• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.2
• /
• pp.8-8
• /
• 1987

This paper describes on the distribution of the vibration and the noise produced on a skipjack pole and line training ship M/S Pusan 403 (243GT, 1,000ps) under the cruising or drifting condition. The vibration and the noise level were measured by use of protable vibration analyzer (B and K 3513) and sound level meter (B and K 2205), and so the vibration level was converted into dB unit. The check points were set through every decks and around important places of the ship. The results obtained can be summarized as follows: 1. The vibration and the noise level 1) On the main deck, both the vibration and the noise level were highest at the vertically above the main engine, whereas the vibration level was the lowest in the bow store and the noise level beneath the bridge. 2) Under cruising condition, the vibration level around the cylinder head of main engine, port side of the engine room, on the shaft tunnel was 80, 67, 65 dB and the noise level 104, 87, 86 dB, respectively. 3) The vibration level on the vertical line passing through the bridge was the highest at the orlop deck with 60 dB and the lowest on the bridge deck with 55 dB, whereas the noise level the highest at the compass deck with 75 dB and the lowest at the orlop deck with 53 dB. 4) The vibration and the noise level on the open decks were the highest with 65 dB and 84 dB on the boat deck, whereas the vibration level was the lowest at the lecture room with 51 dB and the noise level the lowest at the fore castle deck with 57 dB. 5) On the orlop decks, both the vibration and the noise level were the highest at the engine room with 65 dB and 85 dB, and the lowest at bow store with 54 dB and 52 dB, respectively. Comparing with the vibration level and the noise level, the vibration level was higher than the noise level in the bow part and it was contrary in the stern part of the ship. 2. Vibration analysis 1) The vibration displacement and the vibration velocity were the greatest at the cylinder head of main engine with 100μm and 11mm/sec, and were the smallest at the compass deck with 3μm and 0.07mm/sec. They were also attenuated rapidly around the frequency of 100Hz and over. 2) The vibration acceleration was the greatest at the cylinder head with the main frequency of 1KHz and the acceleration of 1.1mm/sec super(2), and the smallest at the compass deck with 30KHz and 0.05mm/sec super(2).

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.2
• /
• pp.54-60
• /
• 1987

This paper describes on the distribution of the vibration and the noise produced on a skipjack pole and line training ship M/S Pusan 403 (243GT, 1,000ps) under the cruising or drifting condition. The vibration and the noise level were measured by use of protable vibration analyzer (B and K 3513) and sound level meter (B and K 2205), and so the vibration level was converted into dB unit. The check points were set through every decks and around important places of the ship. The results obtained can be summarized as follows: 1. The vibration and the noise level 1) On the main deck, both the vibration and the noise level were highest at the vertically above the main engine, whereas the vibration level was the lowest in the bow store and the noise level beneath the bridge. 2) Under cruising condition, the vibration level around the cylinder head of main engine, port side of the engine room, on the shaft tunnel was 80, 67, 65 dB and the noise level 104, 87, 86 dB, respectively. 3) The vibration level on the vertical line passing through the bridge was the highest at the orlop deck with 60 dB and the lowest on the bridge deck with 55 dB, whereas the noise level the highest at the compass deck with 75 dB and the lowest at the orlop deck with 53 dB. 4) The vibration and the noise level on the open decks were the highest with 65 dB and 84 dB on the boat deck, whereas the vibration level was the lowest at the lecture room with 51 dB and the noise level the lowest at the fore castle deck with 57 dB. 5) On the orlop decks, both the vibration and the noise level were the highest at the engine room with 65 dB and 85 dB, and the lowest at bow store with 54 dB and 52 dB, respectively. Comparing with the vibration level and the noise level, the vibration level was higher than the noise level in the bow part and it was contrary in the stern part of the ship. 2. Vibration analysis 1) The vibration displacement and the vibration velocity were the greatest at the cylinder head of main engine with 100$\mu$m and 11mm/sec, and were the smallest at the compass deck with 3$\mu$m and 0.07mm/sec. They were also attenuated rapidly around the frequency of 100Hz and over. 2) The vibration acceleration was the greatest at the cylinder head with the main frequency of 1KHz and the acceleration of 1.1mm/sec super(2), and the smallest at the compass deck with 30KHz and 0.05mm/sec super(2).

