• Steel and Composite Structures
• /
• v.20 no.4
• /
• pp.833-849
• /
• 2016

Pre-stressing of existing structures using steel cables, FRP cables or FRP laminates has been successfully tried in the past. Retrofitting of beams using pre-stressed laminates does not utilize the full strength of the FRP due to de-bonding of the laminates before the fibre fracture. In the present study attempt has been made to overcome this problem by replacing the FRP laminates by the FRP sheets. In the present paper the effect of initial damage level and pre-stress level on strength, stiffness, cracking behaviour and failure mode of girders retrofitted using pre-stressed CFRP sheets has been studied. The results indicate that rehabilitation of initially damaged girders by bonding pre-stressed CFRP sheets improves the flexural behaviour of beams appreciably. However, it has been observed that with increase in pre-stressing force the load carrying capacity of the girders increases up to a particular level up to which the mode of failure is fibre fracture. Thereafter, the mode of failure shifts from fibre fracture to de-bonding and there is no appreciable increase in load carrying capacity with further increase in pre-stressing force.

• Steel and Composite Structures
• /
• v.23 no.5
• /
• pp.585-596
• /
• 2017

Tubular joints have been widely used in offshore platforms and space structures due to their merits such as easy fabrication, aesthetic appearance and better static strength. For existing tubular joints, a grouted sleeve reinforced method was proposed in this paper. Experimental tests on five tubular T-joints reinforced with the grouted sleeve and two conventional tubular T-joints were conducted to investigate their mechanical behaviour. A constant axial compressive force was applied to the chord end to simulate the compressive state of the chord member during the tests. Then an axial compressive force was applied to the top end of the brace member until the collapse of the joint specimens occurred. The parameters investigated herein were the grout thickness, the sleeve length coefficient and the sleeve construction method. The failure mode, ultimate load, initial stiffness and deformability of these joint specimens were discussed. It was found that: (1) The grouted sleeve could change the failure mode of tubular T-joints. (2) The grouted sleeve was observed to provide strength enhancement up to 154.3%~172.7% for the corresponding un-reinforced joint. (3) The initial stiffness and deformability were also greatly improved by the grouted sleeve. (4) The sleeve length coefficient was a key parameter for the improved effect of the grouted sleeve reinforced method.

• Structural Engineering and Mechanics
• /
• v.40 no.3
• /
• pp.393-410
• /
• 2011

The eight-node 3D solid element is one of the most extensively used elements in computational mechanics. This is due to its simple shape and easy of discretization. However, due to the parasitic shear locking, it should not be used to simulate the behaviour of structural members in bending dominant conditions. Previous researches have indicated that the introduction of incompatible mode into the displacement field of the solid element could significantly reduce the shear locking phenomenon. In this study, an incompatible mode eight-node solid element, which considers both geometric and material nonlinearities, is developed for modelling of structural members at elevated temperatures. An algorithm is developed to extend the state determination procedure at ambient temperature to elevated temperatures overcoming initially converged stress locking when the external load is kept constant. Numerical studies show that this incompatible element is superior in terms of convergence, mesh insensitivity and reducing shear locking. It is also showed that the solid element model developed in this paper can be used to model structural behaviour at both ambient and elevated temperatures.

• Structural Engineering and Mechanics
• /
• v.75 no.1
• /
• pp.123-131
• /
• 2020

The bond performance of glass fibre reinforced polymer (GFRP) bars and that of steel bars embedded in Alkali Activated Cement (AAC) concrete are analysed and compared using pull-out specimens. The bond failure modes, the average bond strength and the free end bond stress-slip curves are used for comparison. Tepfers' concrete ring model is used to further analyse the splitting failure in ribbed steel bar and GFRP bar specimens. The angle the bond forces make with the bar axis was calculated and used for comparing bond behaviour of ribbed steel bar and GFRP bars in AAC concrete. The results showed that bond failure mode plays a significant role in the comparison of the average bond stress of the specimens at failure. In case of pull-out failure mode, specimens with ribbed steel bars showed a higher bond strength while specimens with GFRP bars showed a higher bond stress in case of splitting failure mode. Comparison of the bond stress-slip curves of ribbed steel bars and GFRP bars depicted that the constant bond stress region at the peak is much smaller in case of GFRP bars than ribbed steel bars indicating a basic bond mechanism difference in GFRP and ribbed steel bars.

• Steel and Composite Structures
• /
• v.21 no.5
• /
• pp.1017-1029
• /
• 2016

When a welded circular hollow section (CHS) tubular joint is subjected to brace axial loading, failure position is located usually at the weld toe on the chord surface due to the weak flexural stiffness of the thin-walled chord. The failure mode is local yielding or buckling in most cases for a tubular joint subjected to axial load at the brace end. Especially when a cyclic axial load is applied, fracture failure at the weld toe may occur because both high stress concentration and welding residual stress along the brace/chord intersection cause the material in this region to become brittle. To improve the ductility as well as to increase the static strength, a tubular joint can be reinforced by increasing the chord thickness locally near the brace/chord intersection. Both experimental investigation and finite element analysis have been carried out to study the hysteretic behaviour of the reinforced tubular joint. In the experimental study, the hysteretic performance of two full-scale circular tubular T-joints subjected to cyclic load in the axial direction of the brace was investigated. The two specimens include a reinforced specimen by increasing the wall thickness of the chord locally at the brace/chord intersection and a corresponding un-reinforced specimen. The hysteretic loops are obtained from the measured load-displacement curves. Based on the hysteretic curves, it is found that the reinforced specimen is more ductile than the un-reinforced one because no fracture failure is observed after experiencing similar loading cycles. The area enclosed by the hysteretic curves of the reinforced specimen is much bigger, which shows that more energy can be dissipated by the reinforced specimen to indicate the advantage of the reinforcing method in resisting seismic action. Additionally, finite element analysis is carried out to study the effect of the thickness and the length of the reinforced chord segment on the hysteretic behaviour of CHS tubular T-joints. The optimized reinforcing method is recommended for design purposes.

