• 마이크로전자및패키징학회지
• /
• 제8권2호
• /
• pp.25-29
• /
• 2001

본 연구에서는 mesocarbon microbeads(MCMB)카본에 에폭시 수지(resin)를 코팅시킴으로 서 카본전극 표면개질에 따른 전지 성능의 개선효과에 관하여 고찰하였다. 에폭시 수지에 의한 카본의 표면코팅은 MCMB 분말을 에폭시 수지가 용해된 THF(tetrahydrofuran)용액에 넣어 혼합함으로서 표면에 에폭시 수지가 코팅 되도록 하였다. 이렇게 에폭시 수지가 코팅된 MCMB를 $1000^{\circ}C$이상의 온도로 열처리하여 고분해능 투과전자현미경으로 관찰한 결과, 코팅층은 비정질 카본 구조를 지님을 알 수 있었다. 또한, 에폭시 수지에 의하여 코팅된 MCMB는 코팅되지 않은 MCMB보다 더 높은 BET비 표면적을 나타내었으며, 더 우수한 충방전 용량과 싸이클 특성을 나타내었다. 카본표면에 코팅된 에폭시 수지가 얇은 비정질 막으로 표면에 존재함으로서 전해질과 카본결정과의 반응을 억제시키는 방지막 역할을 하기 때문에 전지특성이 개선된 것으로 해석된다.

• 자원리싸이클링
• /
• 제19권6호
• /
• pp.51-60
• /
• 2010

리튬이차전지 양극스크랩으로부터 코발트와 리튬을 회수하기위해 물리적 전처리, 침출, 용매추출 및 회수실험을 행하였다. 실험재료로 제조공정에서 발생되는 코발트계 양극스크랩을 사용하여 단위공정별 최적조건을 구하였다. 물리적전처리 최적조건은 온도 $500{\sim}550^{\circ}C$, 파쇄날 회전속도 1000rpm이었으며, 침출 최적조건은 300rpm, 2M $H_2SO_4$, 2.5M $H_2O_2$, $95^{\circ}C$이었다. D2EHPA(bis(2-ethylhexyl) phosphoric acid) 와 PC88A를 각각 알루미늄과 코발트의 추출제로 사용하여 분리.정제하였으며, 코발트는 염기성시약을 사용하여 $Co(OH)_2$로, 리튬은 탄산나트륨 및 LiOH를 사용하여 탄산리튬($LiCO_3$)으로 회수하였다. $Co(OH)_2$는 열처리를 하여 삼산화코발트($Co_3O_4$)로 만들고 분쇄기를 사용하여 10 ${\mu}m$정도의 입자를 만들었다. 최적조건에서 코발트와 리튬 회수율은 99%이상, 리튬회수율은 99%이상이었으며, 삼산화코발트의 순도는 99.98%이상이었다.

• 자원리싸이클링
• /
• 제10권6호
• /
• pp.9-14
• /
• 2001

폐리튬이온전지의 재활용 일환으로 양극활물질인 $LiCoO_2$로부터 Co와 Li을 회수하기 위하여 황산침출거동을 조사하였다. 황산 2M용액, $75^{\circ}C$ 조건에서 환원제를 첨가하지 않은 경우, $LiCoO_2$로부터 Li가 거의 100% 침출되는 반면에 Co는 같은 조건에서 40% 이하의 침출율을 보였다. Co의 침출율을 향상시키기 위하여 과산화수소를 환원제로 2~20 vol%범위에서 사용하였다 10 vol% 이상의 과산화수소를 첨가하였을 때, Co와 L거 침출율은 모두 95% 이상 이었다. 이는 환원제로서 과산화수소가 Co(III)를 Co(II)로 환원시켜 침출이 용이해졌기 때문으로 생각된다. 황산농도, 온도, 과산화수소 첨가량이 증가함에 따라 Co와 L리 침출율은 증가한 반면에 초기 광액농도가 증가할수록 Co와 L긴 침출율은 감소하였다. 이상의 조업변수 실험을 통하여 코발트계 리튬이온전지의 양극활물질인 $LiCoO_2$의 황산침출에서 황산농도 2 M, 침출온도 $75^{\circ}C$,초기광액농도 100 g/L, 과산화수소 첨가량 20 vol%에서 30분의반응시간이 침출 최적조건으로 생각된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 하계학술대회 논문집
• /
• pp.393-396
• /
• 1991

The load factor is continuously decreasing with the increase of the daytime power demand so that the load levelling is required. Since the pumped storage power plant for the load levelling has some problems, new storage techniques such as the battery energy storage system (BESS) had been developed in the early 1980s. The MW BESS had been already interconnected to power system in the developed countries, while the 20KW BESS was developed and is being operated by KERI and KEPCO in our country, the development project of MW BESS is being persued now. Then, it is important to evaluate the economics and prospect of BESS. This paper presents the economic target and introduction prospect of BESS in korea.

