• The Magazine of the IEIE
• /
• v.29 no.9
• /
• pp.18-30
• /
• 2002

Wireless communication systems will be one of the biggest drivers of semiconductor products over the next decade. Global Positioning System (GPS) and Blue-tooth, HomeRF, and Wireless-LNA system are just a few of RF-module candidate awaiting integration into next generation mobile phone. Motivated by the generation mobile phone. Motivated by the growing needs for low-cost and multi-band/multi-function single chip wireless transceivers, CMOS technology has been recognized as a most promising candidate for the implementation of the future wireless communication systems. This paper presents recent developments in RF CMOS technology, which is classified into device technology and circuit technology and from them forecasts technology and from them forecasts technology trends in the near future.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.2
• /
• pp.161-161
• /
• 2020

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.1
• /
• pp.35-38
• /
• 2015

LEDs are considered to be an alternative for enhancement of energy efficiency, applied for numerous areas such as display, automotive headlight not only lights. Yellow phosphor is generally utilized with blue LEDs to generate WLED, $Y_3Al_{5}O_{12}:Ce^{3+}$ is typically used as the yellow phosphor. The phosphor, mixed with epoxy resin, has been used by being spread and hardened on the blue LED chip. This paste-based packaging gives rise to problems of degradation of phosphor by heat and decrease of luminous efficiency. Although phosphor plate is used instead of the epoxy-phosphor mixture to solve these problems, loss of luminous efficacy by total internal reflection inside the plate also should be solved. In this study, we coated the side of the plate with silver as one of the solution.

• Journal of the Korean Vacuum Society
• /
• v.21 no.3
• /
• pp.164-170
• /
• 2012

The dependance of degradation on the blue-peak wavelength is investigated with the blue light-emitting diode (LED) of InGaN/GaN with respect to the optical and the electrical characteristics of the devices. The LED devices emitting the blue-peak wavelength ranging from 437 nm to 452 nm is prepared to be stressed for a long aging time with three different currents of 60 mA, 75 mA and 90 mA, respectively. The degradation of optical intensity is observed with and without phosphor in the devices. The device without phosphor has been degraded significantly as the wavelength of blue-peak is decreased while the optical intensity of LED device with phosphor become less sensitive than that of device without phosphor. The electrical property does not depend on the emission peak wavelength. However, the series-resistance of LED device is slowly increased as the aging time is increased. The deformation of device is observed severely the short wavelength of blue-peak even with the same current since the short wavelength is absorbed substantially at the materials of device during the aging time. Consequently, in order to enhance the lifetime of LED devices, it is important to understand the optical degradation property of the materials against the specific wavelengths emitted from the blue chip.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1285-1285
• /
• 2015

현재 전력난에 의해 에너지 절감이라는 말은 가정 및 산업 현장 곳곳에서 들을 수 있다. 에너지 절감 대책 중 하나가 몇 년전 정부에서 발표한 백열등 수입 및 유통금지가 있다. 그 효과로 LED 산업이 각광 받게 되었다. 다양한 LED 산업 및 기술에서도 신뢰성 및 성능 분야는 항상 진화하고 많은 기업들이 집중하고 있다. LED에서 중요한 요소인 방열성능을 개선시키기 위해 많은 연구를 행하고 있다. 그리고 광원 개발분야에서도, 반도체 광원의 LED PKG의 다량 실장으로 고출력을 행하는 것 보다는 기판위에 Blue Chip을 실장하여 제작하는 고출력 광원의 기술로 집중되고 있다. 이 논문에서는 고출력 광원인 COB(Chip On Board) LED의 방열성능 개선을 다루었다. 기판의 구조 변형으로 방열특성 개선 대안을 제시하였다. Via hole과 Cavity를 이용한 구조를 제안하였다. 그에 대한 해석 방법으로는, 구조적인 해석과 수치적인 해석을 활용하였다. 그 결과로는 약 13~40%의 방열성능 개선을 나타내었다.