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.3
• /
• pp.175-185
• /
• 2000

This paper described on a basic study to organize fishing vessel control system in order to control efficiently fishing vessel in Korean offshore. It was digitalized ARPA image on the fishing processing of a fleet of purse seiner in conducting fishing operation at Cheju offshore in Korea as a digital camera and then simulated by used VTMS. Futhermore, it was investigated on the application of FVTMS which can control efficiently fishing vessels in fishing ground. The results obtained were as follows ; (1) It was taken 16 minutes and 35 minutes to casting and hauling net in fishing processing respectively. The length of rope pulled by scout boat was 200m, tactical diameter in casting net was 340.8m, turning speed was 6kts as well. (2) The processing of casting and hauling net was moved to SW, NE as results of simulation when the current direction and speed set into NE, 2kts and SW, 2kts respectively. Such as these results suggest that can predict to control the fishing vessel previously with information of fishing ground, fishery and ship's maneuvering, etc. (3) The control range of VTMS radar used in simulation was about 16 miles. Although converting from a radar of the control vessel to another one, it was continuously acquired for the vector and the target data. The optimum control position could be determined by measuring and analyzing to distance and direction between the control vessel and the fleet of fishing vessel. (4) The FVTMS(fishing vessel traffic management services) model was suggested that fishing vessels received fishing conditions and safety navigation information can operate safely and efficiently.

• Journal of Preventive Medicine and Public Health
• /
• v.22 no.2 s.26
• /
• pp.290-301
• /
• 1989

This is preliminary report on anthrax epidemic occurred in an island with about 100 residents. Since 1982 there had been sudden deaths among all kinds of domestic animals including cattle, dogs, ducks, chicken and goat but only a few among cats in an isolated island about three hours distance away by ferry boat from Mokpo city. From 1986 through 1988 nine human deaths and four patients occurred, which made the government intervene for investigation on June 25 1988. The epidemiological investigation consisted of interview survey and medical examination, medical record analysis, laboratory work to isolate the pathogens under the direction of hypothesis derived from the study and further confirmation of the pathogens by international institute. The summarized results are as followings: 1. According to the interview survey there were many deaths among domestic animals usually in cold and dry season such as January through March and September through November; 36 heads of cattle leaving one head, more than 40 hogs(all), hundreds of chicken leaving few alive, goats that had taken home from mountain and two or three cats out of around 40 had sudden deaths from 1982 till 1985, when the residents stopped to purchase and take them into the island anymore. Also there were eleven persons who had experienced the similar syndrome complex to those of admitted and expired patients and four of them revealed typical chest X-ray findings; from one of these four patients(Rho) B. anthracis is isolated. 2. Medical record on patients who had been admitted, showed common characteristics of the disease course. On admission they had either gastrointestinal or upper respiratory infection symptoms which invariably progressed to septicemic nature with pulmonary interstitial infiltration and mediastinal widening/bulging, and then to deadly acute respiratory distress syndrome. At the end stage chest X-ray revealed multiple bullous emphysema. One of another characteristics was oral ulceration with bleeding occurred in about 50% of the patients. Laboratory test results in common were leukocytosis with left shift and abnormal liver and kidney functions, particularly at the later stage of the illness. 3. Epidemiological characteristics was striking in that both mortality and incidence rates were high: the mortality rate was 8.7% average, male being three times higher than females but there was no distictive clustering by age group. The incidence rate for both sexes was 28.2% and there was no sex difference although a tendency of higher incidence among older ages was noticed. The highest mortality and incidence were observed in Won village where the first death of animal occurred and with the highest frequency among three villages of the island. 4. Among twelve bacilli species isolated from various specimens, two strains, one from patient and the other from soil where the recently died cow is hurried, were confirmed as B. anthracis by Pasteur Institute and CDC of USA(strain from soil). CDC reported that the strain did not produce capsule in bicarbonate media but reacted with the bacteriophage and one of five sera taken from the patients. Mode of transmission as well as incubation period of the agent has not been established yet, which needs further investigation in relation to the antigenic structure of the variant when it is confirmed.

• Korean Journal of Poultry Science
• /
• v.8 no.1
• /
• pp.1-5
• /
• 1981

In trying to predict the effect of genetics on the broiler in the year 2000, this is a relatively short period of time as far as broiler genetics in concerned. Modern broiler genetics started around 1945 and tremendous gains when made in past 35 years. Futher improvements on broiler will depend on the evolution and revolution: 1. Evolution: (1) Growth rate has been made 4-5% per year. (2) Feed conversion has improved approximately 1% per year. (3) Abdominal fat is becoming a major complaint in broiler. (4) Because of the changing life-style, broiler meat sales in the future will be more and more in cut-up form. (5) Breeding for stress resistance and selection for docile temperament can be important in order to funker improve fled efficiency. (6) In female parent stock, reproduction characteristics are in many can negatively correlated with the desired broiler traits. (7) Egg production and hatchability in moot commercial parent nod m at a fairly high level. (8) In male parent stock, the heavier and mon super-meat-type male lines are desired to Product better broilers. 2. Revolution: Trying to forecast revolutionary change in broiler genetics is highly speculative, as sudden change are aften unpredictable. (1) Species hybridization, such as a turkey-chicken cross (2) Biochemical tools, such as blood typing. (3) Mutation breeding by radiation or chemical mutagentia. (4) Broiler breeding would be to change the phenotypic appearance by single gene, such as naked, wingless. (5) Changes in production techniques. such as growing in cage or growing in filtered air positive pressure houses.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.31 no.1
• /
• pp.59-70
• /
• 2013

