• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1237-1239
• /
• 2005

In this study, we estimate the thermal conductivity of stainless steel reinforced Bi-2223/Ag tape which was made from American Superconductor. The equipments for thermal conductivity measurement was set up using conduction cooled cryocooler. Two direction of thermal conductivity was measured. The one is the direction of cut length, and the other is direction of transverse of wounded coil with insulation material. It was observed that the thermal conductivity of transverse direction of coil was extremely lower than that of cut length direction. It was mainly seems that superconducting filaments and insulation material were effected on thermal conductivity in thermal conductivity of transverse direction.

• Progress in Superconductivity and Cryogenics
• /
• v.2 no.2
• /
• pp.15-19
• /
• 2000

The stability of variable cross-sectional area HTS current lead is considered. The cross-sectional area is varied to have a constant safety factor which is defined as the ratio of operating current and critical current of superconductor. As the constant area HTS lead, the variable cross-sectional area HTS lead also has three steady states above the bifurcation point and only one steady state below the bifurcation point. The temperature profiles and current sharing ratios for each steady state are calculated. The heat dissipation into cryogenic system for super-conducting, intermediate, and upper states are compared. For Bi-2333 sheathed with silver-gold alloy 2m length of current lead, and the maximum temperature of upper state seems to be burn-out free below 5m length.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.58-63
• /
• 1992

Effects of the second sintering process on the superconducting characteristics of the (Bi, Pb)SrCaCuO system have been studied. It was found that the optimal calcining temperature of mixed powder may be proper to 820$^{\circ}C$ and the optimal sintering temperture was determined on 845$^{\circ}C$. The 2212 phases transitioned the 2223 phasses during the sintring process and zero resistance was attained at 108 K for the samples sintered for 264 hr. The 2223 phases changed into the 2212 phases and nonsuperconducting phases by the second grinding process. And the 2223 phases did not recover easily by the second sintering process.

• Progress in Superconductivity and Cryogenics
• /
• v.25 no.2
• /
• pp.5-9
• /
• 2023

The effect of La_0.7Sr_0.3MnO₃ (LSMO) addition on the superconducting property of Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_10+δ ((Bi, Pb)-2223) polycrystalline samples was studied. LSMO (0.3 wt.% to 2.0 wt.%) added (Bi, Pb)-2223 samples were prepared by using a solid-state reaction method. The XRD analyses show that as the LSMO addition increases, the volume fraction of the Bi-2223 phase is gradually decreased. The critical temperature (T_c) exhibits a gradual decrease with a single transition as the LSMO amount increases up to 1.0 wt.%, but a further addition of LSMO induces an abrupt decrease of T_c with a dual transition. The analyses on the local structure of the CuO₂ plane from the X-ray absorption fine structure (EXAFS) measurements showed that for the samples with low concentration of LSMO up to 1.0 wt.%, the Cu-O bond length and the CuO₂ plane ordering do not degrade from the values of pure (Bi, Pb)-2223, while they get worsen with a further increase of LSMO addition. These results open up the possibility of LSMO as artificial pinning centers of the (Bi, Pb)-2223 system for power application.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.1
• /
• pp.44-47
• /
• 2012

The substantial improvement of the signal-to-noise ratio (SNR) can be achieved with small-size samples or low-field MRI system by high-temperature superconducting(HTS) RF coil. The typical HTS RF coil made of HTS thin film is expensive and is limited the coil geometry to planar surface coil. In this study, commercial Bi-2223 HTS tapes was used as RF coil for a 0.35T permanent MRI system. It has advantages of both much lower cost and easier fabrication over HTS thin film coil. SNR gain of the image obtained from the HTS RF coil over a conventional Cu RF coil at room temperature was about 2.4-fold and 1.9-fold using the spin echo pulse sequence and gradient echo pulse sequence respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.97-100
• /
• 2004

In this paper, the preparation of BSCCO superconducting wire by electrophoretic deposition method and the effect of suspension medium used with various solvent solutions of ethanol and buthanol for electrophoretic deposition were studied. The preheating technique in vacuum system for the superconducting powders coated on Ag wire was also investigated. As a result, it was confirmed that the preheating technique was very useful to remove the influence of remains affected to the surface conditions of superconducting wire. And the adsorbed solvent solution which was existed between and on the deposited particle surfaces was almost disappeared at the treating conditions of about $10^{-3}$ Torr and around $200^{\circ}C$ in bell-jar system. By measurement of 4-point prove method, the critical current density($J_c$) of BSCCO superconducting wire was obtained at the value of more than $10^4\;A/cm^2$ in liquid $N_2$(77 K, 0 T).