• BioChip Journal
• /
• v.12 no.4
• /
• pp.326-331
• /
• 2018

Contamination by pesticides is an everincreasing problem associated with fields of environmental management and healthcare. Accordingly, appropriate treatments are in demand. Pesticide detection methods have been researched extensively, aimed at making the detection convenient, fast, cost-effective, and easy to use. Among the various detecting strategies, paper-based assay is potent for real-time pesticide sensing due to its unique advantages including disposability, light weight, and low cost. In this study, a paper-based sensor for chlorpyrifos, an organophosphate pesticide, has been developed by layering three sheets of patterned plates. In colorimetric quantification of pesticides, the blue color produced by the interaction between acetylcholinesterase and indoxyl acetate is inhibited by the pesticide molecules present in the sample solutions. With the optimized paper-based sensor, the pesticide is sensitively detected (limit of detection =8.60 ppm) within 5min. Furthermore, the shelf life of the device is enhanced to 14 days after from the fabrication, by treating trehalose solution onto the deposited reagents. We expect the paper-based device to be utilized as a first-screening analytic device for water quality monitoring and food analysis.

• ETRI Journal
• /
• v.45 no.1
• /
• pp.163-170
• /
• 2023

We report an electroabsorption modulator (EAM)-integrated distributed Bragg reflector laser diode (DBR-LD) capable of supporting a high data rate and a wide wavelength tuning. The DBR-LD contains two tuning elements, plasma and heater tunings, both of which are implemented in the DBR section, which have blue-shift and red-shift in the Bragg wavelength through a current injection, respectively. The light created from the DBR-LD is intensity-modulated through the EAM voltage, which is integrated monolithically with the DBRLD using a butt-joint coupling method. The fabricated chip shows a threshold current of approximately 8 mA, tuning range of greater than 30 nm, and static extinction ratio of higher than 20 dB while maintaining a side mode suppression ratio of greater than 40 dB under a window of 1550 nm. To evaluate its modulation properties, the chip was bonded onto a mount including a radiofrequency line and a load resistor showing clear eye openings at data rates of 25 Gb/s nonreturn-to-zero and 50 Gb/s pulse amplitude modulation 4-level, respectively.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.24-24
• /
• 2003

Research activity in the III-V nitrides materials system has increased markedly in the past several years ever since high-brightness blue light-emitting diodes (LEDs) became commercially available. Despite of excellent optical properties of the GaN, however, inherently poor thermal property of the sapphire used as a substrate material n these devices may lead to thermal degradation of devices, especially during their high power operation. Therefore, dependable thermal analysis and packaging schemes of GaN-based LEDs are necessary for solid lighting applications under high power operation. In this paper, emphasis will be placed upon thermal design of GaN-based LEDs. Thermal measurements of LEDs on chip and packaging scale were performed using the liquid crystal thermographic technology and micro thermocouples for different bias conditions. By a series of optical arrangement, hot spots with specific transition temperatures were obtained with increasing input power. Thermal design of LEDS was made using the finite element method and analytical unit temperature profile approach with optimal boundary conditions. The experimental results were compared to the simulated data and the results agree well enough for the establishment of dependable prediction of thermal behavior in these devices. The paper will present a more detailed understanding of the thermal analysis of the GaN-based blue and white LEDs for high power applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.347-348
• /
• 2008

The main goal of this work is advances in 1.0mm $\times$ 0.5mm light emitting diode using AlInGaN cell structure and display module. In the first place, we proposed $200{\mu}m{\times}200{\mu}m$ cell structure using AlInGaN. Secondly, we describe new type 1.0mm $\times$ 0.5mm blue and white LED fabrication procedure and results of an examination include mobile application.

• 한국가시화정보학회:학술대회논문집
• /
• 2004.12a
• /
• pp.65-74
• /
• 2004

Measurement of concentration distributions of suspended particles in a micro-channel is out of the most crucial necessities in the area of Lab-on-a-chip to be used for various bio-chemical applications. One most feasible way to measure the concentration field in the micro-channel is using micro-LIF(Laser Induced Fluorescence) method. However, an accurate concentration field at a given cross plane in a micro-channel has not been successfully achieved so far due to various limitations in the light illumination and fluorescence signal detection. The present study demonstrates a novel method to provide an ultra thin laser sheet beam having five(5) microns thickness by use of a micro focus laser line generator. The laser sheet beam illuminates an exact plane of concentration measurement field to increase the signal to noise ratio and considerably reduce the depth uncertainty. Nile Blue A was used as fluorescent dye for the present LIF measurement. The enhancement of the fluorescent intensity signals was performed by a solvent mixture of water $(95\%)$ and ethanol (EtOH)/methanol (MeOH) $(5\%)$ mixture. To reduce the rms errors resulted from the CCD electronic noise and other sources, an expansion of grid size was attempted from $1\times1\;to\;3\times3\;or\;5\times5$ pixel data windows and the pertinent signal-to-noise level has been noticeably increased accordingly.