• 한국해양학회지
• /
• v.27 no.1
• /
• pp.55-65
• /
• 1992

Ninety-seven surface sediment samples, collected from the southeastern part of the Yellow Sea, were analyzed for their contents of five metallic elements, including Fe, Mn, Ni, Cu and Pb as well as their grain-size and calcium carbonate content. The result showed a contrasting behaviour among the five metallic elements. with respect to their relationship with the sediment grain0size. contents of nickel and copper demonstrated a fairly linear relationship with the pediment grain-size whereas those of manganese and lead did not. This different behaviour in these metals was interpreted as being the result of the anthropogenic inputs (for Pb) and modification during the early diagenesis (for Mn). The R0mode factor analysis result also confirmed the different behaviour of manganese and lead from that of copper and nickel. Based on this different behaviour in metals the (Mn+Pb)/(Cu+Ni) ratio was suggested as a possible criterion for distinguishing the fine sediments in the study area, which originated from two different source area. China and Korea.

• Steel and Composite Structures
• /
• v.46 no.4
• /
• pp.497-512
• /
• 2023

Using light weight concrete as infill material in conventional cold-formed steel (CFS) shear wall systems can considerably increase their load bearing capacity, ductility, integrity and fire resistance. The compressive strength of the filler concrete is a key factor affecting the structural behaviour of the composite wall systems, and therefore, achieving maximum compressive strength in lightweight concrete while maintaining its lightweight properties is of significant importance. In this study a new type of optimum polystyrene lightweight concrete (OPLC) with high compressive strength is developed for infill material in composite CFS shear wall systems. To study the seismic behaviour of the OPLC-filled CFS shear wall systems, two full scale wall specimens are tested under cyclic loading condition. The effects of OPLC on load-bearing capacity, failure mode, ductility, energy dissipation capacity, and stiffness degradation of the walls are investigated. It is shown that the use of OPLC as infill in CFS shear walls can considerably improve their seismic performance by: (i) preventing the premature buckling of the stud members, and (ii) changing the dominant failure mode from brittle to ductile thanks to the bond-slip behaviour between OPLC and CFS studs. It is also shown that the design equations proposed by EC8 and ACI 318-14 standards overestimate the shear force capacity of OPLC-filled CFS shear wall systems by up to 80%. This shows it is necessary to propose methods with higher efficiency to predict the capacity of these systems for practical applications.

• Journal of the Korean Geographical Society
• /
• v.44 no.2
• /
• pp.176-186
• /
• 2009

Transportation policy to facilitate the public mode use is of the foremost importance to the local governments of Metropolitan Seoul, regarding the economic and environmental consequences of the increasing use of car. Understanding the travel behaviour is essential to the establishment of proper policy to guide more people to the use of public modes instead of private. The paper reports a result of sequential analysis of individual travel behaviour in Metropolitan Seoul, using a multi-dimensional motif search technique applied to Smart Card data that integrates individuals' different public mode uses. Groups of travel patterns with similar sequential information identified distinctive travel behaviour between Seoul north and south and between metro and bus uses. Travel patterns are more bounded within north Seoul and south Seoul respectively than crossing Han River between north and south. Within north and south, travel patterns visiting northern CBD and southern CBD, respectively, as well as their local neighbour in north and south, often use metro and metro-local bus combination, while travel patterns visiting only the north and south locals without CBDs more use only the local bus line and even only the areal bus line.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.430-432
• /
• 2005

Although color characteristics of IPS mode are much better than TN or VA mode, there still remains a room for improvement of the color characteristics of IPS mode compared with the conventional CRT. It has been generally as sumed that inherent color variation of IPS mode is entirely owing to dependence of the effective retardation on wavelength and role of optical axis of IPS mode has been little considered. In this study, we investigated the effects of driving voltages on the effective retardation and the effective optical axis by a computer simulation. The result shows that rotation of effective optical axis is dependent on wavelength and tends to be smaller for larger wavelength.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.11
• /
• pp.1829-1834
• /
• 2001

The aim of this study is to investigate the ductile fracture behavior under mixed mode (I/II) loading using SA533B pressure vessel steel. Anti-symmetric 4-point (AS4P) bonding tests were performed to obtain the J-R curves under two different mixed mode (I/II) loadings. In addition, the fractographic examination of fracture surfaces was carried out to compare with those of pure Mode I and Mode II. In conclusions, the J-R curves under Mixed Mode (I/II) loading were located between those of Mode I and Mode II loadings. When the mixture ratio of mixed mode (I/II) loading was high, the J-R currie of mixed mode (I/II) loading approached that of pure mode I loading after some amount of crack propagation. In contrast with the above fact, if the mixture ratio was low, the J-R curve looked after that of pure mode II loading. The fractographic evidences such as the shape of dimples under different loading conditions supported these conclusions.