• Journal of Biosystems Engineering
• /
• v.33 no.1
• /
• pp.14-20
• /
• 2008

An agricultural unmanned helicopter was suggested for an alternative to current pesticide application methods to solve such problems as high cost, low efficiency, shirking task and unsafe work. To pursuit this trend, researches on the development of unmanned helicopters have been accelerated in Korea as well. In this research, a guide type centrifugal clutch that plays an important role in the unmanned helicopter was studied. Theoretical analyses and experimental tests were conducted for designing an optimal clutches. Main design factors of the guide type centrifugal clutch were found to be spring constant, free length of spring, mass of friction sector, contact area, allowable pressure, number of friction sector, friction coefficient, radius of drum, and clutch arrangement. And these design factors could be the functions of engaging engine speed and desired power transfer capacity. The result of the single clutch test showed the power transfer capacity of 14.1 PS at 5,800 rpm and the result of the dual clutch test showed that the capacity of 17.7 PS at 5,600 rpm. These experimental results agreed well the theoretical simulations.

• ETRI Journal
• /
• v.39 no.1
• /
• pp.87-96
• /
• 2017

Ultrasonic surgical devices are routinely used for surgical procedures. The incision and coagulation of tissue generate a temperature of $40^{\circ}C-150^{\circ}C$ and depend on the controllable output power level of the surgical device. Recently, research on the classification of grasped tissues to automatically control the power level was published. However, this research did not consider the specific characteristics of the surgical device, tissue denaturalization, and so on. Therefore, this research proposes a robust algorithm that simulates noise to resemble real situations and classifies tissue using conventional classifier algorithms. In this research, the bioimpedance spectrum for six tissues (liver, large intestine, kidney, lung, muscle, and fat) is measured, and five classifier algorithms are used. A signal-to-noise ratio of additive white Gaussian noise diversifies the testing sets, and as a result, each classifier's performance exhibits a difference. The k-nearest neighbors algorithm shows the highest classification rate of 92.09% (p < 0.01) and a standard deviation of 1.92%, which confirms high reproducibility.

• Journal of the Korean Society of Industry Convergence
• /
• v.14 no.1
• /
• pp.29-36
• /
• 2011

This study analyzed the convenience and productivity before and after adopting self-propelled power transportation devices to the harvest and transportation of fruit and vegetable products in the Gyeongbuk region, by applying the REBA and RULA techniques. In the REBA analysis, the work risk was low with 4~6 points before adoption which became 2~3 points after adoption. As for the RULA analysis, work loading appeared to have decreased with 6~7 points before adoption which became 3~4 points after adoption. The annual work time reduction was about 48~179 hours while labor costs were reduced to 364~1,345 thousand won annually. This indicated a labor cost reduction effect of about 10~15%. Therefore, the adopted self-propelled power transportation devices appeared to prevent musculo skeletal diseases of the human body and also improve productivity even after using it for long hours according to the REBA, RULA measures level.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.806-812
• /
• 2009

Availability of reliable and affordable energy supply is a prerequisite for economic growth. Renewables are the third largest contributor to global electricity production after coal and natural gas and account for a share of 18%. Power generating capacity from renewables has increased to around 900GW by the year 2007. Today biodiesel fuels have been in commercial use in many countries and recently the world-wide biodiesel market has experienced considerable growth, which is partly due to various tax concession programs and other financial incentives. In Korea, biodiesel has already been used for transportation fuel, but not used for power generation fuel yet. Korean government has a strategy for renewable energy propagation, especially the goal of power generation amount by renewable energy is 3% of total power production by 2012. This paper focuses on the feasibility study for adaptability and strategy of using biodiesel as power generation fuel. The study also has the plan to replace the fuel of thermal power plant, gas turbine and distributed power system. As the increase of biodiesel fuel, I look forward to environment-friendly power generation and the strategy of Renewable Portfolio Standards(RPS).

• New & Renewable Energy
• /
• v.5 no.1
• /
• pp.32-39
• /
• 2009

Availability of reliable and affordable energy supply is a prerequisite for economic growth. Renewables are the third largest contributor to global electricity production after coal and natural gas and account for a share of 18%. Power generating capacity from renewables has increased to around 900GW by the year 2007. Today biodiesel fuels have been in commercial use in many countries and recently the world-wide biodiesel market has experienced considerable growth, which is partly due to various tax concession programs and other financial incentives. In Korea, biodiesel has already been used for transportation fuel, but not used for power generation fuel yet Korean government has a strategy for renewable energy propagation, especially the goal of power generation amount by renewable energy is 3% of total power production by 2012. This paper focuses on the feasibility study for adaptability and strategy of using biodiesel as power generation fuel. The study also has the plan to replace the fuel of thermal power plant, gas turbine and distributed power system. As the increase of biodiesel fuel, I look forward to environment-friendly power generation and the strategy of Renewable Portfolio Standards(RPS).

