• 한국정밀공학회지
• /
• 제21권1호
• /
• pp.140-148
• /
• 2004

A novel rapid prototyping (RP) process, a full-automated transfer type variable lamination manufacturing process (Full-automated VLM-ST) has been developed. In the full-automated VLM-ST process, a vacuum chuck and a rectilinear motion system transfer the EPS foam material in the form of the plate with two pilot holes to the rotary supporting stage. The supplied material is then cut into an automated unit shape layer (AUSL) with a desired width, a desired length, a desired slope on the side surface, and a pair of reference shapes, which is called the guide shape (GS)’, including two pilot holes in accordance with CAD data through cutting in two steps using a four-axis synchronized hotwire cutter. Then, each AUSL is stacked by setting each AUSL with two pilot holes in the building plate with two pilot pins, and subsequently, adhesive is applied onto the top surface of the stacked AUSL by a bonding roller and pressure is simultaneously given to the bottom surface of the stacked AUSL. Finally, three-dimensional shapes are rapidly and automatically fabricated. This paper describes the method to generate guide shapes in AUSL data for the full-automated VLM-ST process. In order to examine the applicability of the method to generate guide shapes, three-dimensional shapes, such as a piston shape and a human head shape, are fabricated from the full-automated VLM-ST apparatus.

• 한국재료학회지
• /
• 제26권12호
• /
• pp.751-756
• /
• 2016

Graphite was diffusion-bonded by hot-pressing to W-25Re alloy using a Ti interlayer. For the joining, a uniaxial pressure of 25 MPa was applied at $1600^{\circ}C$ for 2 hrs in an argon atmosphere with a heating rate of $10^{\circ}C\;min^{-1}$. The interfacial microstructure and elemental distribution of the W-25Re/Ti/Graphite joints were analyzed by scanning electron microscopy (SEM). Hot-pressed joints appeared to form a stable interlayer without any micro-cracking, pores, or defects. To investigate the high-temperature stability of the W-25Re/Ti/Graphite joint, an oxy-acetylene torch test was conducted for 30 seconds with oxygen and acetylene at a 1.3:1 ratio. Cross-sectional analysis of the joint was performed to compare the thickness of the oxide layer and its chemical composition. The thickness of W-25Re changed from 250 to $20{\mu}m$. In the elemental analysis, a high fraction of rhenium was detected at the surface oxidation layer of W-25Re, while the W-25Re matrix was found to maintain the initial weight ratio. Tungsten was first reacted with oxygen at a torch temperature over $2500^{\circ}C$ to form a tungsten oxide layer on the surface of W-25Re. Then, the remaining rhenium was subsequently reacted with oxygen to form rhenium oxide. The interfacial microstructure of the Ti-containing interlayer was stable after the torch test at a temperature over $2500^{\circ}C$.

• 한국염색가공학회지
• /
• 제1권1호
• /
• pp.7-18
• /
• 1989

The distinguishing characteristic of the glow discharge is that chemical reaction induced by partially ionized gases are limited only to the substrate surface. Most studies have been done on the plasma etching and polymerization. The graft polymerization in vapour phase by cold plasma has been rarely investigated. In this study the system of tub3ar reaction chamber with capacitively coupled electrode of alternative current of 60 Hz was employed for the graft polymerization. The graft polymerization of Acylic Acid(AA) onto the poly (ethylene terephthalate) (PET) was carried out by treatment of PET film and fabric by cold plasma (glow discharge of argon gas), followed by the supply of AA vapour. The graft yield was about 1 wt%. The surface property was determined by contact angle, the surface tension was evaluated by zisman’s plot and equation of surface tension mesurement. The results were as follows: 1. In order to obtain lower contact angle, it was effective to avoid the vicinity of electrodes for a setting position of substrate. 2. Contact angle affected on the monomer pressure and its duration of exposure to the acid vapour. 3. Polymer radical formation was influenced by the changes of the value of current density and plasma treatment time. 4. Total surface tension of plasma grafted PET film increased. With an increase in the carboxylic acid content, the dispersion force decreased, while, the polar force and hydrogen bonding force increased. 5. The contact angle decreased from $75^\circ$ to around $30^\circ$ by plasma grafting. There was no ageing effect on the contact angle after 4 months.

