• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.299-305
• /
• 2019

As the damage factors of the three­storey stone pagoda of the Bulguksa Temple in Gyeongju could cause a reduction in the historical and artistic value and accelerate the deterioration of the stone, an appropriate solution is needed. The aim of stone conservation is to conserve the original shape and convey originality from the ancestors to their descendants. This procedure includes a record of the condition, being available in the future. In particular, the damage assessment could be used in conservational research, educational data, conservational treatment, and preventive data. As a result of quantitative damage assessment, biological damage indicated 159 %, chemical damage 114 %, and physical damage 16 %. The west direction revealed 95 % because of the amount of sunshine, moisture, and expansion of rock. Complex factors and high range damage were observed on the foundation and body of the pagoda. Since the top of pagoda was restored in the 1970s, the state presented a good condition. By doing this, the number of organisms could be reduced by cleaning and the physical damage could be minimized by bonding. On the other hand, continuous monitoring will be needed because there is a possibility of reforming the damage in the future.

• Applied Chemistry for Engineering
• /
• v.34 no.5
• /
• pp.534-540
• /
• 2023

The high-rate performance is limited by several factors, such as polarization generation, low electrical conductivity, low surface energy, and low electrolyte permeability of CF_X, which is widely used as a cathode active material in the lithium primary battery. Therefore, in this study, we aimed to improve the battery performance by using carbon fluoride modified by surface treatment using oxygen plasma as a cathode for lithium primary batteries. Through XPS and XRD analysis, changes in the surface chemical characteristics and crystal structure of CF_X modified by oxygen plasma treatment were analyzed, and accordingly, the electrochemical characteristics of lithium-ion primary batteries were analyzed and discussed. As a result, the highest number of semi-ionic C-F bonds were formed under the oxygen plasma treatment condition (7.5 minutes) with the lowest fluorine to carbon (F/C) ratio. In addition, the primary cell prepared under this condition using carbon fluoride as the active material of the cathode showed the highest 3 F/C(3 C rate-performance) rate-performance and maintained a relatively high capacity (550 mAh/g) even at high rates. In this study, it was possible to produce lithium primary batteries with high-rate performance by adjusting the fluorine contents of carbon fluoride and the type of carbon-fluorine bonding through oxygen plasma treatment.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.1
• /
• pp.139-146
• /
• 2015

The amount of by-product from sulphur increases in domestic industrial facilities. However, the amount of its consumption is limited so that the amount of unused sulphur continues to increase. Therefore, in this study, the use sulfur polymer as the concrete surface protecting material was conducted. The compressive strength showed that as the substitution ratio of filler increased up to 40%, the compressive strength also increased. A high compressive strength was shown at the curing temperature of $40^{\circ}C$ (SS, FA) and $60^{\circ}C$ (OPC) according to the type of filler. The difference of compressive strength between air dry curing and water curing was insignificant so that there was no significant influence of moisture during curing process. The evaluation result of bond strength showed that the highest bond strength was shown at the air-dry condition of $40^{\circ}C$ regardless of type of filler. Bonding didn't occur properly during water curing in comparison to air dry curing. Also, in case of the specimen cured at $60^{\circ}C$, discoloration and hair cracks appeared due to the influence of temperature, and the highest bond strength was shown at the substitution ratio of 20% (SS, FA) and 30% (OPC) according to the type of filler. The releasing test result of harmful substance showed that no harmful substance was released, so there is no harmfulness in the surface protecting material using sulfur polymer. As a conclusion drawn in this study, it is most appropriate to substitute silica by approximately 20%, mix and cure at the air-dry condition of $40^{\circ}C$ in order to use sulfur polymer as the surface protecting material.

• Journal of the Korean Society of Child Welfare
• /
• no.56
• /
• pp.133-164
• /
• 2016

This study investigated the effect of housing poverty in childhood on adolescents' subjective well-being. Specifically, this study examined whether the major factors that have been known to affect adolescents' well-being (i.e., family relationships, peer relationships, school adjustment etc.) mediated the relationship between housing poverty and adolescents' well-being. And then this study aimed to present an empirical evidence for establishing policies against housing poverty in order to enhance adolescent's subjective happiness. Data were derived from the $1^{st}$, $4^{th}$, and $7^{th}$ surveys of the Korea Welfare Panel Study(KOWEPS), and the sample included. 512 high school children in the $7^{th}$ survey. This study utilized structural equation modeling. Housing poverty was measured by the sub-minimum standard housing condition and the household's burden of housing expenditure. Family relationship, as a mediator, was measured by parental involvement in education, parental monitoring, and family conflicts. Another mediator, school adjustment was measured by school environment and school bonding, and the last mediator, peer relationship was measured by friend attachment and peer attachment. The results showed that housing poverty had significant negative effects on the adolescents' subjective well-being. The sub-minimum standard housing condition with inadequate size and facilities negatively affected adolescents' relationships with family directly and subjective well-being indirectly. In addition, the negative family relationships due to the sub-minimum standard housing condition negatively affected adolescents' subjective well-being through school adjustment and peer relationships. The greater the proportion of income a household spends on housing expenditure, the less likely for adolescents to report positive well-being. The sub-minimum standard housing condition had indirect effects through family relationships, whereas the household's housing expenditure directly affected adolescents' subjective well-being. This study suggested the necessity of interventions to alleviate housing poverty for adolescents' families and lays the groundwork for housing poverty policies in Korea.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.559-571
• /
• 2017

