• Restorative Dentistry and Endodontics
• /
• 제12권2호
• /
• pp.45-53
• /
• 1987

The purpose of this study was to evaluate the tensile bond strength between composite resin and the human enamel. Three composite resin systems, two chemical (Clearfil Posterior, and Clearfil Posterior-3) and one light cure (Photo Clearfil-A), used with and without an intermediate resin (clearfil bonding agent), were evaluated under different amounts of load (10g, 200g and 200g for a moment) for in vitro tensile bond strength to acid-eched human enamel. Clinically intact buccal or lingual surfaces of 144 freshly extracted human permanent molars, embedded in acrylic were flattened with No #600 carborundum discs. Samples were randomly assigned to the different materials and treatments using a table of random numbers. Eight samples were thus prepared for each group(Table 2) these surfaces were etched with an acid etchant (Kurarey Co. Japan) in a mode of etching for 30 seconds, washing for 15 seconds, and drying for 30-seconds. During the polymerization of composite resin on the acid-etched enamel surfaces with and without bonding agent 10-gram, 200 gram and temporary 200 gram of load were applied. The specimens were stored in 50% relation humidity at $37^{\circ}C$ for 24 hours before testing. An universal Testing machine (Intesco model No. 2010, Tokyo, Japan) was used to apply tensile loads in the vertical directed (fig 5), and the force required for separation was recorded with a cross head speed of 0.25 mm/min and 20 kg in full scale. The results were as follow: 1. The tensile bond strength was much greater in applying a bonding agent than in not doing that. 2. The tensile bond strength of chemical cure composite resin was higher than that of light cure composite resin with applying on bonding agent on the acid-etched enamel. 3. In case of not applying a bonding agents on the acid-etching enamel, the highest tensile bond strength under 200 gram of load was measured in light cure composite resin. 4. The tensile bond strength under 200-gram of load has no relation with applying the bonding agent. 5. Under the load of 10-gram, There was significant difference in tensile bond strength as applying the bonding agent.

• Bulletin of the Korean Chemical Society
• /
• 제33권8호
• /
• pp.2719-2723
• /
• 2012

A kinetic study is reported for nucleophilic substitution reactions of benzyl 4-pyridyl carbonate 6 with a series of alicyclic secondary amines in MeCN. The plot of pseudo-first-order rate constant ($k_{obsd}$) vs. [amine] curves upward, which is typical for reactions reported previously to proceed through a stepwise mechanism with two intermediates (i.e., a zwitterionic tetrahedral intermediate $T^{\pm}$ and its deprotonated form $T^-$). Dissection of $k_{obsd}$ into the second- and third-order rate constants (i.e., $Kk_2$ and $Kk_3$, respectively) reveals that $Kk_3$ is significantly larger than $Kk_2$, indicating that the reactions proceed mainly through the deprotonation pathway (i.e., the $k_3$ process) in a high [amine] region. This contrasts to the recent report that the corresponding aminolysis of benzyl 2-pyridyl carbonate 5 proceeds through a forced concerted mechanism. An intramolecular H-bonding interaction was suggested to force the reactions of 5 to proceed through a concerted mechanism, since it could accelerate the rate of leaving-group expulsion (i.e., an increase in $k_2$). However, such H-bonding interaction, which could increase $k_2$, is structurally impossible for the reactions of 6. Thus, presence or absence of an intramolecular H-bonding interaction has been suggested to be responsible for the contrasting reaction mechanisms (i.e., a forced concerted mechanism for the reaction of 5 vs. a stepwise mechanism with $T^{\pm}$ and $T^-$ as intermediates for that of 6).

• The Journal of Advanced Prosthodontics
• /
• 제11권6호
• /
• pp.313-323
• /
• 2019

PURPOSE. Shear bond strength (SBS) test is the most commonly used method for evaluating resin bond strength of zirconia, but SBS results vary among different studies even when evaluating the same bonding strategy. The purpose of this study was to promote standardization of the SBS test in evaluating zirconia ceramic bonding and to investigate factors that may affect the SBS value of a zirconia/resin cement/composite resin bonding specimen. MATERIALS AND METHODS. The zirconia/resin cement/composite resin bonding specimens were used to simulate loading with a shear force by the three-dimensional finite element (3D FE) modeling, in which stress distribution under uniform/non-uniform load, and different resin cement thickness and different elastic modulus of resin composite were analyzed. In vitro SBS test was also performed to validate the results of 3D FE analysis. RESULTS. The loading flat width was an important affecting factor. 3D FE analysis also showed that differences in resin cement layer thickness and resin composite would lead to the variations of stress accumulation area. The SBS test result showed that the load for preparing a SBS specimen is negatively correlated with the resin cement thickness and positively correlated with SBS values. CONCLUSION. When preparing a SBS specimen for evaluating bond performance, the load flat width, the load applied during cementation, and the different composite resins used affect the SBS results and therefore should be standardized.

• 방사선산업학회지
• /
• 제6권1호
• /
• pp.89-94
• /
• 2012

Three-dimensional network hydrogels were prepared by ${\gamma}$-irradiation of aqueous solutions of poly(vinyl alcohol) (PVA) and glycerol (Gly). Oven-drying was used to measure the gel fraction (G), hydration (H) or swelling behavior (S) of the prepared hydrogels. This study made a hypothesis that hydrogen bonds due to addition of glycerol and change of dry states such as freeze-drying (FD), room-drying (RD) and oven-drying (OD) acts on the G, H, and S. Interesting results on the hydrogen bonding effect in the prepared hydrogels are monitored at different drying conditions. The FD samples have a higher G values with increase in glycerol content as compared with the OD and RD samples. The formation of strong hydrogen bonding network among Gly molecules and hydrogel matrix was considered as the main driving force, resulting in the changes in the G, H, and S of the hydrogels under different drying conditions.