• Journal of the Korean Ceramic Society
• /
• v.40 no.6
• /
• pp.530-538
• /
• 2003

Samples with the nominal composition, B $i_{1.84}$P $b_{0.34}$S $r_{1.91}$C $a_{2.03}$C $u_{3.06}$ $O_{10+}$$\delta$/ (110 K phase) high $T_{C}$ superconductors containing MgO as an additive were fabricated by a solid-state reaction method. Samples with 5~50 wt％ MgO were sintered at 820~86$0^{\circ}C$ for 24 h. The structural characteristics, critical temperature and grain size of the samples with different MgO contents were analyzed by XRD and SEM. As the MgO content increased, the intensity of MgO peaks and ratio of Bi-2212 phase in superconductors were intensified and the proportion of the phase transition from Bi-2223 to Bi-2212 was increased.d.creased.d.

• Journal of the Korean Ceramic Society
• /
• v.34 no.10
• /
• pp.1083-1091
• /
• 1997

As one of the chemical powder fabrication methods, the powder preparation method by using oxalate has the following advantages; (1) easy to control the chemical stoichiometry, (2) easy to fabricate homogeneous and fine particles, and (3) easy to be thermaly decomposed at low temperature. In the present study, the initial morphology and size distribution of the powder were controlled and the homogeniaty was improved. By carefully controlling the pH with NH4OH, the Bi(Pb)-Sr-Ca-Cu-O superconducting powders were prepared and investigated for their properties. The microstructures and the superconducting properties of the pelletized samples were investigated. Also, the microstructures and electrical properties of the samples prepared by tape casting method were investigated. The fabricated powders were spherical with less than 400 nm, but most of them were agglomerated to be 1~3 ${\mu}{\textrm}{m}$ in size. The critical temperature of the pelletized sample annealed at 84$0^{\circ}C$ for 72 hours in air was 110K. And the critical currents of annealed samples in air prepared by tape casting process for 24 hours and 72 hours were 0.6 A (Jc=600A/$\textrm{cm}^2$) and 1.9A (Jc=1, 900A/$\textrm{cm}^2$) respectively.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.4
• /
• pp.1-5
• /
• 2019

We investigated the effect of Fe₃O₄ addition on the critical temperature of (Bi, Pb)-2223 polycrystalline samples. Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_10+δ + x wt. % Fe₃O₄ (x = 0.0, 0.2, 0.4, 0.6, and 0.8) samples were prepared by using a solid-state reaction method. The analysis of X-ray diffraction data indicates that as Fe₃O₄ is added, dominant phase of the sample changes from Bi-2223 to Bi-2212 with an increasing Bi-2201 phase. The transition temperature of the samples drastically decreased with the Fe₃O₄ addition. The resistance data of samples with x = 0.2 and 0.4 showed a double transition indicating a coexistence of Bi-2223 and Bi-2212 phase while the samples with x = 0.6 and 0.8 showed a single transition with a semiconducting behavior. This phase transition may originate from changes in local structure of the Bi-2223 system by Fe₃O₄ addition. Analysis of the pair distribution function of the Cu-O pair in the CuO₂ plane calculated from extended X-ray absorption fine structure data revealed that the oxygen coordination of copper ion changes from CuO₄ planar type (x = 0.0 - 0.4) to CuO₅ pyramidal type (x = 0.6, 0.8). The correlated Debye-Waller factor, providing information on the atomic disorder within the CuO₂ plane, shows an inverse relation to the coordination number. These results indicate that addition of Fe₃O₄ changes the oxygen distribution around Cu in the CuO₂ plane, causing a phase transition from Bi-2223 to more stable Bi-2212/Bi-2201 phases.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.2
• /
• pp.42-45
• /
• 2001

An ozone condensation system is evaluated from the viewpoint of an ozone supplier for Bi-superconductor thin film growth. An ozone condenser by a selective adsorption on the silica gel surface is constructed. Ozone density is evaluated by three methods; ultraviolet absorption, thermal decomposition and Q-mass analyzing methods. Thermal decomposition method is found to be available to the density evaluation from dilute to highly condensed ozone. The highest ozone density condensed by the adsorption method is evaluated to be 97 mol%.