• 접착 및 계면
• /
• 제24권1호
• /
• pp.36-40
• /
• 2023

반데르발스 물질이란 층간 결합이 약한 반데르발스 결합으로 이루어진 이차원 층상구조를 지닌 물질을 의미하며, 이러한 반데르발스 이차원 소재를 이용한 이종접합 구조 연구는 그래핀이 발견된 이후 꾸준히 연구되고 있다. 본 논문에서는 대기압 화학기상증착법을 통해 성장된 단층 단결정 MoSe₂를 기반으로하는 반데르발스 이종접합 트랜지스터 소자에 대해 보고한다. 최적화된 공정조건에서 성장된 MoSe₂는 원자수준의 결함이 존재하지 않는 것을 밝혔으며, 이를 이용한 트랜지스터 소자 또한 우수한 특성을 보인다는 것을 밝혀내었다.

• Journal of the Korean Wood Science and Technology
• /
• 제50권2호
• /
• pp.134-147
• /
• 2022

The objective of this study is to determine the effect of fiber direction arrangement and layer composition of hybrid bamboo laminate boards on the physical and mechanical properties. The raw material used was tali bamboo (Gigantochloa apus (J.A. & J.H. Schultes) Kurs) rope in the form of flat sheets (zephyr) and falcata veneer (Paraserianthes falcataria (L) Nielsen). Zephyr bamboo was arranged in three layers using water-based isocyanate polymer (WBPI) with a glue spread rate of 300 g/m². There were variations in the substitution of the core layer with falcata veneers (hybrid) as much as two layers and using a glue spread rate of 170 g/m². The laminated bamboo board was cold-pressed at a pressure of 22.2 kgf/cm² for 1 h, and the physical and mechanical properties were evaluated. The results showed that the arrangement of the fiber direction significantly affected the dimensional stability, modulus of rupture, modulus of elasticity, shear strength, and screw withdrawal strength. However, the composition of the layers had no significant effect on the physical and mechanical properties. The bonding quality of bamboo laminate boards with WBPI was considered to be quite good, as shown by the absence of delamination in all test samples. The bamboo hybrid laminate board can be an alternative based on the physical and mechanical properties that can meet laminated board standards.

• 수산해양기술연구
• /
• 제17권2호
• /
• pp.93-103
• /
• 1981

Si-Cr계 내열강 SUH3와 Cr-Ni계 stainless강 SUS 303 및 이들이 마찰용접재 SUH3-SUS303을 $1,060^{\circ}C$에서 용체화처리하고 다시 $700^{\circ}C$에서 10, 100시간 시효열처리한 각 시험편의 고온 피로강도에 대한 시효열처리의 효과를 알기 위하여 $700^{\circ}C$에서 고온 회전굽힘 피로시험을 하고 파약거동을 미시적으로 관찰하여 다음과 같은 결과를 얻었다. 1) SUH3재와 SUS303재의 최적마찰용접조건은 회전수 2420rpm, 마찰가압력 $8kg/mm^2$, 전 upset량 7mm(마찰가압시간 3sec, upset시간 2sec)이었다. 2) $700^{\circ}C$ 고온에서 장시간 이루어지는 고온피로시험에 있어, 용체화처리재의 S-N 곡선 경사부의 기울기가 가장 급하게 나타났다. 3) SUH3-SUS303 마찰용접재는 $1,060^{\circ}C$에서 1시간용체화 처리하고, $700^{\circ}C$에서 시효처리하는 경우 최적시효시간은 10시간이었다. 4) 10시간 시료재의 고온피로한도는 모재보다 SUH3은 75.4%, SUS303은 28.5% 높았으며, 용접재 SUH3-SUS303은 44.2% 정도 높았다. 100시간 시효재는 모재보다 SUH3은 64.91% SUS303은 30.4% 높았으며, SUH3-SUS303은 30.4% 높았으며, SUH3-SUS303은 36.6% 높았다. 5) 마찰용접재의 상온 및 고온의 피로파단은 모두 SUS303의 모재측에 발생하였으며, 용접면에서의 파단은 전혀 없었다. 6) SUS303재와 마찰용접재 SUH3-SUS303재의 크랙은 입내파양형이었으나 SUH3은 입계크랙의 전파로 파양한다.

