• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.424-428
• /
• 2012

Air-breathing Propulsion System is one of the promising propulsion systems because of low cost, easy storage, compactness and simplicity. A study of gas generator propellant for air-breathing propulsion system was performed in this paper. Amorphous Boron Powder was applied in propellant with various kinds of additives to determine combustion characteristics. And boron beads were made to apply them to the propellant. Combustion characteristics of propellant using amorphous boron powder and boron beads was compared.

• Journal of Welding and Joining
• /
• v.29 no.1
• /
• pp.107-114
• /
• 2011

CP steel was developed to reduce the weight and increase the strength of car body. When it was welded using state-of-the-art disk laser welding, the effected of boron on the microstructure and hardness were investigated. Welding power was fixed at 3.5kW and welding speeds were 4,8 and 12m/min. Full penetration occurred in welding speed of 12m/min and weld bead was almost unchanged with boron contents. But the welding speed increased, the upper and lower bead were narrowed. In a welding speed of more than 8m/min, underfill defects were formed on the bead bottom. The hardness of weld zone was somewhat fluctuation in fusion zone and HAZ showed the highest hardness values. The hardness of each region showed little change with the boron contents, and softening phenomenon occurred in the HAZ near the base metal regardless of the boron contents.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.12-18
• /
• 2014

A study of gas generator Fuel-Rich propellant for air-breathing propulsion system was performed in this paper. General solid propellant comprises a mean of 60% or more oxidizing agents. but, to develop the fuel-rich solid propellant increased the content of the metal fuel and reduced the content of the oxidizing agents by approximately 30%. Very high amount of heat per volume of fuel into the metal having the Boron was used. Amorphous Boron Powder was applied to propellant as beads type and it allowed to design more amount of metal fuel in the fuel-rich propellant. And the Combustion characteristics and properties of fuel-rich solid propellant according to the Boron-bead sizes were confirmed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.4
• /
• pp.26-32
• /
• 2014

The combustion characteristics of Boron-beads to improve the energy density of gas generator has been investigated in accordance with diameter of beads and their composition. In this paper, electrically heated tungsten sheet and visualized furnace are applied to measure ignition temperature and burning time of bead respectively. The results proposes ignition temperature between 720~800 K and burning time proportional to bead diameter. Also a ignition delay of boron particle is detected through the temperature and radiation intensity measurements.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.3
• /
• pp.97-102
• /
• 2009

The use of deep water as drinking water is greatly limited of significant concentration of boron in sea water. Boron is reported to be toxic for human and plants. Some of possible methods are available to remove boron. The polymeric resins were synthesized to remove the boron from the sea water. The resin was characterized with IR analysis and the morphology was discussed with SEM images. To assess boron removal capacity of the resin, it was distributed in three different bead size i.e., 0.25mm, 0.5mm and 1.0mm. The removal behavior of this resin was examined under the batch experiments.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.1
• /
• pp.12-19
• /
• 2022

The propellants used in the gas generator of the ducted rocket are fuel-rich propellants, which contain an excessive amount of metal fuel and a small amount of oxidizing agent compared to general solid rocket propellants. In this paper, boron powder and MgAl(Magnesium-Aluminium alloy) were applied to produce fuel-rich propellants. The optimum formulation was determined by characterizing these metal fuel-rich propellants. Analysis of combustion products in the gas generators confirmed that the fuel-rich propellants containing fine boron powder itself instead of boron-bead could be useful in gas generators.

• Laser Solutions
• /
• v.15 no.1
• /
• pp.1-5
• /
• 2012

Recently ultra high strength steels(UHSS) has been widely applied to the structural or safety components in the automotive industry. Specially, hot stamping boron steel 22MnB5 has shown the crash-resistant characteristics when applying to bumpers and pillars. Lap joint Laser welding of the hot stamped and die quenched sheets of Boron steel was carried out using 3kW Nd/YAG laser. The appropriate Lap joint laser welding conditions were founded separately for four lap joint combinations. The lower sheest is a hot stamped sheet in common and the upper sheet is selected among the hot stamped steel and high strength steels such as SPCC, 370MPa, and 590MPa grade high strength steels. Cross bead sections and local hardening and softening were observed as well as tensile-shear test results.

• Laser Solutions
• /
• v.13 no.4
• /
• pp.1-6
• /
• 2010

Recently the use of ultra high strength steels (UHSS) in structural and safety component is rapidly increasing in the automotive industry. For example, 1.5GPa grade hot stamping with die-quenching of boron steel 22MnB5 could apply crash-resistant parts such as bumpers and pillars. The development of laser welding process of hot stamping steels, fundamental bead-on-plate welding and lap joint welding test were carried out using 3kW Nd:YAG laser. Local hardening & HAZ softening occurred in hot stamping steel as a result of metallurgical change caused by the welding heat input in the Nd:YAG laser welding process. The size of soft zones in the hot stamping steel was related to the welding heat input, being smaller at high speeds which generated a smaller heat input. Also in the case of lap joint design structure, same welded characteristics were shown. The HAZ softening degree was controlled to ensure the joint strength.

• Analytical Science and Technology
• /
• v.11 no.2
• /
• pp.112-119
• /
• 1998

A Siemens SemiQuant (SSQ) 3000 program, a precalibrated 'standardless' analytical program handling up to 90 elements, was evaluated for the fast analysis of various types of reference materials using a wavelength dispersive X-ray spectrometer. Various types of standard reference materials such as metal discs, metal chips, and geological materials in powder form were analysed and it took 23 minutes of measuring time for 75 elements. Measurements of geological reference materials using different sampling methods were carried out and their data were interactively evaluated. The analysis of materials of a known matrix concentration such as stainless steels provided higher precision value compared to totally unknown samples. The analyses of materials prepared as pressed pellets or fused glass beads provided higher precision values compared to the measurement of loose powders with a foil on the sample surface and helium operation, though their sampling procedures were more complicate and took more time. Since very light elements such as boron, carbon, and oxygen have a strong influence on the matrix effects and also on the calculation of effective matrix corrections, the rhodium Compton check was applied to verify the reliability of the defined light element concentrations of light matrix materials and the defined major sample compounds. Failure of defining correct matrix resulted in an unoptimized matrix correction and therefore in the wrong calculation of the element concentration.