• Journal of Korean Society of Steel Construction
• /
• v.9 no.3 s.32
• /
• pp.421-430
• /
• 1997

In this study, the static and the fatigue tests were performed with high tension bolted joints, of which the surfaces were spread with inorganic zinc-primer after shot-blast, and milling surface, and steel-natural surface, difference of friction surface condition were examined by comparing the esults of tests. From the result of synthetical investigation of this study. it is proper that using the torque management method in order to introduce design axial force to blots, and the provision of specifications that initial axial forces must be 110% of design axial forces is proper. Decreasing ratio of axial forces to initial force is proportional to common lorgarithms of time progress, it converge constant value after 20 hours, and decreasing ratio is little related to the roughness of friction surface. Sliding coefficient of milling, spreading inorganic zinc-primer, just producting is great in order and sliding forces are dependent on the applied axial forces, but if the applied axial forces are great, sliding coefficient become small by a loss of roughness. So it is confirmed that relation between the applied axial forces and the sliding forces are not proportional linearly. From the result of estimation on fatigue strength, all specimens satisfy the specifications with B-grade and milling surface is lower than the others about 14% in fatigue strength because in milling surface lose the function of friction-types joints at lower number of cycles. From the result of eximination for the distribution area of compressive force, friction area near to inside bolt is wider in the direction of stress than near to outside. It is guessed that this situation occurs because outside bolts firstly change from the friction connection to the bearing connection.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.9
• /
• pp.13-23
• /
• 2005

The prefabricated vertical drains (PVDs) are one of the most widely used techniques to accelerate the consolidation of soft clay deposits and dredged soil. Discharge capacity is one of the factors affecting the behavior of PVDs. In the field, a PVD is confined by clay or dredged soil, which is normally remolded during PVD installation. Under field conditions, soil particles may enter the PVD drainage channels, and the consolidation settlement of the improved subsoil may cause 131ding of the PVD. These factors will affect the discharge capacity of the PVDs. In this study an experimental study was carried out to estimate the discharge capacity of three different types of PVDs by utilizing the large-scale laboratory model testing and small-scale laboratory model testing equipments. The several factors such as confinement condition (confined by soft marine clay or dredged soil) and variations of the discharge capacity were studied with time under soil specimen confinement, The test results indicated that discharge capacity decreases with increasing load, time, and hydraulic gradient. With load application, the cross-sectional area of the drainage channel of PVD decreases because the filter of PVD is pressed into the core. The discharge capacity of the soft marine clay-confined PVDs is much lower than that of the dredged soil-confined PVDs.

• Geotechnical Engineering
• /
• v.13 no.5
• /
• pp.75-88
• /
• 1997

In this study an iterative procedure for the analysis of drilled shafts was proposed on the basis of the load transfer mechanism. Special attention was given to the estimation of bearing capacity of drilled shafts which was compared with driven piles, and then with the results of pile load test. The load displacement at the pile head was calculated by load than sfer curves (t -z curves, q-z curves) by using Vljayvergiya, Castelli and hi -linear models. Bab ed on the analytical results, it is found that the behavior of drilled shafts is different from that of driven piles the smaller the skin friction mobilized at the pile-boil interface, the smaller the development of the bearing capacity. Hence the greater pile head movement is required to mobilize the same mainitride of bearing capacity. This trend is more noticeable in sand than in clay. It is also found that as the length-todiameter ratios increase, the dirtference of ultimate bearing capacity between drilled shafts and driven piles is becoming lass ger in sand, but it is minor in clay.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.8
• /
• pp.531-538
• /
• 2015

This study examined the size and shape of the nano-silver particle through the analysis of electrical resistance when synthesizing nano-sized silver by using the chemical liquid reduction. Changes in particle behaviors formed according to the changes in electronic characteristics by electric resistance in each time period in the beginning of reduction reaction in a course of synthesizing the nano-silver particle formation were studied. In addition, analysis was conducted on particle behaviors according to the changes in concentration of $AgNO_3$ and in temperature at the time of reduction and nucleation and growth course when synthesizing the particles based on the particle behaviors were also examined. As the concentration of $AgNO_3$ increased, the same amount of resistance of approximately $5{\Omega}$ was increased in terms of initial electronic resistance. Furthermore, according to the result of formation of nuclear growth graph and estimation of slope based on estimated resistance, slops of $6.25{\times}10^{-3}$, $2.89{\times}10^{-3}$, and $1.85{\times}10^{-3}$ were derived from the concentrations of 0.01 M, 0.05 M, and 0.1 M, respectively. As the concentration of $AgNO_3$ increased, the more it was dominantly influenced by the nuclear growth areas in the initial phase of reduction leading to increase the size and cohesion of particles. At the time of reduction of nano-silver particle, the increases of initial resistance were $4{\Omega}$, $4.2{\Omega}$, $5{\Omega}$, and $5.3{\Omega}$, respectively as the temperature increased. As the temperature was increased into $23^{\circ}C$, $40^{\circ}C$, $60^{\circ}C$, and $80^{\circ}C$, slopes were formed as $4.54{\times}10^{-3}$, $4.65{\times}10^{-3}$, $5.13{\times}10^{-3}$, and $5.42{\times}10^{-3}$ respectively. As the temperature increased, the particles became minute due to the increase of nuclear growth area in the particle in initial period of reduction.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.5
• /
• pp.1025-1037
• /
• 2015