• Journal of the Korean Wood Science and Technology
• /
• 제24권4호
• /
• pp.56-63
• /
• 1996

This study was to manufacture thinned wood of Larix leptolepis Gordon into Oriented Strand Board(OSB) with Urea-Formaldehyde Resin. The OSB was made of four kinds of strand in slenderness ratio 150 ; thickness $0.3{\pm}0.05mm$, $0.4{\pm}0.05mm$, $0.5{\pm}0.05mm$ and $0.6{\pm}0.05mm$, respectively length 45mm, 60mm, 75mm and 90mm. Target densities were 0.65gr/$cm^3$, 0.75gr/$cm^3$ and 0.85gr/$cm^3$. The stepwise 9 minutes-multi-pressing schedule in the maximum pressure 40kgf/$cm^2$, the minimum pressure 10kgf/$cm^2$ was applied for $400mm{\times}390mm{\times}12mm$ board at the temperature of $150^{\circ}C$ in a hot press. In MOR The OSB of thin strand thickness $0.3{\pm}0.05mm$(length 45mm) and density 0.85gr/$cm^3$ was the highest. The strand thickness had more effect on MOR than the strand length. In strand thickness $0.4{\pm}0.05mm$(length 60mm) and density 0.85gr/$cm^3$ was the highest MOE. The strand thickness and length had adverse effects on MOE each other. At internal bonding. The OSB of strand thickness $0.3{\pm}0.05mm$(length 45mm) and board density 0.75gr/$cm^3$ showed the highest value. OSB had higher IB value with thinner strand thickness. The thinner strand thickness showed the lower thickness swelling in turn $0.3{\pm}0.05mm$(length 45mm), $0.4{\pm}0.05mm$(length 60mm), $0.5{\pm}0.05mm$(length 75mm). $0.6{\pm}0.05mm$(length 90mm). Target densities 0.75gr/$cm^3$ 0.65gr/$cm^3$, 0.85gr/$cm^3$ showed in turn lower value. Finally, The OSB made of thinned wood of Larix leptolepis Gordon showed good results in laboratory experiment.

• 터널과지하공간
• /
• 제22권1호
• /
• pp.69-76
• /
• 2012

본 논문은 폭약의 폭발현상을 이용한 폭발용접, 폭발성형과 충격분말고화기술의 기본적 원리와 실험방법, 실험결과에 대하여 기술한다. 타이타늄(Ti)과 스테인레스 강(Stainless steel, SUS 304) 판재의 폭발용접 실험결과, 두 재료 접촉면의 단면에서는 연속적인 젯(jet)모양의 파형이 관찰되었고, 두 금속판재의 설치 경사각도가 $15{\sim}20^{\circ}$ 이고 접착속도가 2,100~2,800 m/s인 경우에 최적의 접합조건을 보였다. 알루미늄(Al) 판재를 이용한 폭발성형 실험과 전형적인 가압성형 실험 결과를 비교분석하여, 폭발성형의 경우가 큰 곡률변형을 보여 가공성이 우수한 것으로 확인되었다. 끝으로 금속과 세라믹의 혼합분말($Fe_{11.2}La_2O_3Co_{0.7}Si_{1.1}$)에 대한 충격고화 실험법을 제안하고 실험을 수행한 결과, 고화체의 표면과 내부에 균열이 확인되지 않았으며 세라믹입자와 금속입자들의 강한 미세조직 결합이 형성되었다. 또한 충격분말고화실험에서 발생되는 폭약의 폭발에 의한 폭굉파와 수중 충격파의 전파 및 간섭현상을 분석하기 위하여 LS-Dyna 3D를 이용한 동적해석을 수행하였다. 그 결과, 물용기 내 벽면에서 반사된 수중충격파가 중앙부에서 중첩되어 폭약의 폭발압력보다 높은 20 GPa의 수중 충격압을 보여, 물용기 내부형상의 중요성을 입증하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1998년도 제14회 학술발표회 논문개요집
• /
• pp.77-77
• /
• 1998

