back pressure increase.

• 전자공학회논문지
• /
• 제53권10호
• /
• pp.109-115
• /
• 2016

이 논문에서는 레이저를 통한 진동판 스캔과 열화상 카메라를 사용한 진동판 촬영, 두 가지 방법을 비교하며 슬림 스피커의 분할 진동을 검출하는 방법에 대해 살펴본다. 슬림 스피커는 평판형의 구조적인 특성상 분할진동이 두드러지게 나타나고, 설치되는 공간이 좁아 무빙 코일에서 발생하는 열의 냉각이 제한적이다. 이런 특성으로 인해 슬림 스피커에서 분할진동이 제품의 품질에 큰 영향을 미친다. 본 연구에서는 진동판에서 일어나는 분할진동의 영향과 무빙 코일에 의한 진동판의 열전달 관계를 비교 탐색한다. 비교를 위한 실험은 분할진동 모드의 측정과 진동판의 열 변화 측정을 진동판 스캔과 열화상 카메라 촬영의 2단계의 실험으로 진행한다. 동일 주파수에서 발생하는 분할진동 모드와 열전달 형태를 비교하여 서로 간에 어떤 영향을 미치고 있는 지 파악할 수 있다. 그리고 이를 통해 발견한 연관성을 통해 쉽게 촬영할 수 있는 열화상만으로도 슬림 스피커가 가지는 분할진동의 형태와 경향성을 빠르게 파악하여 최적 설계에 도움이 되는 자료로 사용할 수 있을 것이다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(2)
• /
• pp.417-422
• /
• 1996

The KNGR has an advanced ECCS design feature which employs four mechanically-separated SI trains where each train consisting of one HPSI pump and one SIT injects ECC water directly into the reactor vessel downcomer annulus. To demonstrate that the KNGR ECCS design features meet the EPRI ALWR requirements of no core uncovery for a break of up to 6 inch diameter, small break LOCA cases with various break sizes were analyzed using a best-estimate analytical procedure. Two kinds of break locations are considered: cold leg and DVI line breaks. It was observed that the KNGR ECC design can tolerate a cold leg break of up to 10 inches with no core uncovery. However. since DVI line break with 6 inch diameter undergoes slight core uncovery. further investigation is required for KNGR SIS optimization.

• 대한기계학회논문집A
• /
• 제41권4호
• /
• pp.333-336
• /
• 2017

스피커 진동판은 고유 특성에 의해 분할진동을 발생 시킨다. 이 분할진동은 진동판의 형상 변화를 가져올 정도로 뚜렷한 영향을 주는데, 본 논문에서는 IT 분야의 첨병인 스마트 폰을 포함한 초박형 멀티미디어 기기에서 많이 사용되는 마이크로 스피커를 그 대상으로 삼는다. 마이크로 스피커는 일반적인 스피커와 다른 평판형의 구조적인 형태와 공간적인 제약이 존재한다. 특히 구동 공간이 밀폐형으로 설계되어 무빙 코일에서 발생하는 열의 냉각이 열악하고 보조적인 서스펜션 구조를 갖추기 어렵다. 본 연구에서는 진동판의 열전달과 분할진동 모드의 연관성을 연구한다. 이를 위해 진동판의 레이저 스캔을 통한 분할진동 측정과 열화상 카메라 촬영을 통한 열변화 측정의 두 단계로 나누어 실험을 진행한다. 이를 통해 특정 주파수 범위에서 분할진동 모드와 열전달 형태를 비교함으로써, 열화상 카메라를 통한 촬영 결과로 진동판 분할진동 모드의 경향성을 빠르게 예상할 수 있어, 마이크로 스피커의 최적 설계에 도움이 되는 지표를 제공할 수 있을 것으로 기대한다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.159-165
• /
• 2000

In this paper the residual stresses on lubricated sliding surfaces were measured during break-in procedure and up to scuffing by the X-ray diffraction method. The cylinder-on-disk type tribometer was used with the line-contact geometry. Scuffing tests were done using a constant load. In the break-in procedure the loads were increased from very low values in several steps. It was found that the sliding surfaces with break-in represented relatively higher values of residual compressive stresses than those without break-in. The residual stresses below the surfaces showed the small amount of stress increases. The results of scuffing tests with and without break-in showed the same trends as break-in tests did. However, in case of tests with break-in procedure the stresses below the surfaces showed very large increases in the residual compressive stresses. From the tests of break-in and scuffing, it was found that the increases in scuffing lives were related with the increases of residual stresses on the lubricated sliding surfaces with break-in.

• Tribology and Lubricants
• /
• 제16권3호
• /
• pp.182-187
• /
• 2000

In this paper the residual stresses on lubricated sliding surfaces were measured during break-in procedure and up to scuffing by the X-ray diffraction method. The cylinder-on-disk type tribometer was used with the line-contact geometry. Scuffing tests were done using a constant load. In the break-in procedure the loads were increased from very low values in several steps. It was found that the sliding surfaces with break-in represented relatively higher values of residual compressive stresser than those without break-in. The residual stresses below the surfaces showed the small amount of stress increases. The results of scuffing tests with and without break-in showed the same trends as break-in tests did. However, in case of tests with break-in procedure the stresses below the surfaces showed very large increases in the residual compressive stresses. From the tests of break-in and scuffing, it was found that the increases in scuffing lives were related with the increases of residual stresses on the lubricated sliding surfaces with break-in.