Flexible base isolation bearings that separate superstructure from ground have been widely used in the construction field because they make a significant contribution to increasing the fundamental period of the structure, thereby decreasing response acceleration transmitted into the superstructure. However, the established bearing devices installed to uphold the whole building give rise to some problems involved with failure and collapse due to lack of the capacity as modern structures are getting more massive and higher. Therefore, this study suggests new isolation bearings assembled with additional restrainers enabled to reinforcing and recentering, and then evaluates their performance to withstand the seismic load. The superelastic shape memory alloy (SMA) bars are installed into the conventional lead-rubber bearing (LRB) devices in order to provide recentering forces. These new systems are modeled as component spring models for the purpose of conducting nonlinear dynamic analyses with near fault ground motion data. The LRB devices with steel bars are also designed and analyzed to compare their responses with those of new systems. After numerical analyses, ultimate strength, maximum displacement, permanent deformation, and recentering ratio are compared to each model with an aim to investigate which base isolation models are superior. It can be shown that LRB models with superelastic SMA bars are superior to other models compared to each other in terms of seismic resistance and recentering effect.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1093-1098
• /
• 2013

A single-crystal sapphire is used as a transparent bulletproof window material; however, few studies have investigated the dynamic behavior and fracture properties under high-speed impact. High-speed and high-resolution sequential images are required to study the interaction of the bullet with the brittle ceramic materials. In this study, a device is developed to capture the sequence of high-speed impact/penetration phenomena. This system consists of a speed measurement device, a microprocessor-based camera controller, and multiple CCD cameras. By using a linear array sensor, the speed-measuring device can measure a small (diameter: up to 1 2 mm) and fast (speed: up to Mach 3) bullet. Once a bullet is launched, it passes through the speed measurement device where its time and speed is recorded, and then, the camera controller computes the exact time of arrival to the target during flight. Then, it sends the trigger signal to the cameras and flashes with a specific delay to capture the impact images sequentially. It is almost impossible to capture high-speed images without the estimation of the time of arrival. We were able to capture high-speed images using the new system with precise accuracy.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.2
• /
• pp.717-722
• /
• 2013

Background: Breast cancer is the most common cancer among women worldwide. The aim of this study was to investigate the relationship between tumor size and axillary lymph node involvement (ALNI) in patients with invasive lesions, to find the best candidates for a full axillary dissection. Additionally, we evaluated the association between tumor size and invasive behavior. The study was based on data from 789 patients with histopathologically proven invasive breast cancer diagnosed in Shohada University hospital in Tehran, Iran (1993-2009). Cinical and histopathological characteristics of tumors were collected. Patients were divided into 6 groups according to primary tumor size: group I ($0.1-{\leq}1cm$), II ($1.1-{\leq}2cm$), III ($2.1-{\leq}3cm$), IV ($3.1-{\leq}4cm$), V ($4.1-{\leq}5cm$) and VI (>5cm). The mean(${\pm}SD$) size of primary tumor at the time of diagnosis was $3.59{\pm}2.69$ cm that gradually declined during the course of study. There was a significant correlation between tumor size and ALNI (p<0.001). A significant positive correlation between primary tumor size and involvement of surrounding tissue was also found (p<0.001). The mean number of LNI in group VI was significantly higher than other groups (p<0.05). We observed more involvement of lymph nodes, blood vessels, skin and areola-nipple tissue with increase in tumor size. We found 15.3% overall incidence of ALNI in tumors ${\leq}2cm$, indicating the need for more investigation to omit full axillary lymph node dissection with an acceptable risk for tumors below this diameter. While in patients with tumors ${\geq}2cm$, 84.3% of them had nodal metastases, so the best management for this group would be a full ALND. Tumor size is a significant predictor of ALNM and involvement of surrounding tissue, so that an exact estimation of the size of primary tumor is necessary prior to surgery to make the best decision for management of patients with invasive breast cancer.