This study was to suggest cultural landscape preservation, value creation, as well as utilization plan to help landscape development of Hahoe village by identify the existence of Okyeonsipyeong(玉淵十詠) natural features, which were set around Buyongdae(芙蓉臺) in Hahoe Village by Seoae(西崖) Ryu, Seongryong(柳成龍), and understanding their characteristics and meanings of natural features and meanings. Based on the writings of "Okyeonseodanggi" and "Okyeonsipyeong", the major results of this study are as belows. 'Okyeon(玉淵)' letters carved on the rocks, also known as the name of pavilion in Okyeonjeongsa(玉淵精舍), is the center of Okyeonsipyeong that symbolizes the enlightenment of clean noble man, as well as the symbolic locational expression of studying room. One of Okyeonsipyeong, 'Wansimjae', is assumed to be the name from the combination of two Buddhist names, 'Wanjeok(玩寂)' and 'Seshim(洗心)', 'Dangho(堂號)', lined on both sides with Wonlakjae, the residence of Seoae, as the center. Wansimjae is after all the natural feature indicating the overall Okyeonjeongsa as the core of Okyeonsipyeong with west edge Gyeomamjeongsa(謙巖精舍). Among ten Okyeonsipyeong natural features, Wansimjae(玩心齋), Ganjukmun(看竹門), Gyeomamsa(謙菴舍), Dalgwandae(達觀臺), Ssangsongae(雙松厓), and Dohwacheon (桃花遷) are on the right side of the stairway from Okyeonjeongsa to Gyeomamjeongsa, while Chuwoldam(秋月潭), Neungpadae(凌波臺), Gyeseonam(繫船巖), and Jijuam(砥柱巖) are on the road to the cliff under river cliff in Buyongdae as well as to the dock, and all are located within 500m radius close and diameter area. As the results of lexeme and context analyses of Okyeonsipyeong poet, they are mainly about Confucian teachings symbolizing the constancy of the classical scholar including ego becoming one with the nature and back to the nature, unworldliness and farsighted view, transcendence and seclusion, as well as integrity spirit. In Dohwacheon and Gyeomamsa poets, there is Tao characteristics and brotherhood that pursue fairylands such as Mooreungdowon(武陵桃源). To create tourism brand and landscape of Okyeonsipyeong, it is necessary to prepare storytelling plans including the letters carved on the rocks introduction in Buyongdae area, and also synopsis of the Silgyeongsusang musical, 'Buyongjiae(芙蓉之愛)' that is related to 10 natural features. In addition, the related plans of the experience road from Gyeseonam, which is the boat stop in Buyongdae, to Ganjukmun of Okyeonjeongsa, and again to viewing routes on the stairways to Gyeomamjeongsa using boats are necessary. For preliminary preservation and maintenance plans, the safety of the stairway from Okyeonjeongsa to Gyeomamjeongsa should be secured, the rock inscription should be preserved, landscape interpretation plates should be installed, trees and shrubs around Dohwacheon rock inscription should be removed, Dalgwandae letters carved on the rocks should be restored, and the bamboo forest outside Ganjukmun as well as Prunus persica plantation around Dohwacheon should be pointed out.

• The Journal of Fisheries Business Administration
• /
• v.26 no.2
• /
• pp.53-74
• /
• 1995