Present silicon dioxide (SiOz) 떠m as intennetal dielectridIMD) layers will result in high parasitic c capacitance and crosstalk interference in 비gh density devices. Low dielectric materials such as f f1uorina뼈 silicon oxide(SiOF) and f1uoropolymer IMD layers have been tried to s이ve this problem. I In the SiOF ftlm, as fluorine concentration increases the dielectric constant of t뼈 film decreases but i it becomes unstable and wa않r absorptivity increases. The dielectric constant above 3.0 is obtain어 i in these ftlms. Fluoropolymers such as polyte$\sigma$따luoroethylene(PTFE) are known as low dielectric c constant (>2.0) materials. However, their $\alpha$)Or thermal stability and low adhesive fa$\pi$e have h hindered 야1리ru뚱 as IMD ma따"ials. 1 The concept of a plasma processing a찌Jaratus with 비gh density plasma at low pressure has r received much attention for deposition because films made in these plasma reactors have many a advantages such as go여 film quality and gap filling profile. High ion flux with low ion energy in m the high density plasma make the low contamination and go어 $\sigma$'Oss피lked ftlm. Especially the h helicon plasma reactor have attractive features for ftlm deposition 야~au똥 of i앙 high density plasma p production compared with other conventional type plasma soun:es. I In this pa야Jr, we present the results on the low dielectric constant fluorocarbonated-SiOF film d밑JOsited on p-Si(loo) 5 inch silicon substrates with 00% of 0dFTES gas mixture and 20% of Ar g gas in a helicon plasma reactor. High density 띠asma is generated in the conventional helicon p plasma soun:e with Nagoya type ill antenna, 5-15 MHz and 1 kW RF power, 700 Gauss of m magnetic field, and 1.5 mTorr of pressure. The electron density and temperature of the 0dFTES d discharge are measUI벼 by Langmuir probe. The relative density of radicals are measured by optic허 e emission spe따'Oscopy(OES). Chemical bonding structure 3I피 atomic concentration 따'C characterized u using fourier transform infrared(FTIR) s야3띠"Oscopy and X -ray photonelectron spl:’따'Oscopy (XPS). D Dielectric constant is measured using a metal insulator semiconductor (MIS;AVO.4 $\mu$ m thick f fIlmlp-SD s$\sigma$ucture. A chemical stoichiome$\sigma$y of 야Ie fluorocarbina$textsc{k}$영-SiOF film 따~si야영 at room temperature, which t the flow rate of Oz and FTES gas is Isccm and 6sccm, res야~tvely, is form려 야Ie SiouFo.36Co.14. A d dielec$\sigma$ic constant of this fIlm is 2.8, but the s$\alpha$'!Cimen at annealed 5OOt: is obtain려 3.24, and the s stepcoverage in the 0.4 $\mu$ m and 0.5 $\mu$ m pattern 킹'C above 92% and 91% without void, res야~tively. res야~tively.

• Restorative Dentistry and Endodontics
• /
• 제22권1호
• /
• pp.61-75
• /
• 1997

The bond strengths of composite resin to tooth dentin vary with the methods of cavity preparation and surface treatment. Recent developments in techniques of dentinal surface treatment have renewed interest in microabrasive as a means of tooth preparation, The purpose of this study was to determine the effects of a new method of cavity preparation on the bond of composite resin to dentin. Freshly extracted 144 healthy human third molars were used in this study. The dentin surfaces prepared with #600 SiC abrasive paper were divided into control and air abrasion groups according to the method of dentin surface preparation using different combinations of delivery pressure, time, and acid etching. The shear bond strengths were measured after the composite resin (Clearfil Photo Bright) was bonded to prepared dentin surfaces by light-curing using a dentin bonding system (All-bond 2), In addition, the average surface roughness was measured to investigate the effect of differently prepared dentin surfaces on the shear bond strengths. The surface changes of prepared dentin and the debonded dentin surfaces were observed with SEM (S-2300, Hitachi Co., Japan). The following results from this-study were obtained ; 1. There was no significant difference of shear bond strengths according to the changes of delivery pressure and time. 2. The shear bond strengths were lower than the control in the air abraded-only groups, but those of the additional acid-etched groups were higher than the control. 3. The shear bond strengths to all air-abraded surfaces were increased by acid etching. 4. The correlation between shear bond strengths and surface roughness was not certain, although the mean surface roughness of all air-abraded surfaces has increased evidently while it has slightly decreased for additional acid etching. 5. On SEM examination, the dentinal tubules were almost occluded in the air abraded-only groups, but those were opened in the additional acid-etched groups. 6. The debonded surfaces were showed adhesive failure mode in the air abraded- only groups, while those were showed mainly the mixed and cohesive failure mode in the additional acid-etched groups. These results suggest that the layer produced during cavity preparation or surface treatment with air abrasion must be removed for maximum bond strength of composite resin to dentin.