• Nuclear Engineering and Technology
• /
• 제36권3호
• /
• pp.276-284
• /
• 2004

This paper presents the results of the TEXAS-V computer code simulations of FARO L-14, L-28, and L-33. The old break-up model and new break-up model are tested to compare the respective simulations of each. As these experimental data sets cover a wide range of ambient pressures, sub-cooling of the water pool, and the melt jet diameters, the results of the simulations will be beneficial in assessing the TEXAS-V code's capability to predict the steam explosion phenomena in a prototypical reactor case. The current model was found to have some deficiencies, and the modules for the fragmentation, the equation of state, and the interfacial area for each flow regime in TEXAS-V were improved for the simulation of FARO L28 and FARO L-33.

• Journal of Biosystems Engineering
• /
• 제39권4호
• /
• pp.283-289
• /
• 2014

Purpose: This study was carried out to evaluate the labor requirement and the cost-reducing effects of the pick-up type pulse crop harvester compared with those of conventional harvesting for soybeans and red beans. Methods: The labor requirement and the cost to gather, thresh, and clean for conventional harvesting operations were surveyed; those for the pick-up type pulse crop harvester were estimated for soybeans and red beans. The annual capacity of the harvester and the break-even area of the two harvesting methods were also estimated. Results: For soybean harvesting, the labor requirement of 0.57 hour-persons/10 a for the pick-up type pulse crop harvester reflects a 91.9% reduction in the labor requirement of 7.00 hour-persons/10 a for conventional harvesting. Machinery costs of 51,300 won/10 a for the harvester were estimated for an annual harvesting area of 52.5 ha/year, representing a reduction of 33.3% from the 78,700 won/10 a cost of conventional harvesting. A break-even area of 28.4 ha was estimated for the two harvestings. For red bean harvesting, the labor requirement of 0.57 hour-persons/10 a for the harvester reflects a 92.6% reduction in the labor requirement of 7.66 hour-persons/10 a for conventional harvesting. For an annual harvesting area of 52.5 ha/year, annual capacity of 52.5 ha/year and machinery costs of 51,700 won/10 a were estimated for the harvester, reflecting a reduction of 44.7% in the cost of 93,500 won/10 a for conventional harvesting. A break-even area of 23.1 ha was estimated for the two harvestings. A governmental subsidy for purchasing the harvester could contribute to reducing the break-even area and harvesting costs. Conclusions: The pick-up type pulse crop harvester for soybean and red bean harvesting could reduce the labor requirement and costs of conventional harvesting, and a governmental subsidy for purchasing the harvester will improve the economics of the harvester for efficient mechanical harvesting.

• 한국인터넷방송통신학회논문지
• /
• 제15권5호
• /
• pp.113-118
• /
• 2015

이동 무선망은 통신기반 설치가 필요 없는 빠르고 쉬운 망 구성 등의 장점으로 미래의 통신망으로 많은 주목을 받고 있다. 이동 무선망에서 임의의 두 노드간의 통신 경로는 노드의 이동성으로 인해 어떤 링크에서는 전송 범위($r_0$)를 벗어나 경로 붕괴가 일어나고 통신이 불가능하게 된다. 모든 노드 쌍의 경로 붕괴 시간의 모음인 총 경로붕괴 시간 집합(${\bigcup}T_i$)은 이동 무선망의 동적인 연결 상태를 측정하는 좋은 척도가 될 수 있다. 본 논문에서는 총 경로붕괴 시간의 확률 밀도함수는 지수함수로 근사화 될 수 있음을 보이고 실험 데이터를 통해서 확인하였다. 경로붕괴 시간에 대한 통계적 특성을 알면 이동 무선망에서의 노드 간 지연, 패킷 손실률 등에 대한 정량적 예측을 할 수 있고 시뮬레이션 결과에 대한 확신을 더해 주게 된다.

• 상하수도학회지
• /
• 제24권5호
• /
• pp.527-536
• /
• 2010

Although the bubble-floc agglomerate floated and formed the float layer on the surface of the water in the DAF process, after inducing in the thickening tank a part of the bubble-floc agglomerate come up again to the surface and the other is settled at the bottom of the tank. The bubble-floc agglomerate divided into two group as the scum on the surface and the sludge of the bottom gives rise to operational troubles for the thickening process. In order to find out the cause of break-up and the effective thickening method for sludge from the DAF process, the composition of the bubble-floc agglomerate was investigated and a series of flotation experiments carried out. There was no difference of composition between the scum on the surface and the sludge of the bottom in the thickening tank. The coagulation was not effective to improve the trouble that the bubble-floc agglomerate divided into the scum and the sludge. It was estimated that for the bubble-floc agglomerate of thickening tank the trouble was caused by not the change or the difference of chemical composition but whether the bubble-floc agglomerate hold bubbles. Furthermore, for the effective thickening of sludge from the DAF process, it is required an additional flotation applied the AS ratio depending upon the solid concentration of sludge as the operation parameter.