• 한국조경학회지
• /
• 제27권1호
• /
• pp.101-109
• /
• 1999

The purpose of this study is to analyse types and forms of branch-road in traditional korean villages. To do this, this study has selected and measured 87 branch-road cases of five traditional villages. An analysis of the case study has revealed the following results : 1. Branch-roads have four formations : 3 way, 4 way, multi-way and others. 2. Branch-roads comprise 64 percent of 3 way, 18 percent of 4 way, 8 percent of multi-way and 9 percent of others, respectively. 3. Topographic conditions have mostly affected the formation of branch-roads. 3 way of branch - roads are easily found in flat village. 4 way are multi-way of branch-road are found in semi-hilly and hilly village 4. 3 way of branch-roads have three types: T-type, Y-type, and y-type. 5. T-types are easily found in flat village, but Y-type and y-type are found in semi-hilly and hilly village. 6. Each angle of T-type is 171,99,90, respectively. It has turned out 8 degree is slightly deviated form the square. 7. Y-type of branch-road has an asymmetric form, comprising 145, 128, 87 degree of the angle, compared to 150, 150, 60 degree of symmetric one. 8. Average angles of y-type that are mostly found in hilly village are 175, 113, 72. Angle differences from each spot are 62 and 41 degree. It is assumed that 39 degree is a slope of least effort to walk. 9. 4 way of branch-roads have not only "＋" type but various types of K, Y and Y, Y and y, T and y and a foot of bird. 10. It is assumed that multi-way of branch-roads, mostly found on the middle and bottom of the hilly slope, has naturally formed to connect up and down, left and right.and right.

• 한국자기공명학회논문지
• /
• 제7권2호
• /
• pp.68-73
• /
• 2003

Proton magic angle spinning spectra and thermogravimetric analysis data of poly(vinyl butylal) with water in it indicate water contents in the poly(vinyl butylal) samples were reduced during magic angle spinning. Our observation implies that the centrifugal force on the samples due to magic angle spinning cannot be neglected, especially on inhomogeneous and soft samples like poly(vinyl butylal) we tested in this work.

• 한국인터넷방송통신학회논문지
• /
• 제18권2호
• /
• pp.177-184
• /
• 2018

본 논문에서는 $1{\times}6$ 배열 패치 안테나의 복사기 구조와 급전선 브랜치의 각도를 변화시켜 안테나의 특성을 분석하였다. 첫 번째로 복사기 구조를 기존 직사각형 패치를 육각형 패치, 삼각형 패치로 변경하였다. 두 번째로 급전선 브랜치의 각도를 $5^{\circ}$, $10^{\circ}$, $15^{\circ}$, $20^{\circ}$ 로 변화를 주었다. 브랜치 각도를 $10^{\circ}$로 꺾을 경우 측정된 10dB 주파수 대역은 23.38GHz-24.19GHz이고 대역폭은 810MHz이다. 제작된 안테나는 24.05GHz에서 9.65-10.06dBi 이득을 갖는다. 메인로브의 빔폭은 $12^{\circ}$이고, 안테나 크기는 $70{\times}36mm^2$이다. 직사각형 패치 외에 다른 모양의 패치를 사용해도 기존 성능을 유지할 수 있으며, 급전선 브랜치를 다양한 각도로 변화시킴으로 배열 안테나 제작에 있어 기판의 크기를 줄이고 제작상에 다양성에 기여할 수 있음을 확인했다.

• 한국세라믹학회지
• /
• 제56권5호
• /
• pp.461-467
• /
• 2019

Ink-jet printing technology, which utilizes a digitalized design to print fine ink directly on a substrate, has been of interest in various industries due to its high efficiency and adaptability to various materials. Recently, active attempts have been made to apply ceramic materials having excellent heat resistance, light resistance, and chemical resistance to the ink-jet printing process. In this study, ceramic ink was synthesized by combining ceramic pigments with UV curable polymer. 3D printability at various contact angles between ceramic ink and substrate was analyzed in detail. Rheological properties of the synthesized ceramic ink were optimized to meet the requirements of the ink-jet printing process, and the contact angle of UV curable ceramic ink was controlled through surface treatment of the substrate. The potential for additive manufacturing of ceramic material using ink-jet printing was investigated by analyzing the effect of contact angle control on ceramic ink droplets and their 3D printability.

• Smart Structures and Systems
• /
• 제22권3호
• /
• pp.335-340
• /
• 2018

The behavior of concrete slabs in composite beam with C and L shaped angle shear connectors has been studied in this paper. These two types of angle shear connectors' instalment have been commonly utilized. In this study, the finite element (FE) analysis and soft computing method have been used both to present the shear connectors' push out tests and providing data results used later in soft computing method. The current study has been performed to present the aforementioned shear connectors' behavior based on the variable factors aiming the study of diverse factors' effects on C and L shaped angle in shear connectors. ANFIS (Adaptive Neuro Fuzzy Inference System), has been manipulated in providing the effective parameters in shear strength forecasting by providing input-data comprising: height, length, thickness of shear connectors together with concrete strength and the respective slip of shear connectors. ANFIS has been also used to identify the predominant parameters influencing the shear strength forecast in C and L formed angle shear connectors.

