• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -2
• /
• pp.932-935
• /
• 2002

In this paper, we introduce new FTL(Flash Translation Layer) driver algorithm that tolerate the power off errors. FTL driver is the software that provide the block device interface to the upper layer software such as file systems or application programs that using the flash memory as a block device interfaced storage. Usually, the flash memory is used as the storage devices of the mobile system due to its low power consumption and small form factor. In mobile system, the state of the power supplement is not stable, because it using the small sized battery that has limited capacity. So, a sudden power off failure can be occurred when we read or write the data on the flash memory. During the write operation, power off failure may introduce the incomplete write operation. Incomplete write operation denotes the inconsistency of the data in flash memory. To provide the stable storage facility with flash memory in mobile system, FTL should provide the fault tolerance against the power off failure. SSR (Simple Sector Remapper) is a fault tolerant FTL driver that provides block device interface and also provides tolerance against power off errors.

• 한국산학기술학회논문지
• /
• 제12권1호
• /
• pp.371-374
• /
• 2011

본 논문에서는 LED를 조명의 전원으로 사용하는 소규모 태양광 발전시스템의 설계용 소프트웨어 개발에 대해 제안한다. 태양광 발전시스템의 최적 설계를 위해서, 태양광 모듈과 배터리 용량 산정시, LED 부하의 운전 전력소비량이 고려될 수 있게 하였다. 태양광 발전시스템을 설계하는 엔지니어의 사용 편의성을 높이기 위해, 소프트웨어는 그래픽 사용자 인터페이스와 모니터링 기능을 제공하여, 시스템 설계 후 설치 단계에서 전체 시스템의 운전 상태를 쉽게 파악할 수 있도록 하였다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.1449-1454
• /
• 2004

For the research, we developed the hardware and software of the measurement system for on-line test and evaluation. The software controls the hardware of the measurement data and acts as a interface between users and the system hardware. In this paper, we studied performances of the auxiliary block for high-speed railway vehicle. In order to performance these works, the conversion system was developed. Using this system, we obtained the important results, such as voltage values for the battery charger and auxiliary block. Also, we diagnosed the faults and performed the evaluation for auxiliary block using the measurement system and data.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.435-437
• /
• 2003

Recently, as the road capacity reaches the limit and environmental problems becomes serious, there is gradually increased a need for railroad vehicles that are environment-friendly and have time regularity, reliability and safety. Accordingly, in addition to conventional railroad vehicles, lots of vehicles are being newly developed. We developed the hardware and software of the measurement system for on-line test and evaluation of korean hish speed train. The software controls the hardware of the measurement data and acts as interface between users and the system hardware. In this paper, we is studied for electric apparatus performance of railway vehicle using sensor. In order to this test is developed signal conversion system. Using this system, we obtained important result for pantograph voltage, battery voltage, axle speed, and running speed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.1294-1296
• /
• 2003

For this research, we developed the hardware and software of the measurement system for on-line test and evaluation. The software controls the hardware of the mesurement data and acts as interface between users and the system hardware. In this paper, we is studied for Aux. Block performance of railway vehicle. In order to this test is developed signal conversion system. Using this system. we obtained important result for battery voltage, Aux. Block temperature.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.408-417
• /
• 2011

The plug-in hybrid electric vehicles (PHEVs) are specialized hybrid electric vehicles that have the potential to obtain enough energy for average daily commuting from batteries. The PHEV battery would be recharged from the power grid at home or at work and would thus allow for a reduction in the overall fuel consumption. This paper proposes an integrated power electronics interface for PHEVs, which consists of a novel Eight-Switch Inverter (ESI) and an interleaved DC/DC converter, in order to reduce the cost, the mass and the size of the power electronics unit (PEU) with high performance at any operating mode. In the proposed configuration, a novel Eight-Switch Inverter (ESI) is able to function as a bidirectional single-phase AC/DC battery charger/ vehicle to grid (V2G) and to transfer electrical energy between the DC-link (connected to the battery) and the electric traction system as DC/AC inverter. In addition, a bidirectional-interleaved DC/DC converter with dual-loop controller is proposed for interfacing the ESI to a low-voltage battery pack in order to minimize the ripple of the battery current and to improve the efficiency of the DC system with lower inductor size. To validate the performance of the proposed configuration, the indirect field-oriented control (IFOC) based on particle swarm optimization (PSO) is proposed to optimize the efficiency of the AC drive system in PHEVs. The maximum efficiency of the motor is obtained by the evaluation of optimal rotor flux at any operating point, where the PSO is applied to evaluate the optimal flux. Moreover, an improved AC/DC controller based Proportional-Resonant Control (PRC) is proposed in order to reduce the THD of the input current in charger/V2G modes. The proposed configuration is analyzed and its performance is validated using simulated results obtained in MATLAB/ SIMULINK. Furthermore, it is experimentally validated with results obtained from the prototypes that have been developed and built in the laboratory based on TMS320F2808 DSP.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.507-510
• /
• 2002

