• 한국생산제조학회지
• /
• 제18권4호
• /
• pp.362-368
• /
• 2009

In general, circuit board assemblies experience various mechanical loadings during assembly and in actual use. The repeated cyclic bending can cause electrical failures due to circuit board cracks, solder interconnects cracks, and the component cracks. In this paper, we report on the failure characteristics of semiconductor chips under the repeated cyclic bending. We first describe a new 4-point bending tester, which is developed according to JEDEC standard No. 22B113. The performance of the tester is then estimated through actual experiments. Test results reveal that the cracks first occur on the outer balls around 20,000 cycles and gradually propagate to the inner balls where cracks are found around 70,000 cycles.

• Steel and Composite Structures
• /
• 제31권4호
• /
• pp.329-340
• /
• 2019

An innovated type of the flat steel plate-lightweight aggregate concrete hollow composite slab was presented in this paper. This kind of the slab is composed of flat steel plate and the lightweight aggregate concrete slab, which were interfaced with a set of perfobond shear connectors (PBL shear connectors) with circular hollow structural sections (CHSS) and the shear stud connectors. Five specimens were tested under static monotonic loading. In the test, the influence of shear span/height ratios and arrangements of CHSS on bending capacity and flexural rigidity of the composite slabs were investigated. Based on the test results, the crack patterns, failure modes, the bending moment-curvature curves as well as the strains of the flat steel plate and the concrete were focused and analyzed. The test results showed that the flat steel plate was fully connected to the lightweight aggregate concrete slab and no obvious slippage was observed between the steel plate and the concrete, and the composite slabs performed well in terms of bending capacity, flexural rigidity and ductility. It was further shown that all of the specimens failed in bending failure mode regardless of the shear span/height ratios and the arrangement of CHSS. Moreover, the plane-section assumption was proved to be valid, and the calculated formulas for predicting the bending capacity and the flexural rigidity of the composite slabs were proposed on the basis of the experimental results.

• 한국산학기술학회논문지
• /
• 제18권9호
• /
• pp.492-498
• /
• 2017

본 연구는 다양한 구조적 변수에 따른 고강도 및 내진용 이형철근의 굽힘가공 성능을 실험적으로 평가하는데 그 목적이 있다. 굽힘성능에 대한 실험적 연구수행을 위해 이형철근의 강종 및 강도, 직경, 굽힘가공 각도 및 내면 반지름 등을 변수로 하여 시험체를 제작하였다. 시험은 각 변수별 원 소재 철근에 대한 1차 인장강도시험, 원 소재 철근에 대한 1차 굽힘시험과 1차 굽힘시험 철근을 대상으로 한 2차 굽힘시험 그리고 2차 굽힘시험 이후 가력이 가능한 시험체를 대상으로 한 2차 인장강도시험을 수행하였다. 금번 고강도 및 내진용 철근에 대한 실험적 연구결과 항복강도 500 MPa 및 직경 D13 이하 이형철근은 굽힘각도 $135^{\circ}$, 내면 반지름 2db의 경우에도 1차 굽힘가공 후 인장측 표면결함은 나타나지 않았으며, 이형철근의 강도와 직경이 증가할수록 굽힘가공 성능이 저하 하는 것으로 나타났다. 그리고 본 연구에서 수행된 시험에서는 일반용 철근과 특수 내진용 철근의 시험결과 비교에서 두 이형철근 간에 유의미한 구조적 성능 차이는 확인하지 못하였다.

• 한국공간구조학회논문집
• /
• 제19권3호
• /
• pp.77-83
• /
• 2019

AU(A plus U-shaped) composite beam was developed for reducing the story height in the residential buildings, and saving the cosrtuction cost of floor structures. Structural performance and economic feasibility of the composite beam have been sufficiently approved through the structural experiments and the analytical studies. Fire safety for the practical application of the composite beam has also been verified through the fire resistance tests and the heat transfer analyses. In this study 2-points bending tests were performed on the four specimens already tested for fire resistance to evaluate the residual bending strength of AU composite beam after fire accident. The same bending test was performed on the one fresh specimen having the same section and span of the specimens for practically comparative study.

• 한국가구학회지
• /
• 제22권4호
• /
• pp.323-329
• /
• 2011

In our country, domestic species can not be used as a structural member because we have not yet grading system. So, to utilize as a basic data of grading system, bending test and numerical modelling on structural member were conducted in this study. 35 of Douglas-fir, 2" ${\times}$ 6", span 2.4 m were tested for the bending properties, and Ansys software was used to analyze the numerical modelling on the structural members. The data of knots were inspected and applied in numerical modelling. To obtain the accuracy of analysis, nonlinear numerical analysis was carried out instead of linear numerical analysis. Ultimate load had a wide range from 4883N to 11,738 N, and maximum deformation also had a range from 26 mm to 68 mm. Average of ultimate load was 8,616 N, and that of maximum deformation was 48 mm. The distinctive features of failure types were simple tension type and cross-grain tension type. Ulitmate load and maximum deformation from numerical modelling were 7,504 N and 37 mm. The numerical modelling drawn by this study is available to all species, and reasonable prediction on the bending performance is possible with only some material properties.