This study was conducted to determine the adhesive performances of plywoods affected by layering direction and the amounts of thermoplastic films. The face and back layers of veneer were hardwood species (Mixed light hardwood) and core layer veneer was radiata pine (Pinus radiata D. Don). Thermoplastic film used as adhesive were polypropylene (PP) film and polyethylene (PE) film. Thermal analysis and tensile strength were investigated on each films. As a result, the melting temperature of PP and PE films were $163.4^{\circ}C$ and $109.7^{\circ}C$, respectively, and the crystallization temperature were $98.9^{\circ}C$ and $93.6^{\circ}C$, respectively. Tensile strength and elongation of each films appeared higher on the width direction than length direction. Considering the characteristics of the thermoplastic films, the test for the amount of film used was carried out by layering film to the target thickness on veneer. The effecting of layering direction of film on plywood manufacturing was conducted by laminating in the length and width directions of the film according to the grain direction of veneer. Tensile-shear strength of plywood in wet condition was satisfied with the quality standard (0.7 MPa) of KS F 3101 when the film was used over 0.05 mm of PP film and over 0.10 mm of PE film. Tensile-shear strength of plywood after cyclic boiling exceeded the KS standard when PP film was used 0.20 mm thickness. Furthermore, higher bonding strength was observed on a plywood made with width direction of film according to grain direction of veneer than that of length direction of film. Based on microscopic analysis of the surface and bonding line of plywood, interlocking between veneers by penetration of a thermoplastic film into inner and cracks were observed.

• The korean journal of orthodontics
• /
• v.34 no.5 s.106
• /
• pp.439-447
• /
• 2004

The purpose of this study was to investigate the influence of water, saliva and blood contamination on the bonding strength of metal brackets with a self-etching primer/adhesive to enamel. Ninety-six extracted human teeth were divided into four groups. The brackets were bonded to enamel with a self- etching primer (3M/Unitek Dental Products. Monorovia California) according to one of four protocols. The teeth were bonded in a dry condition (group D) or in contamination with distilled water (group W), artificial saliva (group S). or fresh human blood (group B) Shear bond strengths were tested using an Instron Universal testing machine. After debonding. bracket and tooth surfaces were examined with a stereomicroscope. In each group, four samples were selected and examined with a Scanning electron microscope of the prepared enamel surface and resin-enamel interlace. The results obtained were summarized as follows: Shear bond Strength if group D $(15.22{\pm}2.86MPa)$ and W $(15.20{\pm}3.85 MPa)$ Were higher than in group B$(12.56{\pm}2.94MPa)$ (p<0.05). There were no statistical differences in the shear bond strengths between groups D. W and S (p>0.05). There was a tendency to have less residual adhesive remaining on the enamel surfaces of group B than group D. The SEW morphology of group D and W showed a more roughened etching pattern than group S and B. Water or saliva contamination on bending of orthodontic brackets with Transbond plus self etching primer had almost no influence on bond strength In this study, the blood contaminated group showed the lowest bond strength, but it was above the clinically acceptable bond strength (5.9-7.8 MPa, Reynold, 1975). The results of this study suggest that acceptable clinical bond strengths can be obtained in wet conditions when self-etching adhesives are used.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.17 no.2
• /
• pp.93-103
• /
• 1981