• Composites Research
• /
• 제31권6호
• /
• pp.299-303
• /
• 2018

탄소섬유 강화 PA6 복합재료의 탄소섬유-메트릭스간 계면결합력과 반응중합도 향상을 위해서 기존 탄소섬유의 에폭시 사이징제를 디사이징처리하여 에폭시를 제거한 후 우레탄계, 나일론계, 페녹시계 사이징제로 재처리해주었으며, 리사이징처리된탄소섬유의표면을관찰하였다. 리사이징처리된탄소섬유의계면결합력은 IFSS(Interfacial shear strength)를 통해서 확인하였으며, 계면 결합 강도 측정 후 파단면은 주사전자현미경을 통해서 관찰하였다. 나일론계와 페녹시계 사이징제로 처리된 탄소섬유가 우레탄계 사이징에 비해 계면 결합력이 상승한 것을 확인하였다. 우레탄계 리사이징 처리된 탄소섬유는 기존 에폭시 사이징 탄소섬유보다 계면 결합력이 감소한 것으로 확인되었다. 이 결과는 기존 탄소섬유의 저활성과 평활성을 제거하여 탄소섬유와 나일론6 사이의 계면 결합력이 향상된 것으로 판단된다.

• Bulletin of the Korean Chemical Society
• /
• 제24권8호
• /
• pp.1097-1101
• /
• 2003

The cubic and quartic anharmonic force field of malonaldehyde is calculated using density functional theory at the B3LYP/6-31G(d,p) level, and used to simulate coherent infrared vibrational spectra. 12 normal modes are included in the simulation, and the Arnoldi method is employed for the diagonalization of the Hamiltonian. The calculated three pulse infrared signals in the k1 + k2 - k3 direction show signatures of the intramolecular hydrogen bond couplings between the C=O stretch, H-O-C bend and O-H stretch vibrations.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.943-946
• /
• 2000

Selective laser sintering(SLS) is a solid freeform fabrication process whereby a part is built layerwise by scanning a powder bed. The properties of metal powder are dependent on the heat, it is not easy to do the exact error compensation with analysis and estimation by modeling. This paper suggests that the error is compensated by experimental method and then the accuracy of shape is enhanced by revising of STL file. Also bonding force is measured by an experiment with change of process path.

• Bulletin of the Korean Chemical Society
• /
• 제11권4호
• /
• pp.313-317
• /
• 1990

Geometries for several representative quinolone carboxylate type antibacterials have been calculated by computer graphics/molecular mechanics energy minimization procedures using both MM2 and AMBER force fields. The calculated geometries were found to be in reasonable agreements with the corresponding X-ray crystal structures. It has been pointed out that notwithstanding the weaknesses associated with calculating the resonance and hydrogen bonding contributions, the employed methods are capable of generating credible ring geometries and torsional angle dispositions of N(1)-ethyl and 3-carboxylate substituents of the quinolones.

• 콘크리트학회지
• /
• 제9권5호
• /
• pp.207-216
• /
• 1997

암석학적 특징이 다른 골재를 사용할 때 콘크리트의 기본특성에 영향을 골재품질 시험과 함께, 화학분석, X.R.D, D.T-T.G.A S.E.M, 편광현미경, 실체현미경관찰등을 하여 조사하므로서 암질특성과 콘크리트의 기본특성과의 관계를 해석하였다. 연구결과, 운모 또는 점토계 광물과 같은 풍화광물이 혼재하지 않고 거대 결정을 갖ㄴ 화강암계 골재는 풍화 화강암, 안산암, 석회암, 골재에 비해 골재품질이 저조해도 작업성이나 강도특성이 우수하였다. 이는 골재의 표면거칠기와 구형도가 양호해 골재와 시멘트페이스트의 부착력이 강화되기 때문이며 고강도콘크리트제조를 위한 골재의 암질로는 거대 결정으로 구성되고 풍화광물이 없는 암질을 선정하는 것이 중요하다. 결정이 크고 풍화광물(운모, 점토계 고아물)이 혼재되지 않은 화강암 골재를 사용한 고강도콘크리트는 석회암, 안산암 골재를 사용한 콘크리트에 비해 150-200kg/$\textrm{cm}^2$이상의 강도증진과 작업성이 향상되었다.

• 한국염색가공학회지
• /
• 제1권1호
• /
• pp.26-34
• /
• 1989

The selective chemical degradation or etching of PET based on an organic amine attack on the ester group. The techniques involves the chemical removal of loss ordered amorphous regions or crystalline regions, which are essentially unaffected by the degradative etchant. Thus, most of previous studies have limited to consideration which has been given to structural changes taking place. Therefore, this study was carried out to investigate surface characterization, dyeing properties of PET film hydrazinolyzed with hydrazine hydrate in methanol. PET film was treated with 30% hydrazine hydrate in methanol at $30^\circ{C}$ for various time intervals. The total surface tension of treated PET increased, the dispersion force decreased and the hydrogen bonding force increased. The equilibrium dye adsorption, dyeing rate and apparent diffusion coefficient of acid dyes increased, and the apparent activation energies of diffusion decreased.