• 한국강구조학회 논문집
• /
• 제28권6호
• /
• pp.403-414
• /
• 2016

최근 강재가격 하락과 인건비 상승으로 강구조 및 합성구조의 연구가 활발히 진행되고 있다. 이에 본 연구에서는 보 춤이 큰 고성능 하이브리드 합성보에 대해 10개의 실험체를 제작하여 휨성능을 평가하였다. 휨 실험 결과 공칭하중에 대한 최대하중의 비($P_u/P_n$)는 평균 1.19배로 안정적인 내력을 확보하였으며, 변형능력(${\delta}_{0.8P_u}/{\delta}_y$)은 약 3.9~4.5배의 범위로 확인되었다. 또한 하이브리드 합성보의 내력평가는 현행 건축구조기준(KBC 2009)을 적용하여 평가하는 것이 적절한 것으로 판단된다.

• Structural Engineering and Mechanics
• /
• 제85권3호
• /
• pp.407-417
• /
• 2023

Precast assembled bridge piers with hybrid connection (PASP) use both tendons and socket connections. To study the seismic performance of PASP, a full-scale in-situ test was performed based on an actual bridge project. The elastic-plastic fiber model of PASP was established using finite element software, and numerical analyses were performed to study the influence of prestress degree and socket depth on the PASP seismic performance. The results show that the typical failure mode of PASP under horizontal load is bending failure dominated by concrete cracking at the joint between the column and cushion cap. The cracking of the pier concrete and opening of joints depend on the prestress degree and socket depth. The prestressing tendons and socket connection can provide enough ductility, strength, restoration capability, and bending strength under small horizontal displacements. Although the bearing capacity and post yield stiffness of the pier can be improved to some extent by increasing the prestressing force, ductility is reduced, and residual deformation is increased. Overall, there are reasonable minimum socket depths to ensure the reliability of the socket connection.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.171-180
• /
• 2005

Bending performances of aluminum square tube beams reinforced by aluminum plates under three point bending loads have been evaluated using experimental tests combined with theoretical and finite element analyses. A finite element simulation for the three-point bending test was performed. Basic properties of aluminum materials used for initial input data of the finite element simulation were obtained from the true stress-true strain curves of specimens which had been extracted from the Al tube beams. True stresses were determined from applied loads and cross-sectional area records of a tensile specimen with a rectangular cross-section by real-time photographing, and true strains were obtained from in-situ local elongation measurements of the specimen gage portion by the multi-point scanning laser extensometer. Six kinds of aluminum tube beam specimens adhered by aluminum plates were employed fur the bending test. The bending deformation behaviors up to the maximum load described by the numerical simulation were in good agreement with experimental ones. After passing the maximum load, reinforcing plate was debonded from the aluminum tube beam. An aluminum tube beam strengthened by aluminum plate on the upper web showed an excellent bending capability.

• 한국주조공학회지
• /
• 제34권2호
• /
• pp.60-66
• /
• 2014

A Zr-based amorphous alloy specimen was produced by vacuum die casting process. The salt spray test was carried out using the specimens in the as-cast, $Al_2O_3$ and $ZrO_2$ particle blasted state. Using these specimens, the SEM-EDX and XRD analyses, DSC measurement and bending strength test were conducted. After the salt spray test, the specimens were not experienced phase change and thermal characteristics of the alloys were remained unchanged. In the as-cast specimen, corrosion products were not observed. However, in the $Al_2O_3$ particle blasted specimen, pitting corrosion occurred and the detected corrosion products were $ZrCl_2$ and $NaZrO_3$. Due to the salt spray test, bending strength of the $Al_2O_3$ blasted specimens showed about 100 MPa lower strength than the other specimens. The bending fracture surface was vein pattern which was shown typically in the amorphous alloys.

• Journal of the Korean Wood Science and Technology
• /
• 제44권3호
• /
• pp.315-322
• /
• 2016

2개 이상의 보부재 집성재 요소들의 측면접착으로 제작된 "블록접착집성재"는 대단면 목조건축물의 건축부재로 활용 가능한 구조용재다. 블록접착집성재의 측면은 접착제의 종류와 도포량 및 압체압력을 각기 다른 조합으로 접착하여 박리시험과 전단블록시험으로 접착성능을 검토하였다. 실험결과 레조시놀접착제 $500g/m^2$을 도포하고 압체압력 1.5 MPa의 조건으로 제작된 블록접착집성재의 측면접착성능이 가장 양호하였다. 양호한 측면접착조건으로 제작된 블록접착집성재는 동일단면계수의 대조군 집성재와 휨 강도 성능을 비교 검토하였다. 블록접착집성재의 휨 탄성계수는 대조군 집성재와 유사하였으며, 파괴계수는 대조군집성재 보다 27% 향상되었다. 할렬은 대조군집성재 보다 블록접착집성재에서 다량 발생하였으며, 블록접착집성재의 측면접착층에서 계면파괴나 응집파괴는 관찰되지 않았다.