• The Journal of the Acoustical Society of Korea
• /
• v.31 no.1
• /
• pp.11-18
• /
• 2012

In this paper, the occurrence of a stopband phenomenon when an acoustic wave propagates through periodically corrugated ducts is discussed using theoretical and BEM analyses. A 2-D duct with sinusoidally corrugated upper and lower walls is considered. When the magnitude of the sinusoidal corrugation is sufficiently small compared to the duct's height, the wave equation is solved with the multiple scaling perturbation method. Then stopbands for Bragg and non-Bragg resonances are computed from the condition where frequency becomes a complex number. A 2-D BEM analysis is performed to compute insertion loss of the duct, and stopbands are confirmed as predicted by analytical analysis.

• Journal of the Korean Ceramic Society
• /
• v.38 no.11
• /
• pp.980-986
• /
• 2001

Bragg reflector type FBAR was fabricated on the Si(100) substrate. We measured a frequency response of the resonator at 5.2 GHz and analyzed it by numerical calculation considering actual acoustic losses of each layer in the structure. We fabricated nine layer Bragg reflector of W-SiO$_2$pairs using r.f. sputtering method and fabricated AlN piezoelectric and Al electrodes using pulsed dc sputtering. The return loss(S$_{11}$) of the fabricated Bragg reflector type FBAR was 12 dB at 5.38 GHz and the series resonance frequency(f$_{s}$) was 5.376 GHz and the parallel resonance frequency(f$_{p}$) was 5.3865 GHz. Effective electro-mechanical coupling constant (K$_{eff{^2}}$) and Quality factors(Q$_{s}$), the Figures of Merit of the resonator, were about 0.48% and 411, respectively. We extracted acoustic parameters of AlN piezoelectric and reflection coefficient of the Bragg reflector by numerical calculation. We could know that material acoustic impedance and wave velocity of AlN piezoelectric decreased for intrinsic value and the electromechanical coupling constant(K$_2$) value was very low owing to the poor quality of the AlN piezoelectric. Reflection coefficient of Bragg reflector was 0.99966 and reflection band was very wide from 2.5 to 9.5 GHz.

• Korean Journal of Optics and Photonics
• /
• v.23 no.5
• /
• pp.227-232
• /
• 2012

A large-signal time-domain model is implemented to analyze an FG-LD (Fiber Grating Laser Diode) in which a reflective laser diode is hybrid-integrated with a fiber Bragg grating (FBG). When the length of the externally integrated resonator is 8 mm, in which the effective FBG length of 2.1 mm is included, a static frequency chirp of 0.44 GHz and a dynamic frequency chirp of 6.4 GHz are observed. In addition, it is also observed that the eye of the 10Gbps NRZ signal is well open. The FG-LD is expected to be a cost-effective solution for a 10Gbps-class single wavelength laser covering a span of 50 km range.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.5
• /
• pp.513-516
• /
• 2011

The dynamic behavior of a small wind-turbine blade was analyzed experimentally. Arrays of fiber Bragg-Grating (FBG) sensors attached along the blade were used to measure the strains of the blade surface. An impact test was performed to estimate the resonance frequencies of the fundamental and higher modes of the cantilever blade system developed for this study. The results were similar to the results for conventional strain gages. However, FBG sensors could sense modes that strain gauges could not sense. The strains obtained from the FBG sensor array were used to estimate displacement-mode shapes of the blade.

• Korean Journal of Optics and Photonics
• /
• v.23 no.5
• /
• pp.211-216
• /
• 2012

We report a resonance fiber Bragg sensor interrogation based on a Fourier domain mode-locking (FDML) laser. The FDML laser is constructed based on a conventional ring laser cavity configuration with fiber Fabry-Perot tunable filter (FFP-TF). There are two sensor parts which are composed with two FBGs inside the laser cavity. Each sensor part provides a separate laser cavity for the FDML laser. The resonance frequencies of the laser cavities are 46.687 kHz and 44.340 kHz, respectively. We applied a static and a dynamic strain on the FBG sensor system. The slope coefficients of the measured relative wavelength shift and relative time interval from the static strain are found to be $0.61pm/{\mu}{\epsilon}$ and $0.8ns/{\mu}{\epsilon}$, respectively.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2003.12a
• /
• pp.54-58
• /
• 2003

