• Analytical Science and Technology
• /
• v.29 no.3
• /
• pp.136-141
• /
• 2016

In the present study, the distribution of glass particles inside 10 patrol cars of Chungnam Province has been studied. The target seats were front seats (driver’s seat, passenger’s seat) and the back seat. The target areas were the bottom of the seat (seat contacting buttocks, back of the seat, and the corner of the seat (the bottom and back attached part)). The target areas were tape lifted with an adhesive tape. The glass particles adhering to the adhesive tape were examined and counted under a stereomicroscope. The total number of glass particles found was 679. Among them, 471 (driver’s seat 293, passenger seat 178) were collected from front seats, which are usually occupied by police officers. The majority of glass particles were under 0.49 mm size. The results show that the majority of glass particles can be found on the front seats, rather than on the back seat. There is a high probability that glass particles found on the front seat adhere to police officers, so that to get further transferred to the convict upon physical contact (secondary transfer). Thus, there is a risk of misinterpretation of the value of glass evidence in the course of forensic examinations. Hence, a separate method to prevent cross contamination has to be prepared by police authorities as soon as possible.

• Current Research on Agriculture and Life Sciences
• /
• v.19
• /
• pp.23-29
• /
• 2001

This study was carried out to develop a seedling raising method without nursery soils in automatic raising facility of rice seedlings for machine transplanting. Pre-germinated seeds were sowed on the seed trays with three different seats such as paper seat, corrugated board, and polyethylene film instead of nursery soils. The growth characteristics of the seedlings for 20 days after sowing were compared with that of a conventional standard raising method with nursery soils. There was no difference in plant height of 10-day old seedlings among the different nursery methods, but the plant height of seedlings grown for 15 days after sowing in the trays with fivefold newspaper and nursery soils was significantly taller than those on other nursery conditions. Dry weight of seedlings grown in the tray with fivefold newspaper bottom was heavier than those in nursery trays with a corrugated board and a piece of polyethylene film. The seedlings grown in a nursery tray with fivefold newspaper showed better seedling quality and root-mat formation compared with the other nursery trays. This result suggests that the healthy seedlings for machine transplanting can be raised in the paper-sheet tray without nursery soils. The labour hours and cost required for the soil-free method using paper was reduced by about 49.3% and 26.6%, respectively, compared with the semi-adult seedling on nursery soils.

• International Journal of Concrete Structures and Materials
• /
• v.7 no.1
• /
• pp.51-59
• /
• 2013

The use of light-gauge steel framing in low-rise commercial and industrial building construction has experienced a significant increase in recent years. In such construction, the wall framing is an assembly of cold-formed steel (CFS) studs held between top and bottom CFS tracks. Current construction methods utilize heavy hot-rolled steel sections, such as steel angles or hollow structural section tubes, to transfer the load from the end seats of the floor joist and/or from the load-bearing wall studs of the stories above to the supporting load-bearing wall below. The use of hot rolled steel elements results in significant increase in construction cost and time. Such heavy steel elements would be unnecessary if the concrete slab thickening on top of the CFS wall can be made to act compositely with the CFS track. Composite action can be achieved by attaching stand-off screws to the track and encapsulating the screw shank in the deck concrete. A series of experimental studies were performed on full-scale test specimens representing concrete/CFS flexural elements under gravity loads. The studies were designed to investigate the structural performance of concrete/CFS simple beams and concrete/CFS continuous headers. The results indicate that concrete/CFS composite flexural elements are feasible and their structural behavior can be modeled with reasonable accuracy.

• Journal of the Korea Safety Management & Science
• /
• v.13 no.2
• /
• pp.83-90
• /
• 2011

It has been very important to have an exact evaluation for risk factors in order to prevent WMSDs(Work-related Musculoskeletal Disorders). However, most WMSDs evaluation methods have always been some problems of possibilities associated with subjective evaluation. Therefore, this study tried to conduct a sort of usability analysis on three major evaluation methods(OWAS, RULA, REBA). Specifically, major subjects in the study consisted of three parts as follows; comparison of the results between experienced and inexperienced observers, analysis for the consistency of the results in terms of different evaluation times, and analysis for the consistency of the results in terms of different job characteristics(based on the part of the automobile). The results of the study were summarized as follows; 1) There was statistically significant difference of the results by RULA and by REBA between experienced and inexperienced observers. This might be due to the fact that experienced observers have had better ability to detect the important working posture during evaluation. However, the results by OWAS did not give any significantly different results between experienced and inexperienced observers, 2) All three checklists applied by experienced subjects did not show any single result significantly different in terms of different evaluation times. This might have to do with high intra-observer reliability from some of previous studies, 3) The five parts of an automobile were selected as five major jobs with different job characteristics in the automobile industry. Specifically, they were door part, front part(hood, etc.), inside part(dash board, seats, etc.), rear part(trunk etc.), and bottom part. All three methods did not show any significant differences for the results from each observers. Further study on this subject would eventually provide a sophisticated evaluating guidelines for WMSDs regarding determination of observer-specific evaluation, identification of repetitive number of evaluations for stable results for each checklist, determination of job-specific evaluation methods, and so on.