• Current Photovoltaic Research
• /
• 제2권4호
• /
• pp.168-172
• /
• 2014

Under concentrated illuminations, the solar cells show higher efficiencies mainly due to an increase of the open circuit voltage. In this study, InGaP/InGaAs/Ge triple-junction solar cells have been grown by a low pressure metalorganic chemical vapor deposition. Photovoltaic characteristics of the fabricated solar cells are investigated with a class A solar simulator under concentrated illuminations from 1 to 100 suns. Ideally, the open circuit voltage should increase with the current level when maintained at the same temperature. However, the fabricated solar cells show degraded open circuit voltages under high concentrations around 100 suns. This means that the heat sink design is not optimized to keep the cell temperature at $25^{\circ}C$. To demonstrate the thermal degradation, changes of the device performance are investigated with different bonding conditions and heat sink materials.

• 터널과지하공간
• /
• 제9권3호
• /
• pp.204-213
• /
• 1999

터널 굴착 방법 중 NATM에서는 숏크리트, 록볼트, 강지보재 등이 주요 지보재로 사용되고 있다. 강지보재 중에서 격자지보(Lattice Girder)라 불리는새로운 지보재가유럽에서 개발되어 기존의 H형강 지보재를 대체하여 사용되고 있다. 격자지보는 강봉을 삼각형태로 용접하여 만든 것으로 가벼워 시공이 빠르고, 또한 숏크리트와의 결합특성이 좋아 앞으로 NATM 터널에 널리 사용될 전망이다. 본 연구에서는 국내 터널에 있어서 격자지보의 현장 적용성을 평가하기 위하여 대단면 고속철도 터널에서 현장시험시공을 실시하였으며, 기존의 H형강 지보재와 비교분석 하였다. 현장시험 결과 격자지보는 터널굴착 후의 지반하중을 충분히 지지할 수 있으며 지반변위를 효과적으로 억제할 수 있음을 알 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제22권2호
• /
• pp.265-273
• /
• 2011

HC-SCR was conducted using Fe/ZSM5 catalyst coated over 200 cpi cordierite in the conditions of atomspheric pressure and $200^{\circ}C-500^{\circ}C$. Among the tested hydrocarbon reductants, isobutane (i-$C_4H_{10}$) showed the highest de-$NO_x$ yield of 69% at $320^{\circ}C$ with the mole ratio of reductant/$NO_x$ =1.0. De-$NO_x$ yield resulted by the change of alkane reductant was increased as the carbon number of alkane reductant was increased. The order of increase of de-$NO_x$ yield was proportional to the order of decrease of bonding energy between C and H of reductant, where the H abstraction step from alkane molecule could be the rate controlling step of HC-SCR.

• 한국환경과학회지
• /
• 제6권1호
• /
• pp.75-88
• /
• 1997

The rates of photodegradation, reactivities, and mechanisms of photooxidation for the aqueous solution containing with halogen derivatives of aliphatic hydrocarbons have been discussed with respect to the kinds of photocatalysts, concentration of photocatalytlc suspensions, strength of radiant power, time of illumination, changes of pH of substrate solution, wavelength of radiation, and pressure of oxygen gas saturated In the solution. These aqueous solutions suspended with 0.5 $gL^{-1}$ $TiO_2$ powder have been photodecomposed in the range of 100 and 93.8% per 1 hour if it is illuminated with wavelength (λ $\geq$ 300nm) produced from Xe-lamp(450W). The photocatalytic abilities have been increased In the order of $Fe_2O_3$ < CdS < $CeO_2$ < Y_2O_3$ <$TiO_2$, and rates of photodegradation for the solution have maldmum values in the condition of pH 6 ~ 8 and 3 psi-$O_2$ gL^{-1}$. These rates for the Photoolddation Per 1 hour were dependent on the size of molecular weight and chemical bonding for organic halogen compounds and the rates of photodegadation were increased in the order of $C_2H_5Br$ < CH_2Br_2$ < C_5H_11Cl C_2H_4Cl_2$ < tracts-$C_2H_2Cl_2$ < cis-C_2H_2Cl_2$ The T_{1/2}$ and t99% for these solutions were 5~21 and 40~90 minutes. respectively, and these values were coincided with Initial reaction kinetics(ro). It was found that reaction of photodegradation has the pseudo first-order kinetics controlled by the amount of $h^+_{VB}$ diffused from a surface of photocatalysts.