• Journal of Electrical Engineering and Technology
• /
• 제8권4호
• /
• pp.863-871
• /
• 2013

Control of pitch angle of turbine blades is among the controlling methods in the wind turbines; this measure is taken for managing mechanical power generated by wind turbine in different wind velocities. Taking into account the high significance of the power generated by wind turbine and due to the fact that better performance of pitch angle is followed by better quality of turbine-generated power, it is therefore crucially important to optimize the performance of this controller. In the current paper, a PI controller is primarily used to control the pitch angle, and then another controller is designed and replaces PI controller through applying a new strategy i.e. alternating two ADALINE neural networks. According to simulation results, performance of controlling system improves in terms of response speed, response ripple, and ultimately, steady tracing error. The highly significant feature of the proposed intelligent controller is the considerable stability against variations of wind velocity and system parameters.

• Steel and Composite Structures
• /
• 제21권4호
• /
• pp.883-919
• /
• 2016

In this research, buckling analysis of an embedded laminated composite plate is investigated. The elastic medium is simulated with spring constant of Winkler medium and shear layer. With considering higher order shear deformation theory (Reddy), the total potential energy of structure is calculated. Using Principle of Virtual Work, the constitutive equations are obtained. The analytical solution is performed in order to obtain the buckling loads. A detailed parametric study is conducted to elucidate the influences of the layer numbers, orientation angle of layers, geometrical parameters, elastic medium and type of load on the buckling load of the system. Results depict that the highest buckling load is related to the structure with angle-ply orientation type and with increasing the angle up to 45 degrees, the buckling load increases.

• Structural Engineering and Mechanics
• /
• 제81권4호
• /
• pp.493-502
• /
• 2022

Shear lag phenomenon has long been considered in numerous structural codes; however, the AISC provisions have now no longer proposed any unique equation to calculate the shear lag ratio in bolted connections for angles in general. It is noticeable that, however, codes used in this case are largely conservative and need to be amended. A parametric study consisting of 27 angle sections with equal legs and different with bolted connections was performed to investigate the effects of shear lag on the ultimate tensile capacity of angle members. The main parameters were: steel grade, connection length and eccentricity from the center of the plate, as well as the number of rows of bolts parallel to the applied force. The test results were compared with the predictions of the classical 1-x/l law proposed by Mons and Chesen to investigate its application to quantify the effect of shear lag. A parametric study was performed using valid FE models that cover a wide range of parameters. Finally, based on the numerical results, design considerations were proposed to quantify the effect of shear lag on the ultimate tensile capacity of the tensile members.

• 설비공학논문집
• /
• 제13권5호
• /
• pp.356-367
• /
• 2001

A numerical analysis on branch type sparger in drain tank for depressurization is performed to investigate the flow characteristics due to the change of design factor. As the result of this study, sparger\\`s flow resistance coefficient(K) is 3.53 at the present design condition when engineering margin for surface roughness is considered as 20%, and flow ratio into branch pipe ($Q_s/Q_i$) is 0.41. The correlation for calculating flow resistance coefficients as design factor is presented. Flow resistance coefficient is increased as section area ratio of branch pipe for main pipe and outlet nozzle diameter of main pipe decreasing, but the effects of branch angle and inlet flow rate of main pipe are small. As the change rate of ($Q_s/Q_i$)becomes larger, the change rate of flow resistance coefficient increases. The rate of pressure loss has the largest change as section area ratio changing. The condition of maximum flow resistance in sparger is when the outlet nozzle diameter ratio of main pipe ($D_e/D_i$) is 0.167, the section area ratio ($A_s/A_i$) is 0.1 and the branch angle ($\alpha$) is 55^{\circ}$.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권3호
• /
• pp.76-81
• /
• 2002

In order to study the fatigue crack and retardation mechanism in variable loading, the effects of crack tip branching in crack growth retardation were examined. The characteristics of crack tip branching behavior were considered with respect to microstructure and crack tip branching angle was examined. Crack tip branching was observed along the grain boundary of finite and pearlite structure. It was found that the branching angle ranges from 25 to 53 degrees. Using the finite element method, the variable of crack driving farce to branching angle was examined. The effective crack driving farce (K$\_$eff/) decreased as the branching angle increased. The rate of decrease was 33% for kinked type and 29% for forked one. It was confirmed that the effect of crack tip branching is a very important factor in crack growth retardation. Therefore, crack branching effect should be considered in building the hypothetical model to predict crack growth retardation.