• Journal of Korean Academy of Nursing
• /
• v.31 no.2
• /
• pp.221-231
• /
• 2001

This study was conducted by analyzing all 33 articles based on the LISREL, published from January 1991 to March 1999 in Korea. The analyses consisted of the publication date of articles, principal dependent variables, subjects of the research, adequacy of sampling, adequacy of research purposes and results, accordance between theoretical model and hypothetical model, fit measures, theoretical base of model modification, and adequacy of conclusion. The results were as follows : . The thesis of 33 articles in total were outnumbered as 25 (75.8%) to 8 (24.2%) research articles. As for a sex classification of the subjects, 45.5% of the research were conducted around a female group of subjects, while 54.5% were done for both sex, The range of the sample size was 105 to 803, and the average was 259 subjects. . A single theoretical variable was measured for each measurement variable, any difference between variables was hardly found in 8 articles (24.2%), and 19 articles (57.6%) did not consider any measurement error. To analyze if the representative has been articles (21.2%) were seen with a sign of a representative. Questionnaires were used in a majority (31 articles) of the data collecting process. Only 2 articles (6.1%) were measured with a physiologic index simultaneously. . 14 articles (42.2%) were centered on theory development, 10 articles on theory synthesis, and 9 articles on theory test. The research purposes and results were consistent in 25 articles (75.5%) and 8 articles (24.2%) were inconsistent. The quality of life and health promotion behavior were the concepts most frequently studied as a dependent variable, and 7 articles centered on them. In applied theories a health promotion model was used on 4 articles (12.1%), while role theory and stress-coping models were in 3 articles respectively. . The articles were analyzed to see if the hypothetical model was elaborated and tested by the theoretical model. Twenty-five articles proved to be rationale for the inconsistencies. Also, 56.5% proposed hypotheses were supported among the subject articles, and 30 articles (90.0%) suggested a revised model. Path coefficient (17 articles) and theoretical adequacy (17 articles) were the standards mostly used. In conclusion, the principal factors were obtained from the research are to be considered as the principes of LISREL application. First, a model has to be established on a theoretical base rather than empirical results dependent on the data. The results are also required to be globally interpreted. Secondly, at least 200 samples are necessary to satisfy the need. Third, more than 3 measurement variables are to be adjusted to a single theoretical variable; the measurement errors must be suggested as well. Finally, normal distribution characteristics of the data and the estimation method need to be reported. Based on the research result, the follows are suggested; . Systematic criteria on the LISREL application and procedure need to be developed . Agreement form is required to report the results of research using the LISREL

• Environmental and Resource Economics Review
• /
• v.13 no.3
• /
• pp.337-366
• /
• 2004

Contingent Valuation Method (CVM), as non-market valuation approach, has been criticized on that respondents may not realistically reflect their budget constraints in answering willingness to pay (WTP) for hypothetical CV questions. This paper empirically estimates the income calibration factor associated with CV responses through combining travel cost method and contingent valuation method in a utility-theoretic framework. The joint model of recreation demand function and contingent WTP function was applied to an important case study on the Man Kyoung River system, whose water quality is at issue because of the Sae Alan Kum reclamation project. Relevant economic variables such as price, income and water quality had significant influence as anticipated by the economic theory. Equally important, the income calibration factor was not significantly different from one, suggesting that the systematic discrepancies of CV responses relative to the actual behavior was not detected at least in terms of budget exaggeration. Overall, this study supports the notion that carefully designed CVM studies can provide informative data on individuals' willingness to pay for environmental quality changes.

• Environmental Analysis Health and Toxicology
• /
• v.25 no.4
• /
• pp.307-314
• /
• 2010

Objectives : Arsenic (As) is ubiquitously distributed in the environment and has been known as a human carcinogen. The main source of arsenic exposure in general population is an oral route through As-contaminated water and foods. This study was performed to estimate the daily intake of As from diet and associated factors in Korean adults. Methods : We investigated 590 adults, 249 males and 341 females, with age of 20 years and older, who had not been exposed to the As occupationally. Study subjects were interviewed for demographic characteristics, lifestyles and diets during the last 24 hours. The estimation of As intake daily was based on amount of food consumption and As concentration in each food by using database of As concentrations in 117 food species. Results : Daily As intake was estimated as $56.46\;{\mu}g$/day, $56.60\;{\mu}g$/day in male and $56.36\;{\mu}g$/day in female. As intake was not significant from sex, age group, smoking and alcoholic habits, while was by occupation with the most intake of As in fishery. The daily As intakes was positively correlated with the total food consumption, specifically related with fishes and shellfishes, seaweeds, oils, grains and flavors. About 75% of As intake from diet was contributed by seafoods, such as $32.07\;{\mu}g$/day from fishes & shellfishes and $10.05\;{\mu}g$/day from seaweeds. However, it is necessary to evaluate if the dietary As intake affects on the levels of As in the body. Conclusions : The amount of As intake daily in Korean adults was estimated as $56.46\;{\mu}g$/day, and is determined mainly by diet behavior. The seafoods, such as fishes & shellfishes and seaweeds, is major source of As exposure from diet in Korean.