• 콘크리트학회논문집
• /
• 제21권6호
• /
• pp.781-788
• /
• 2009

강-콘크리트 계면의 성질을 대표하는 부착강도, 부착 및 비부착 마찰계수, 부착 및 비부착 마찰계수의 연화영역에서 잔류량의 크기, 모드 I 파괴에너지, 부착 및 비부착 모드 II 파괴에너지, 파괴포락선의 형상계수를 포함한 총 9개 계면상수의 값을 계면거동실험결과와 파괴포락선의 기하학적 형상 및 구성모델을 이용하는 민감도 해석을 통해 결정하였다. 계면의 거동이 계면의 부착상태뿐만 아니라 계면법선방향 응력의 방향과 크기에 따라 매우 민감하게 작용하므로 계면상수 값의 결정에서는 이러한 구속압의 크기와 부착 및 비부착 계면조건을 고려하였다. 강재판 사이에 콘크리트가 타설된 강-콘크리트 계면실험체의 거동해석을 위한 계면유한요소해석을 결정된 계면상수를 적용하여 수행하였으며 실험결과와의 비교를 통해 상수값의 적정성을 검토하였다.

• Korean Chemical Engineering Research
• /
• 제54권6호
• /
• pp.830-837
• /
• 2016

그라파이트 폼의 압축강도를 향상시키기 위하여 메조페이스 핏치를 공기분위기에서 산화안정화 한 후 다양한 불소 부분압으로 처리하였다. 불소화 처리된 메조페이스 핏치의 불소/탄소 표면화학 조성은 불소 부분압에 따라서 약 23.75%~61.48%의 범위를 가진다. 불소화 메조페이스 핏치기반 그라파이트 폼의 압축강도는 겉보기 밀도의 증가에 비례하여 증가되었다. 불소/탄소 표면화학 조성이 35.93%의 값을 갖는 메조페이스 핏치로부터 제조된 그라파이트 폼의 압축강도는 최대 $2.93{\pm}0.06MPa$의 값을 보여 주었으며, 이 값은 미처리된 메조페이스 핏치로부터 제조된 그라파이트 폼과 비교하여 27.95% 증가되었다. 이러한 결과는 표면에너지가 큰 불소 작용기로 인한 메조페이스 핏치간의 계면결합력이 그 압축강도를 증가시켰기 때문으로 여겨진다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.182-182
• /
• 1999

The chemisorption effect of CO on the Ni/Cu(001) surface was investigated using LEED(Low Energy Electron Diffraction) and EELS(Electron Energy Loss Spectrscopy0 under the UHV conditions. after mounting the Cu(001) single crystal in the UHV chamber (base pressure 1$\times$10-10Torr), a clean surface was obtained after a few cycles of repeated Ar+ ion sputtering and annealing at about 40$0^{\circ}C$. The epitaxial thin Ni films were formed on the Cu(001) by evaporation from 99.999% Ni block. The pseudomorphic growth and the orderness of the thin Ni films were monitored by c(2$^{\circ}C$2) LEED pattern. CO adlayers on Ni epitaxial thin films were prepared by dosing pure CO has through a leak valve. After CO adsorpton at room temperature, two pairs of peaks were observed by EELS, whose relative intensities are changed as the film thickness is varied and time is elapsed. These two pair of peaks are likely related to different bonding sites (-top and bridge sites) of C-Ni as well as C-O vibration. Experimental results and qualitative interpretation of the spectra wille be discussed. The possibility of using EELS in combination with probe species (CO) to investigate the nature of thin film growth is mentioned. We will report the experimental result of O2 dosage on Ni film and interaction of CO and O2.