• Bulletin of the Korean Chemical Society
• /
• 제35권5호
• /
• pp.1516-1522
• /
• 2014

A series of 20 wt % $(NH_4)_2SO_4$ and 3 wt % $Al_2O_3$ surface treatments were applied to $Li[Li_{0.2}Mn_{0.54}Co_{0.13}Ni_{0.13}]O_2$ substrates. The $Li[Li_{0.2}Mn_{0.54}Co_{0.13}Ni_{0.13}]O_2$ substrates were synthesized using a co-precipitation method. Sample (a) was left pristine and variations of the 20 wt % $(NH_4)_2SO_4$ and 3 wt % $Al_2O_3$ were applied to samples (b), (c) and (d). XRD was used to verify the space group of the samples as R$\bar{3}$m. Additional morphology and particle size data were obtained using SEM imagery. The $Al_2O_3$ coating layers of sample (b) and (d) were confirmed by TEM images and EDS mapping of the SEM images. 2032-type coin cells were fabricated in a glove box in order to investigate their electrochemical properties. The cells were charged and discharged at room temperature ($25^{\circ}C$) between 2.0V and 4.8V during the first cycle. The cells were then charged and discharged between 2.0V and 4.6V in subsequent cycles. Sample (d) exhibited lower irreversible capacity loss (ICL) in the first charge-discharge cycle as compared to sample (c). Sample (d) also had a higher discharge capacity of ~250 mAh/g during the first and second charge-discharge cycles when compared with sample (c). The rate capability of the $Al_2O_3$-coated sample (b) and (d) was lower when compared with sample (a) and (c). Sample (d), coated with $Al_2O_3$ after the surface treatment with $(NH_4)_2SO_4$, showed an improvement in cycle performance as well as an enhancement of discharge capacity. The thermal stability of sample (d) was higher than that of the sample (c) as the result of DSC.

• 한국수소및신에너지학회논문집
• /
• 제10권3호
• /
• pp.185-189
• /
• 1999

Effects of alloy modification with the $Zr_{0.6}Ti_{0.4}V_{0.4}Ni_{1.2}Mn_{0.4}$ alloy for an electrode use have been investigated. For the alloy composition, a part of Mn was substituted by Co, Cr and Fe. The experimental results showed that Co accelerated activation of alloy, and Fe and Cr improved the discharge capacity. These results agree with P-C-T curves of each alloy. But substituting Fe for Mn showed the decrease of the discharge capacity when discharged at high rate (60mA, about 1C rate). Considering both the discharge capacity and the high rate discharge property, $Zr_{0.6}Ti_{0.4}V_{0.4}Ni_{1.2}Mn_{0.3}Cr_{0.1}$ alloy was found to be the best alloy among the alloys subjected to the test.

• 센서학회지
• /
• 제14권6호
• /
• pp.415-422
• /
• 2005

Using stretch sensors, a stuttering treatment training device that improve the abnormal breathing of stutterer was designed and developed. To improve stutterer's inadequate breathing method that is one of principal reason of stammering, the device estimates breathing method by checking the changes of the stretch sensor's resistances those are put on the chest and abdomen of user. And a vocal exercise program that carry out exercises only when the user maintains the abdominal breathing was designed. Using a PIC16C711 device that includes an A/D convertor, a main controller was designed and the vocal exercises software was developed using Director and C program with graphic user interface for user convenience. The controller sends the resistance data of sensors to PC through the serial port and the software verifies the breathing method. And the device was designed that the RTS (request to send) pin of serial port in PC is used as a power source so that it can work without any battery or other power source. Three stutterers have carried out the clinical experiments using the implemented device for two months and the results showed it was excellent to alleviate the stuttering.

• 한국세라믹학회지
• /
• 제40권1호
• /
• pp.69-76
• /
• 2003

리튬이차 박막전지로서, 실리콘 첨가(0, 2, 6, 10, 20㏖%)에 따른 주석 산화물 박막을 기판온도 30$0^{\circ}C$, Ar:O$_2$=7:3으로 R.F. magnetron sputtering법으로 제조하였다. 실리콘의 함량이 증가함에 따라, Si-O 결합량이 증가하고 Sn-O 결합량은 감소하였다. 적정량의 실리콘 첨가는 주석의 산화상태를 감소시켜 비가역성을 줄이고 충방전 동안 주석의 부피변화를 막아 사이클 특성이 향상되는 결과를 보여주었다. 6㏖% Si를 첨가한 주석 산화물 박막은 100사이클동안 700mAh/g의 용량을 가지는 가장 좋은 사이클 특성을 나타내었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1682-1684
• /
• 1996

Recently, because diffusion of cordless machine and smart card and so on, and concern of unpolluted materials, one are concerned with Li secondary batteries. Li secondary batteries have high voltage, high energy density and high power density, and heavy metal pollution problems are little. Mn is low price and is distributed much quantity. Therefore, we investigated $MnO_2$. In this study, we worked the electrochemical properties and charge/discharge characteristics of $MnO_2/Li$ cells. In results, the more heating temperature is high, the more ${\gamma}-phase$ varied ${\beta}-phase$, and when $MnO_2$ is heated at $320^{\circ}C$ and super-s-black 20wt% is mixed, characteristics are the best.

• 한국분말재료학회지
• /
• 제22권4호
• /
• pp.240-246
• /
• 2015

Anodic aluminum oxide (AAO) has been widely used for the development and fabrication of nano-powder with various morphologies such as particle, wire, rod, and tube. So far, many researchers have reported about shape control and fabrication of AAO films. However, they have reported on the shape control with different diameter and length of anodic aluminum oxide mainly. We present a combined mild-hard (or hard-mild) anodization to prepare shape-controlled AAO films. Two main parameters which are combination mild-hard (or hard-mild) anodization and run-time of voltage control are applied in this work. The voltages of mild and hard anodization are respectively 40 and 80 V. Anodization was conducted on the aluminum sheet in 0.3 mole oxalic acid at $4^{\circ}C$. AAO films with morphologies of varying interpore distance, branch-shaped pore, diameter-modulated pore and long funnel-shaped pore were fabricated. Those shapes will be able to apply to fabricate novel nano-materials with potential application which is especially a support to prevent volume expansion of inserted active materials, such as metal silicon or tin powder, in lithium ion battery. The silicon powder electrode using an AAO as a support shows outstanding cycle performance as 1003 mAh/g up to 200 cycles.