• 접착 및 계면
• /
• 제23권2호
• /
• pp.25-32
• /
• 2022

최근 환경 규제로 인해 용제형 대신 수계형 점착제의 수요가 커지고 있으며, 물성 저하의 문제점을 보완하기 위해 쓰이는 점착부여제에도 그만큼 기대하는 요구가 커지고 있다. 따라서 본 연구에서는 하드 및 기능성 아크릴 단량체인 CHMA, IBOA, AA의 조성에 따라 수계 아크릴 점착 부여제를 합성하고, 이를 10 phr의 함량으로 점착제에 투입하여 점착부여제의 조성에 따른 물리적 특성을 비교하였다. 초기 점착력은 CHMA가 증가하고 IBOA가 감소함에 따라 감소하였고, AA 함량 증가로 인해 분자간의 결합력이 증가하였기 때문에 AA 함량이 낮을수록 더 좋은 결과를 나타내었다. 점착력은 점착부여제를 첨가함에 따라 고분자 사슬의 유동성을 높여 증가하는 결과를 나타내었으며, AA 함량이 높을수록 수소 결합이 더 많이 이루어짐으로써 더 좋은 결과를 나타내었다. 내열 유지력은 CHMA가 증가할수록 상대적으로 내열 유지력에 큰 영향을 미치는 IBOA의 함량이 감소하였기 때문에 전체적으로 감소하는 결과를 나타내었고, AA 함량이 높은 시리즈가 더 좋은 결과를 나타내었다.

• Design & Manufacturing
• /
• 제17권1호
• /
• pp.20-26
• /
• 2023

Lab-on-a-disc is a circular disc shape of cartridge that can be used for blood-based liquid biopsy to diagnose an early stage of cancer. Currently, liquid biopsies are regarded as a time-consuming process, and require sophisticated skills to precisely separate cell-free DNA (cfDNA) and circulating tumor cells (CTCs) floating in the bloodstream for accurate diagnosis. However, by applying the lab-on-a-disc to liquid biopsy, the entire process can be operated automatically. To do so, the lab-on-a-disc should be designed to prevent blood leakage during the centrifugation, transport, and dilution of blood inside the lab-on-a-disc in the process of liquid biopsy. In this study, the main components of lab-on-a-disc for liquid biopsy are fabricated by injection molding for mass production, and ultrasonic welding is employed to ensure the bonding strength between the components. To guarantee accurate ultrasonic welding, the flatness of the components is optimized numerically by using the response surface methodology with four main injection molding processing parameters, including the mold & resin temperatures, the injection speed, and the packing pressure. The 27 times finite element analyses using Moldflow® reveal that the injection time and the packing pressure are the critical factors affecting the flatness of the components with an optimal set of values for all four processing parameters. To further improve the flatness of the lab-on-a-disc components for stable mass production, a quarter-disc shape of lab-on-a-disc with a radius of 75 mm is used instead of a full circular shape of the disc, and this significantly decreases the standard deviation of flatness to 30% due to the reduced overall length of the injection molded components by one-half. Moreover, it is also beneficial to use a quarter disc shape to manage the deviation of flatness under 3 sigma limits.

• 한국가스학회지
• /
• 제11권1호
• /
• pp.23-28
• /
• 2007

본 본문에서는 LPG 용기용 가스밸브의 O-링과 밸브패킹의 밀봉결함과 크랙에 관련된 실험적 연구를 수행하고자 한다. LP 가스의 누출을 방지하기 위해 사용하는 O-링은 LPG 밸브의 밀봉 안전성을 확보하는 핵심부품으로 대단히 중요하다. 밸브패킹은 LPG 연료의 공급과 충전을 하는데, 가스 공급구를 열고 닫는 중요한 역할을 담당한다. 이들 두개의 밀봉부품에 대한 성능은 밸브의 누설 안전성과 장수명에 밀접한 관련이 있다. 연구결과에 의하면, O-링의 대부분은 파티션 부근의 결합불량과 과도한 압축률로 인해 원주방향으로 크랙이 발생하는 것으로 분석되었다. 그 이외의 결함으로 거론된 경우는 LP가스의 과도한 가스압력으로 인한 압출현상의 발생은 압출크랙을 일으키는 원인으로 작용하고 있다. 따라서 본 논문에서는 가스밸브의 누설 안전성을 확보하고 수명을 연장하기 위해 O-링과 밸브패킹에 대한 엄격한 품질관리와 인증제도의 도입을 권장하고자 한다. 결국에는 LPG용기용 밸브의 품질과 안전성 확보를 위해 밀봉장치에 대한 품질안전 보증제도를 도입해야 밸브를 오랫동안 사용할 수 있을 것이다.