The purpose of this paper is to compare China's and Korea's marine fisheries industries in order to present the main features of China's marine fisheries and show the comparative advantages they have in production. The results indicate that China's marine fisheries have the following features. (1) The marine proportion of the fisheries industry economic activity is less than 60%. Fishing is 71.3% of that marine activity. (2) The production trends of marine fisheries history in China can be classified as follows: 1) an early growth period, 2) a deliberation/consolidation period, 3) a second growth period, 4) a third growth period, and 5) a fourth growth period. The growth rate has rapidly increased recently. (3) Fish production is over 70% of marine fishing fisheries, the next major product is crustacea. The production of shellfish occupies over 70% of marine aquaculture, seaweed production however, is only 22% of total marine aquaculture. (4) The licensed area for marine aquaculture in China is 586.3 ha and that area is 5.4 times larger than that of Korea. The allotted area for shellfish aquaculture is 60% of marine aquaculture, production areas of crustaceans occupy 27.3%, fish has 7 1%, and seaweed production only 5.7% of allocated marine aquaculture areas. (5) The proportion of power vessels for marine fisheries of China's total power vessel fleet is around 65%, and the marine fisheries portion of non - powered vessels constitutes only 12%. The highest proportion of power vessels engaged in marine fisheries activities is between 10 tonnes to 100 tonnes. (6) The portion of marine fishery workers of all fishery industry employees is 22%, and 70% of them are full - time workers. Of marine fishery workers, 64% are in the fishing sector, 22%, aquaculture workers, and the number of employees in marine fisheries is increasing every year. The analysis of China's fishery industry in the production competitiveness indicates as follows : (1) The licensed areas in marine aquaculture, number of fishing vessels, number of marine fishing workers in China's fishery industry are much more than those of Korea's. Therefore China is much more competitive than Korea in the quantity of production side. However, licensed areas for seaweed aquaculture are more extensive in Korea than China. In China, the number of power vessels of between 10 tonnes and 100 tonnes, the licensed shellfish aquaculture areas, and the number of fishing workers within the fisheries industry are much more than those of Korea. (2) It is estimated that the licensed areas in marine aquaculture, number of medium sized power vessels, number of marine fishery workers will be increased as the quantity of production factors grow in China. (3) At present, yield per Ha. in marine cultures is very low in China. Therefore it is estimated that aquaculture techniques have only been diffused recently in China. Yield of fish per Ha especially is much lower than that of Korea. So the level of aquaculture techniques seems much lower than that of Korea. (4) China is behind Korea in production technique, however the number of HP per boat in China is lower than that of Korea. Therefore, China is much more competitive than Korea in Costs. (5) Average fish catches per marine fishery worker in China is only 1/3 that of Korea's, and average marine aquaculture production in China is only 1/2 that of Korea. Therefore we can say Korea is more competitive than China in efficiency. The average income of marine fishery workers in China is higher that that of other Chinese industries. However, the competitiveness of the fisheries industry in China will be increased as more capital is invested and advanced techniques are developed.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.7 no.2
• /
• pp.161-170
• /
• 1997

This is an effort to confirm changes biological monitoring according to changes in levels of exposure to styrene for industrial workers. This study was conducted on 108 workers, including male of 64 and female 44 who were working at factories of FRP, dipping, and coating. An improved passive monitor method(organic vapor monitor; OVM) was employed to determine levels of exposure. The biological monitoring include blood styrene concentration, urinary mandelic acid(MA), and urinary phenylglyoxylic acid(PGA). Biological monitoring were made through the Collection of blood and urine. The mean value of exposure to styrene was 21.0ppm, which is measured by organic vapor monitor, one of improved passive monitors. The highest exposure level was observed among workers in boat factories, laminating procedure workers, processing workers, respectively(p<0.01). For exposure level, 11% of subjects under study showed over 50ppm which is time weighted average(TWA). The correlation coefficient between biological specimens and the exposure level was 0.62 for blood styrene concentration, 0.58 for MA corrected by creatinine, and 0.70 for PGA corrected by creatinine, respectively(p<0.01). The regression analyses found exposure level relative importance in explaining variance in biological monitoring. In additional to that, gender was a significant factor in explaining variance of MA and MA+PGA. Almost half of variance(49%) in blood styrene concentration was explained by predictors, including exposure level, age, gender, duration, and drinking volume during the last week(p<0.01). The very high correlation(higher than 0.95 was found when a comparison was made among three types of corrected methods, including uncorrected specific gravity and creatinine. In conclusion, these findings suggest OVM to represent levels of exposure to styrene for industrial workers. A discussion was made on possible use of specific gravity sample for biological monitoring. Exposure level may be predicted on MA, PGA in urine, which could be applied to represent biological monitoring.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.11 no.1
• /
• pp.31-36
• /
• 1982

Sugars and nitrogen contents and physico-chemical properties of ethanol extracts of fresh, dried, and tail ginsengs with different concentrations of the solvent were investigated. The transmittance at 550nm of fresh, dried and tail ginseng extracts (1% D.Wsoln) respectively, and all the extracts were slightly viscous-sticky, brown and pH of 4.8-6.2 Total sugars, sucrose and starch contents of the extracts were decreased with increasing of enthanol concentration as a solvent. Total sugar content of the extracts were decreased in the order of dried, tail and fresh ginseng and sucrose content were decreased in the order of fresh, driedcand tail ginsengs and starch content were decreased in the order of tail, dried and fresh ginsengs. The reducing sugar contents of the extracts were 4.9-3.8 %, 8.6-12.8 % and 7.6-9.1% in fresh, dried and tail ginsengs, respectively. Total nitrogen contents of the extracts were 2.3-4.6% in average and decreased in the order of dried, fresh and tail ginsengs.