It is well-known that nowadays heat resisting and anti-corrosive materials have been widely used as the components materials of gas turbines, nuclear power plants and engines etc. In the fields of machine production industry. And materials for engine components, like as the exhaust valve of internal combustion engine, have been required to operate under the high temperature range of $700^{\circ}C$-$800^{\circ}C$ and high pressured gas with repeated mechanical load for the high performance of engines. For these components, friction welding for bonding of dissimilar steels can be applied for in order to obtain process shortening, production cost reduction and excellent bonding quality. And age hardening recently has been noticed to the heat resisting materials for further strengthening of high temperature strength, especially high temperature fatigue strength. However, it is difficult to find out any report concerning the effects of age hardening for strengthening high temperature fatigue strength to the Friction welded heat resisting and anti-corrosive materials. In this study the experiment was carried out as the high temperature rotary bending fatigue testing under the condition of $700^{\circ}C$ high temperature to the friction welded domestic heat resisting steels, SUH3-SUS303, which were 10hr., 100hr. aging heat treated at $700^{\circ}C$ after solution treatment 1hr. at $1, 060^{\circ}C$ for the purpose of observing the effects of the high temperature fatigue strength and fatigue fracture behaviors as well as with various mechanical properties of welded joints. The results obtained are summarized as follows: 1) Through mechanical tests and micro-structural examinations, the determined optimum welding conditions, rotating speed 2420 rpm, heating pressure 8kg/mm super(2), upsetting pressure 22kg/mm super(2), the amount of total upset 7mm (heating time 3 sec and upsetting time 2 sec) were satisfied. 2) The solution treated material SUH 3, SUS 303, have the highest inclination gradient on S-N curve due to the high temperature fatigue testing for long time at $700^{\circ}C$. 3) The optimum aging time of friction welded SUH3-SUS 303, has been recognized near the 10hr. at $700^{\circ}C$ after the solution treatment of 1hr. at $1, 060^{\circ}C$. 4) The high temperature fatigue limits of aging treated materials were compared with those of raw material according to the extender of aging time, on 10hr. aging, fatigue limits were increased by SUH 3 75.4%, SUS 303 28.5%, friction welded joints SUH 3-SUS 303 44.2% and 100hr. aging the rates were 64.9%, 30.4% and 36.6% respectively. 5) The fatigue fractures occurred at the side of the base matal SUS303 of the friction welded joints SUH 3-SUS 303 and it is difficult to find out fractures at the friction welding interfaces. 6) The cracking mode of SUS 303, SUH 3-303 is intergranular in any case, but SUH 3 is fractured by transgranular cracking.

• Korean Journal of Soil Science and Fertilizer
• /
• v.10 no.1
• /
• pp.1-6
• /
• 1977

Fifteen soils including volcanic ash, acid sulfate and degraded saline soils were investigated for Languir adsorption isotherm of ammonium using $NH_4H_2PO_4$. The results are as follows. Languir adsorption maxima of ammonium (LAMA) ranged from 2.4me/100g soil to 12.3 and the average was 5.3. Initial concentration of 30 to 60 or 40 to 80 ppm(as N) appears to be suitable for LAMA measurement. There were two LAMA in some soils. Difference between adsorption constants (bonding energy) was mostly greater than that between LAMA. LAMA ranged from 9.4% to 72% of cation exchange capacity and average was 47%. It did not show any clear tendency with CEC, pH, organic matter content, base saturation percent, P, K, Ca, Mg, Na and Si. Except volcanic ash soils which were grouped into two groups according to ammonium adsorption LAMA was significantly (r=0.951 at 1%) correlated with adsorption at 200ppm. This single concentration seems suitable for LAMA measurement. Probable mechanism of ammonium adsorption was discussed, in which the associated anions were combined with iron and aluminum and then ammonium was bound to phosphorus. Applicability of Langmuir adsorption isotherm model to the soils under field condition was also discussed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.17 no.2
• /
• pp.82-89
• /
• 2007

Glass-ceramics were fabricated by heat-treating a glass at $700^{\circ}C$/10hr which was obtained by melting a glass frit mixed with $40{\sim}80 wt%$ EAF dust at $1300^{\circ}C$/1hr. Dependence of crystal phase and bonding state change upon a compositional change and heat treatment condition were studied and the results was connected to the toxic characterization leaching procedure (TCLP) test data to investigate a chemical durability of the specimens. Increasing dust in a glass shifted the peak around $1000cm^{-1}$ to the lower frequency which was composed of two vibration peaks for the nonbridging oxygen at $960cm^{-1}$ and the bridging oxygen at $1050{\sim}1060cm^{-1}$. Also, the $B_2O_3$ structure of boroxol ring changed to a tetrhedral-, trigonal- and di-borate with dust addition. The Fe-O peaks in the glass-ceramics were observed which is consitent with XRD results of spinel formation. The surface of glass after TCLP test was severely cracked while there was no cracks on a glass-ceramics after TCLP test so the chemical durability of the glass-ceramics is superior than that of glass. The leaching concentration of Fe for the glass-ceramics containing EAF dust 80 wt% is 1/15 times lower than that of glass. The Zn leaching concentration fur the glass-ceramics containing dust < 70 wt% was higher than that of glass but its trend was reversed for the specimen of dust content > 80 wt% which could be concluded as correlated with occurrence of willemite phase.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.28 no.1
• /
• pp.19-28
• /
• 2008

Effect of Water Treatment Sludge(WTS) on trace metals content in Sorghum(Sorghum bicolor(L.) Moench) was investigated. At this report measuring of nickel(Ni) content of the forage was presented. Four treatments, Control, Compost, Alum+(nitrogen, phosphorus, potassium)(NPK), Compost+NPK, were applied to the sorghum in a mountainous place near the Joongbu University. With the 1, 3, 5 hours conditions, the background value was the least on the 5 hours warming up of the AA-680 spectrophotometer, and on the condition(mean/SD) of absorbances of Ni observed was the most. It is necessary in Ni analysis warming up for longer period around 5 hours for this type of apparatus. And we think that the difference of warming time for Ni analysis in order to carry out better measuring; the reason might be the larger bonding energy of Ni than those of Cu, calcium(Ca), magnesium(Mg) and (potassium)(K).