본 연구에서는 $SiO_2/Si$ 기판 위에 $1.1\mu\textrm{m}$ 두께의 ZRO 압전층을 다양한 조건 하에서 증착하고, 그 특성을 분석하고, film bulk acoustic wave resonator 소자에 적용하였다. 증착조건으로 $Ar/O_2$ 유량비를 25-75 %로 변화시켰으며, working pressure는 3~15 mtorr, RF power는 213~300 W로 변화시켜가며 실험을 하였다. 증착된 ZnO 박막은 XRD (X-ray diffractomter)와 SEM (scanning electron microscopy)을 통해 특성이 분석되었다. LFE모드의 BAW 공진기는 $50\times50\mu\textrm{m}^2$ 공진면적을 가지며, $W/SiO_2$의 5층 Bragg reflector와 상하부 전극으로 $1800{\AA}$의 Al-3% Cu, 그리고 $1.4\mu\textrm{m}$ 두께의 ZnO 압전박막으로 구성되었다. 2.128-2.151 GHz 주파수 사이에서 공진이 일어났으며, Q factor는 400으로 측정되었다.

• Korean Journal of Optics and Photonics
• /
• v.17 no.6
• /
• pp.544-547
• /
• 2006

A time-domain modeling approach is used to study characteristics of a widely tunable coupled-ring reflector (CRR) laser diode(LD). The CRR consists of a bus waveguide and two coupled ring resonators coupled to the bus without resorting to distributed Bragg grating structure. The tuning range can be a few tens of nanometers with a side mode suppression ratio exceeding 35dB through the adjustment of currents into the phase control sections in the rings. The CRR laser diode has long effective cavity length compared to conventional laser diodes. Accordingly, a broad additional resonance peak in the amplitude modulation characteristics is observed between 20 to 30 GHz, implying the extension of amplitude modulation bandwidth.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.10
• /
• pp.256-263
• /
• 2014

We have designed and made three kinds of FBG(Fiber Bragg Grating) Acoustic Transducer using Hopper type WDM on the use of recently developed FBG in Korea. The newly designed three kinds of FBG Acoustic Transducer using Hopper type WDM have an excellent merit of practical use with simple structure of sensors arm as well as the merit with existing fiber sensors. It was possible to detect sound waves in the range of 10 Hz to 18 kHz through the newly designed three kinds of FBG Acoustic Transducer and also, possible to detect its signal within the maximum range of 8.6 m by the use of most suitable resonance condition of the transducer. Especially, we can expect the utilization of low-frequency signal detection instead of existing acoustic sensor in the environment of electric noise and inferior condition. Furthermore, they can be developed as the high-sensibility and multi-point signal detection system through the sensor array system.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.11
• /
• pp.156-163
• /
• 2015

In the using of FBG(Fiber Bragg Grating) developed in home land, we designed and manufactured united FBG acoustic transducers the first in Korea. they are being applied to multi-point signal detection of FBG Hydrophone used Hopper WDM(national patent NO 10-1502954) in the underwater. On united FBG transducers manufactured, we made an demonstrated on respective frequency response peculiarities in the underwater and analyzed the special characters. As the experimental result on frequency response peculiarities, we made it possible underwater acoustic detection on united FBG acoustic transducers type to maximum 30Hz~2.5KHz. it's the optimum conditions of 1.2KHz frequency in detection. And for the purpose of realization on multi-point signal detection on wide scope in the underwater, in the using of WDM(Wavelength Division Multiplexing) method and passive band-pass filter system, established arrays system and succeeded in multi-point underwater acoustic signal detection to the frequency 200Hz~1.3KHz out of the two united type FBG transducers. Additionally, it would be possible directivity detection for the object of its source as the intensity of detection signal varies with the sound source's direction and angle. From now on we prepared a new moment on the practical use study on FBG hydrophone in the future.

• Korean Journal of Optics and Photonics
• /
• v.21 no.5
• /
• pp.185-189
• /
• 2010

We demonstrate a single-frequency wavelength tunable erbium-doped fiber (EDF) ring laser. We used an unpumped-EDF as a saturable-absorber in order to obtain a stable single-frequency with a narrow-linewidth single-polarization mode in the ring cavity. The lasing wavelength was controlled by using bending-induced strain, such as tension and compression strain corresponding to the bending direction, applied to the fiber gratings. The fiber laser exhibited an output power of -1.85 dBm at a wavelength of 1540.72 nm for a pumping power of ~400 mW. An extinction ratio was measured to be more than 60 dB. The proposed tunable fiber laser maintains nearly the same output power while its lasing wavelength is controlled over in a wavelength range of 5 nm.