• 대한조선학회논문집
• /
• 제43권4호
• /
• pp.504-511
• /
• 2006

In this paper a modern sailing boat for our costal area was developed by using the traditional boat hull form. Main particulars of design ship were determined by using the statistical values. Hull form was varied from the traditional boat hull form which was selected by the previous study and modified to fit Lateen sail. The appendage, rudder and keel were designed for good performance of against wind sailing. The performance of hull form was examined and the results were shown.

• 한국해양공학회지
• /
• 제22권4호
• /
• pp.78-83
• /
• 2008

In recent years, small boats used for marine leisure have been steadily increasing because of the increase in national income and the desire for marine leisure. But the repair of such small boats in dry dock has pointed out many faults in small FRP-shipbuilding in terms if workspace and manpower. Lifting a boat from the water to land is done with a crane or by hand using a sling around the bottom of the boat. But dry dock work is limited by the scale of the boat, which corresponds to the crane capacity, with carelessness making it possible to capsize a boat and endanger life. The purpose of this study was the development of a marine docking system that would improve economical efficiency and safety, for which we carried out concept design, model tests, structural analysis, etc.

• 한국해양공학회지
• /
• 제22권4호
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제2권4호
• /
• pp.217-222
• /
• 2010

Since 1980's, optimum design techniques for ship structural design have been developed to the preliminary design which aims at minimum weight or minimum cost design of mid-ship section based on analytic structural analysis. But the optimum structural design researches about the application for the detail design of local structure based on FEA have been still insufficient. This paper presents optimization technique for the detail design of a racing motor boat. To improve the performance and reduce the damage of a real existing racing boat, direct structural analyses; static and non-linear transient dynamic analyses, were carried out to check the constraints of minimum weight design. As a result, it is shown that the optimum structural design of a racing boat has to be focused on reducing impulse response from pitching motion than static response because the dynamic effect is more dominant. Optimum design algorithm based on nonlinear finite element analysis for a racing motor boat was developed and coded to ANSYS, and its applicability for actual structural design was verifed.

• 한국산학기술학회논문지
• /
• 제14권6호
• /
• pp.2559-2565
• /
• 2013

2000년 이후 FRP 보트 선체 제작에 대한 국제적 법적 규제가 강화되고 있다. 본 연구에서는 보트 선체 재료로 폴리에틸렌을 제안하였다. 폴리에틸렌은 저융점 재료로서 보트가 야외에 장기간 노출되는 경우 심각한 열피로를 받을 수 있다. 고밀도 폴리에틸렌 보트 선체에 대한 열적 내구성을 실험적으로 평가하기 위하여 삼점굽힘하중조건하에서 변형률 게이지를 이용하여 열응력을 측정한 뒤 열응력 데이터를 기초로 통계학적으로 열피로 손상을 분석하였다.

• 해양환경안전학회지
• /
• 제17권2호
• /
• pp.161-166
• /
• 2011

본 연구에서는 태양전지로 구동되는 전기추진 소형선박을 제안하여 선체의 설계 및 모형선 시험을 행하였다. 선체 모양은 배의 안정성 및 태양과의 수광면적을 고려하여 차타마란형으로 제작하였다. 계산에 의하면 설계 선박의 선속을 5 knots로 할 때 1.1마력으로 충분한 추력이 산출되었으나 실제의 선속은 태양에너지 등 기후조건에 의해 산출된 값보다 약간 낮았다.

• 전력전자학회논문지
• /
• 제21권2호
• /
• pp.182-189
• /
• 2016

A modeling method of electric power network inside a fishing boat less than 5 tons is proposed for its high-energy efficiency with renewable energy sources. The power network inside the fishing boat consists of a diesel engine, a starter motor, an alternator, battery packs, and electric loads, which are connected in parallel. To obtain proper power network model, the voltage -current characteristics of the electric components are considered to develop elaborate electrical models under several load conditions. Measured data of the battery and alternator current include noise. By using an average method, the AC components from the power network of the fishing boat can be reduced, which is verified by KCL rule. Using the proposed power network model, the power generation of the alternator and the reduction of diesel consumption in the boat's engine are predictable under various operating conditions. The validity of the proposed methodology is verified by comparing simulation results with experimental measurements using statistical inferences.

• 대한조선학회논문집
• /
• 제44권4호
• /
• pp.349-359
• /
• 2007

In this study the hull form design with minimum resistance of domestic coastal fishing boat using a computer design procedure is carried out. The target boat is G/T 4.99 ton class fishing boat. which is one of the most popular boat in the coastal sea. For the task, the design parameters needed in preliminary stage are selected or determined from the existing boat. which has excellent resistances characteristics. In the EHP estimation during the design procedure, the main objective function is the hull resistance, and the initial hull forms before the optimization are selected from the boats that are in operation now. The EHP values from the hull after optimization process are also compared with those of the original hull to confirm its effect. Also, optimizing is investigated for the hull form to reestimate such factors as stability, laboring environment for the best design. it is expected that the results of this study here can be effectively used to improve the present design status of domestic small fishing boats.

• 한국해양공학회지
• /
• 제18권4호
• /
• pp.71-76
• /
• 2004

A Study of the traditional Korean fishing boat is based on a report on an investigation of the Korean fishing boats, conducted in 1921. The report was completed in 1927 with the conclusion of the Southern Sea region and West Sea region studies, which included the investigation oj the entire region. It was a very thorough and scientific investigation of Korean fishing boats, which has been published in three volumes. Based on this report, this paper surveys the characteristics and the hull form of the traditional Korean fishing boats. As a result, we find ${\cdot}out$ that the hull form of the traditional Korean fishing boat is very similar to that of modern sailing boat. Thus, it is a good candidate for the development of the modern sailing boats for the Korean Sea.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2003년도 춘계공동학술대회논문집
• /
• pp.16-20
• /
• 2003

최근 어선어업 주변환경의 급속한 변화는 기존 어선어업의 구조조정과 새로운 사회, 경제적 환경에 부응하는 선형개발의 요구로 이어지고 있다. 한편, 서ㆍ남해 연안에서 작업 및 항해하는 연안어선들은 노출된 프로펠러에 어망, 로프 등이 감기는 사고가 매년 증가하고 있는 실정이다. 본 연구는 이상과 같은 관점에서 연안어선의 해난사고 방지를 위해 기존 선미형상을 수정한 프로펠러 보호터널 부착 연안어선을 대상으로 모형시험을 통하여 세미워터제트형 연안어선의 주요성능을 분석, 검토한 것이다.