• Proceedings of the KIEE Conference
• /
• 2008.04b
• /
• pp.123-124
• /
• 2008

Battery is one of the emergency power. Battery reliability is a very important to keep up the minimum of building capabilities in case of interruption of electric power. Instantaneous discharge test is carried out for measuring transient voltage change(${\Delta}V$) and internal instantaneous impedance(Z), and then it is compared with discharge test results for the estimating the battery capacity. As a result, it was confirmed that the voltage change(${\Delta}V$) and the instantaneous impedance of the batteries failed in actual discharge test were higher that those of the sound batteries. Such an instantaneous discharge test can be a diagnosis of battery sound.

• Proceedings of the KIEE Conference
• /
• 2004.05a
• /
• pp.150-152
• /
• 2004

The battery charge/discharge process, the final step of the secondary battery production process, requires real-time precision controls for improving both lifetime and performance of the battery cell. In this paper, we present embedded system design for precision control of the secondary battery charge/discharge production process using low power embedded processor based on embedded linux. This system receive charge/discharge command from the main server through ethernet. Compared to existing charge/discharge control system, our design makes low cost and precision control system possible.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.156-158
• /
• 2018

The inconsistencies between paralleled battery cells are becoming more considerable issue in high capacity battery applications like electric vehicles. Due to differences in state-of-charge (SOC) and internal resistance within individual cells in parallel, charging or discharging current is not appropriately balanced to each cell in terms of SOC, which may shorten the lifetime or sometimes cause safety issues. In this paper, an intelligent cell-balancing algorithm is proposed to overcome the inconsistency issue especially for paralleled battery cells. In this scheme, SOC information collected in the sub-BMS module is sent to the main-BMS module, where the number of parallel cells to be connected to DC bus is continuously updated based on the suggested SOC comparison rule. To verify the method, operation of the algorithm on 4 paralleled battery cells are simulated on Matlab/Simulink. The simulation result shows that the SOCs of paralleled cells are evenly redistributed. It is expected that the proposed algorithm provides high reliable and prolong the life cycle and working capacity of the battery pack.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.8 no.6
• /
• pp.339-345
• /
• 2013

This paper addresses the system lifetime maximization algorithm in multi-hop sensor network system. A multi-hop sensor network consists of many battery-driven sensor nodes that collaborate with each other to gather, process, and communicate information using wireless communications. As sensor-driven applications become increasingly integrated into our lives, we propose a energy-aware scheme where each sensor node transmits informative data with adaptive data rate to minimize system energy consumption. We show the optimal data rate to maximize the system lifetime in terms of remaining system energy. Furthermore, the proposed algorithm experimentally shows longer system lifetime in comparison with greedy algorithm.

• Journal of Korea Multimedia Society
• /
• v.21 no.5
• /
• pp.592-598
• /
• 2018

In wireless sensor networks where there is no centralized base station, each node has limited transmission range and the multi-hop routing for transmitting data to the destination is the one of the important technical issues. In particular, the wireless sensor network is not powered by external power source but operates by its own battery, so it is required to maximize the network life through efficient use of energy. To balance the power consumption, the residual power based adaptive power control is required in routing protocol. In this paper, we propose a routing protocol that prolongs the network lifetime by balancing the power consumption among the nodes by controlling the transmit power according to the residual power. We evaluate the proposed routing protocol using extensive simulation, and the results show that the proposed routing scheme can balance the power consumption and prolong network lifetime.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.7
• /
• pp.1273-1278
• /
• 2008

In community computing environments, various members cooperate with each other systematically for attaining each community's goals. Because community computing environments are organized on the basis of PAN (Personal Area Network), each member commonly uses the power of batteries. If one member in community uses up the power of battery and does not operate normally, the community will not be able to provide the ultimate service goals for its users and be terminated finally. Therefore, it is necessary for accurate community operation to prevent a specific member's lifetime from terminating, as checking each member's power consumption in real-time. In this paper, we propose WEL (WEighted Leach) algorithm for optimizing lifetime of the members in community.

• The KIPS Transactions:PartC
• /
• v.15C no.4
• /
• pp.303-310
• /
• 2008

To increase the lifetime of ad-hoc networks, a ratio of energy consumption for each node should be kept constant by equally distributing network traffic loads into all of the nodes. In this paper, we propose a modified AODV routing protocol to determine a possible route by considering a remaining battery capacity of a node and the degree of its usage. In addition, to reduce the amount of energy consumption during the path rediscovery process due to the huge amount of the AODV control messages the limited number of possible routes are stored into a routing table of a source node. When some links of a route fail, another possible path can be looked up in the table before the route discovery process should be initiated. We have tested our proposed method with a conventional AODV and a MMBCR method which is one of the power-efficient energy routing protocols based on the three performance metrics, i.e., the total remaining battery capacity, network lifetime and the ratio of data packets received by the destination node to compare their performance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.3
• /
• pp.227-233
• /
• 2011

This paper proposes a design and experiment of three phase interleaved dc-dc converter for 5kW battery charger. The charger consists of a three-phase interleaved dc-dc converter, which interfaces batteries and DC link, and a grid connected inverter. Lead-acid battery is modeled in a simple R-C model by matlab. Parameters of the battery are estimated based on step current discharging test. The battery is connected to three-phase interleaved DC-DC converter in order to reduce the ripple current to the battery and so, increase the lifetime of battery. Controller for charging and discharging mode is designed and tested in a 5kW charger prototype.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.9 no.2
• /
• pp.75-80
• /
• 2014

Energy consumption of sensor nodes is minimized because it has limited energy generator in wireless sensor network. Electronic shelf label system is one of application fields using wireless sensor networks. Battery size of small apparatus for displaying price is restricted. Therefore its current consumption have to be minimized. Furthermore the method for minimization of peak current would be considered because life cycle of coin battery used to display or RF is vulnerable to intensity of drain current. In this paper, we analyze current consumption pattern of low-power electronic shelf label system. Then we propose the method for minimization of current consumption by modification of software and hardware. Current consumption of the system using proposed method are approximately 15 to 20 percent lower than existing system and the life cycle of the system is approximately 10 percent higher than existing system.

• Electronics and Telecommunications Trends
• /
• v.32 no.6
• /
• pp.40-47
• /
• 2017

One of the main technical constraints of a conventional battery is the limited lifetime of electric energy supplied. With self-power generation using an internal radioisotope as an emitter of beta particles, and a PN-junction semiconductor as an absorber of the beta particles, a betavoltaic battery can provide electric energy to electric devices in a semi-permanent manner. Hence, a betavoltaic battery can be adopted as the solution to the power source issue of IoT devices placed in locations that people cannot easily access, such as in the deep sea, a desert, and space, and requiring a long operation time without an electrical charging. This paper covers the current trends in betavoltaic batteries including issues regarding their technology, application, and patents.