• Journal of Biosystems Engineering
• /
• v.41 no.4
• /
• pp.304-312
• /
• 2016

Purpose: Soil strength has been measured using a cone penetrometer, which is making it difficult to obtain the spatial data required for precision agriculture. Our objectives were to evaluate real-time horizontal soil strength (RHSS) to measure soil strength in real time while moving across the field. Using the RHSS data, the tillage depth was determined, and the power consumption of a tractor and rotavators were compared. Methods: The horizontal soil-strength index (HSSI) obtained by the RHSS was compared with the cone index (CI), which was measured using a cone penetrometer. Comparison analysis in accordance with the measurement depth that increased at 5-cm interval was conducted using kriged maps at six sensing depths. For tillage control and evaluation of the power consumption, the system was installed with a potentiometer for tillage depth, a torque sensor from the rear axle, and a power take-off (PTO) shaft. Results: The HSSI was lower than the CI, but they were the same at 54.81% of the total grids for the 5-cm depth and at 3.85% for the 10-cm depth. In accordance with the recommended tillage map, tillage operations between 0 and 15 cm left 2.3% and 7% residue cover on the soil, and that between 20 and 10 cm covered a wider utilization of 3% and 18.4%, respectively. When the tillage depth was 15 cm, the comparison result of the power requirements between the PTO and rear axle in terms of control performance revealed that the maximum power requirements of the axle and PTO were 44.63 and 23.24 kW, respectively. Conclusions: An HSSI measurement system was evaluated by comparison with the conventional soil strength measurement system (CI) and applied to a tractor to compare the tillage power consumption. Further study is needed on its application to various farm works using a tractor for precision agriculture.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.9
• /
• pp.4229-4233
• /
• 2012

With the advances in modern diagnostic expertise for cancer, certain approaches allowing scanning of the complete genome and the proteome are becoming very useful for researchers. These high throughput techniques have already proven power, over traditional detection methods, in differentiating disease sub-types and identifying specific genetic events during progression of cancer. This paper introduces major branches of omics-technology and their applications in the field of cancer. It also addresses current road blocks that need to be overcome and future possibilities of these methods in oncogenic detection.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.8
• /
• pp.582-588
• /
• 2008

An experimental investigation was conducted to investigate the effect of Bio-ethanol fuel on the engine performance and exhaust emission characteristics under various engine operating conditions. To investigate the effect of bio-ethanol fuel, the commercial 1.6L SI engine equipped with 4 cylinder was tested on EC dynamometer. The engine performance including brake torque, brake specific fuel consumption, and barke specific energy consumption of bio-ethanol fuel was compared to those obtained by pure gasoline. Furthermore, the exhaust emissions were analyzed in terms of regulated exhaust emissions such as unburned hydrocarbon, oxides of nitrogen, and carbon monoxide.Result of this work shows that the effect of blending of ethanol to gasoline caused drastic decrease of emissions under various operating conditions. Also, improved engine performance such as brake torque and brake power were indicated for bio-ethanol fuel.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.2
• /
• pp.294-301
• /
• 2017

This paper presents a low power ${\Sigma}{\Delta}$ modulator for an implantable chip to acquire a bio-signal such as EEG, DBS, and EMG. In order to reduce a power consumption of the proposed fourth order modulator, two op-amps utilized for the first two integrators are reconfigured to drive the second two integrators. The KT/C noise reduction circuit in the first two integrators is employed to enhance SNR of the modulator. The proposed circuit was fabricated in a 0.18 um CMOS n-well 1 poly 6 metal process with the active chip core area of $900um{\times}800um$ and the power consumption of 830 uW. Measurement results were demonstrated to be SNDR of 76 dB, DR of 77 dB, ENOB of 12.3 bit at the input frequency of 250 Hz and the clock frequency of 256 kHz. FOM1 and FOM2 were measured to be 41 pJ/step and 142.4 dB, respectively.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.2
• /
• pp.111-117
• /
• 2004

The low-power design of the A/D converter is indispensable to achieve the compact bio-signal measuring device with long battery duration. In this paper, new decimation filter structure is proposed for the low-power design of the Sigma-Delta A/D converter in the bio-instruments. The proposed filter is based on the non-recursive structure of the CIC (Cascaded Integrator Comb) decimation filter in the Sigma-Delta A/D converter. By combining the CSD (Canonic Signed Digit) structure with common sub-expression sharing technique, the proposed decimation filter structure can significantly reduce the number of adders for implementation. For the fixed decimation factor of 16, the 15％ of power consumption saving is achieved in the proposed structure in comparison with that of the conventional polyphase CIC filter.