• Journal of Korean Society of Rural Planning
• /
• v.18 no.1
• /
• pp.17-28
• /
• 2012

Functional mismatch and thought and plan-less material use of recently built boundary barriers in rural areas should greatly degrade their amenity value as one of linear villagescapes, but, their present state-of-art basically necessary for problem-solving had never surveyed up to now. From this point of view, this study tried to investigate present stock quantities and qualities of boundary barriers in rural areas by sample studies on 21 case villages(7 types ${\times}$ 3 cases) and comparative analysis between the planned or improved and nots. Wall type was absolutely dominated in the structural terms, of which more than half was used cement block as building material and, therefore, grey-colored. More than half of total barrier length were fully shielded, while relatively partially shielded in the mountainous villages in open space and 'Cultural villages' with closed housing structures. Free standing style of barriers was shown along over two thirds of their total length, although not more than half in planned reclaimed villages. Especially, because of one-sided wall type structure, mismatched over-shieldness and poorer maintenance condition of the boundary barriers in peri-urban villages, there should be provided with very intensive improvement efforts for amenity barriers.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1254-1263
• /
• 1990

The temperature distribution and heat flux of the inner cylinder wall of a 4-cycle turbocharged gasoline engine were calculated by a 2-dimensional coordinate transformation. Boundary conditions of the inner wall of the cylinder were taken from the results of diagnostic engine simulations. Results show that the ununiformity of inner wall temperature of the cylinder black can be reduced by a proper choice of the thickness of fin and the distance between two cylinder blocks.

• Journal of the Korean Geosynthetics Society
• /
• v.6 no.1
• /
• pp.27-32
• /
• 2007

This paper describes the applicability of geogrid with I-type coupling system, which permits vertical displacement on back fill ground of the reinforced retaining wall and also minimize the damage between block and geogrid. The improvement of coupling method allowed the reduction of approximately 700 mm in the existing geogrid, and as a result, the tensile strength at the coupling joint showed approximately 53% of the maximum tensile strength. It is expected from the laboratory investigations that the coupling strength of geogrid with the combination of in-situ supporting material should be predominant in the field condition.

• Geomechanics and Engineering
• /
• v.17 no.6
• /
• pp.515-525
• /
• 2019

The calculation of active earth pressure behind retaining wall is a typical three-dimensional (3D) problem with spatial effects. With the help of limit analysis, this paper firstly deduces the internal energy dissipation power equations and various external forces power equations of the 3D retaining wall under the nonlinear strength condition, such as to establish the work-energy balance equation. The pseudo-static method is used to consider the effect of earthquake on active earth pressure in horizontal state. The failure mode is a 3D curvilinear cone failure mechanism. For the different width of the retaining wall, the plane strain block is inserted in the symmetric plane. By optimizing all parameters, the maximum value of active earth pressure is calculated. In order to verify the validity of the new expressions obtained by the paper, the solutions are compared with previously published solutions. Agreement shows that the new expressions are effective. The results of different parameters are given in the forms of figures to analysis the influence caused by nonlinear strength parameters.

• Journal of the Korean Institute of Gas
• /
• v.12 no.4
• /
• pp.14-20
• /
• 2008

In this numerical study, the leakage safety of the LNG tank in which is constructed by membrane inner tank-plywood-polyurethane form-plywood-prestressed concrete structures has been presented for four leakage analysis models. The LNG leak criterion of the tank wall with a storage capacity of $200,000\;m^3$ is analyzed based on the thermal resistance technique. This means that if the cryogenic temperature of a leaked LNG is detected at the outer side of the PC wall, it may be leaked through the wall thickness of the tank. The calculated results based on the thermal resistance method between two walls show that the plywood, PUF, and another plywood walls may block the leakage of the leaked LNG even though the strength of these walls is already collapsed by a leaked LNG pressure. But, the leaked LNG may pass the thickness of the prestressed concrete wall for a period of elapsed time even though the PC outer tank supports the leaked LNG pressure. Thus, the PC outer tank may extend the leakage time of a leaked LNG.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.1
• /
• pp.56-63
• /
• 2018

The present study examined the reversal cyclic flexural behavior of walls with jacket section approach for seismic strengthening through forming the boundary elements at both ends of the wall. The prestressed wire ropes were used for the lateral reinforcement to confine the boundary element of the wall. The main parameter investigated was the height of the jacket section for strengthening. The limit height of the strengthening jacket section was determined by comparing the moment distributions between the existing and strengthened walls. Test results showed that the examined jacket section approach was significantly effective in enhancing the flexural resistance of walls, indicating 46% higher stiffness at peak strength and 210% greater work damage indicator, compared with the flexural performance of the unstrengthened wall. The ductility of the strengthened walls was insignificantly affected by the height of the jacket section when the height is greater than twice the wall length. The flexural capacity of the strengthened walls was 22% higher than the predictions obtained using the equivalent stress block specified in ACI 318-14.

• Journal of the Korean Magnetics Society
• /
• v.13 no.4
• /
• pp.176-181
• /
• 2003

The magnetic domain walls at the edges of a large patterned and exchanged-biased NiO(10-60 nm)/NiFe(10 nm) bilayers and their motions with applied field were investigated by magnetic force microscopy. Three kinds of domain walls, namely, head-to-head zig-zag and tail-to-tail zig-zag Bloch walls and straight Neel walls were found at specific edges of the unidirectional biased NiO(30 nm)/NiFe(10 nm) bilayer having the exchange biasing field (H$\sub$ex/) of 21 Oe. No walls were observed for the strong exchange-biased bilayer (60 nm NiO, H$\sub$ex/ = 75 Oe), while the amplitude of the zig-zag domain increased with decreasing exchange biasing. This may be explained by mutual restraint between H$\sub$ex/ and the demagnetization field of edge. We similarly investigated the magnetization reversal process, the subsequent motion of the walls and identified the pinning and nucleation sites during reversal.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2007.11a
• /
• pp.119-122
• /
• 2007

TRUTEC building, which is located at DMC B block is zone, is just one the office building in Soeul. TRUTEC building is designed by Barkow Leibinger Architeken in Germany, has 5 stories under and 12 stories above and has been finished with the unique three dimensional curtain wall unit. Big trial to make unique elevation succeeded as getting rid of the typical plain curtain wall unit. In addition, aluminum bars are treated by the latest CNC machine in order to achieve 3D section. Construction of curtain wall is highly focused from the moment of contract to keep the schedule because the contract period is 18 months. Regular design meeting and technical meeting between stakeholders including construction manager, designer, engineer, consultant and so on have been held during the construction to minimize the risks from the unique elevation and trial. Step by step mock-up test (design mock-up and visual mock-up on site) has been performed before functional mock-up test.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.09a
• /
• pp.53-58
• /
• 2000

The KOESWall system that minimizes the horizontal deformation of reinforced wall effectively was developed bt E&S Eng. Co., Ltd. in 1999. Due to its systematical feature i.e. isolated construction method. KOESWall system is able to use as temporary structures more economically without the facing block. In this report, it is shown that the case history of KOESWall as a temporary soil retaining structure and the field measuremnets.

• International Journal of Ocean System Engineering
• /
• v.3 no.2
• /
• pp.95-101
• /
• 2013

This study is mainly interested in roundness of a circular moonpool structure in FPSO. Because this structure needs abrasion-resistance on inner wall, we should do buttering widely and deeply by using Inconel. But a general buttering can cause a severe distortion at structures. If someone can analyze the roundness by thermal distortion under Inconel over-lay, an erection policy can be established. In this study, shrinkage methodology by designed stress-strain curve was used and the result allowed deciding an appropriate block size.