We developed a human-sized BWR(biped walking robot) named KUBIRI driven by a new actuator based on the ball screw which has high strength and high gear ratio. KUBIRI was developed to walk autonomously such that it is actuated by small torque motors and is boarded with DC battery and controllers. To utilize informations on the human walking motion and to analyze the walking mode of robot, a motion capture system was developed. The system is composed of the mechanical and electronic devices to obtain the joint angle data. By using the obtained data, a 3-D graphic interfacer was developed based on the open inventor tool. Through the graphic interfacer, the control input of KUBIRI is performed.

• 한국산학기술학회논문지
• /
• 제12권2호
• /
• pp.920-926
• /
• 2011

본 논문에서는 신재생에너지 활용을 위한 다중 추적식 태양광 발전 감성형 LED 가로등을 제안한다. 제안하는 가로등 시스템은 다중 추적방식의 태양광 추적기능을 갖추고 있고 감성형 고품위 LED 램프와 제어회로를 사용하여 센서를 통해 입력되는 온도 및 습도를 기반으로 최대의 일조량을 받을 수 있도록 하였다. 신재생에너지 활용의 핵심 요소인 효율적인 축전지 활용을 위해 충방전 컨트롤러를 개발하였고 원격모니터링 기능 및 제어기능도 구현 하였다. 제안하는 가로등 시스템은 기존 기술에 비하여 추적 동작이 우수하고 에너지효율이 향상되었으며 기존에 개발되지 않았던 추적식 태양광 발전 시스템과 감성형 LED를 결합함으로써 차세대 가로등 시스템의 모델로서의 활용될 수 있게 하였다.

• 전기학회논문지P
• /
• 제64권2호
• /
• pp.57-61
• /
• 2015

Current research and development efforts and other projects for energy storage systems (ESS) have recently been gaining attention. This is due to the many applications where ESS, particularly batteries, can be used. Among these are peak shaving, frequency regulation, and stabilization of renewable energy output. KEPCO has completed the construction and demonstration of a 4-MW battery energy storage system (BESS) located in Jeju City to verify its practicability in the power grid. KEPCO Research Institute has also been developing technology for the commercialization of BESS, and has been conducting a trial run of a 52-MW ESS (28MW + 24MW of Seo-Anseong and Shin-Yongin substations) constructed in 2014 for frequency regulation. This paper discusses the development of operation methods, as well as an operation user interface, for the safe operation and monitoring of BESS used for frequency regulation in a power system. Included are operation and simulation methods for various normal and transient frequency situations that can be experienced by a power system. Also discussed are the results obtained after applying these methods to the 4-MW BESS and the 52-MW ESS, both used for frequency regulation. The technology in this paper will be applied to 500MW ESS for frequency regulation of KEPCO by 2017. It is expected that this technology helps a safe and reliable operation and control of ESS for frequency regulation through its continuous upgrade.

• 인터넷정보학회논문지
• /
• 제16권5호
• /
• pp.29-38
• /
• 2015

에너지 저장장치(Energy Storage System)은 전력 수요가 적을 때 전력을 저장해 두었다가 수요가 발생하거나 비상시 저장된 전력을 사용함으로 전기 에너지를 저장하여 필요할 때 사용 가능함으로써 에너지 이용 효율 향상, 전력공급 시스템 안정화 및 신재생 에너지 활용도 향상 효과를 가지는 시스템이다. 최근 세계적으로 에너지의 효율적인 소비에 대한 관심이 증대되면서 전력의 안정적인 공급을 원하는 수요자와 전력 수요 평준화를 원하는 공급자의 요구를 충족시켜줄 수 있는 에너지 저장장치의 필요성이 증대되고 있다. 현재 에너지 저장장치를 구성하는 Power Conditioning System(PCS), Battery Management System(BMS), 배터리 셀은 제조사별로 상이한 규격을 가진다. 이로 인해 각 핵심 부품 간 인터페이스가 규격화되어 있지 않아, 에너지 저장장치의 구성 및 운영에 난점으로 작용하고 있다. 본 논문에서는 제조사별로 상이한 특징을 가지는 부품들의 설정과 효율적 운영에 필요한 정보를 수용하여 에너지 저장장치를 구성할 수 있는 XML 기반의 에너지 시스템 전용 프로파일 시스템의 설계와 분석방안을 제안한다. 제조사별 PCS, BMS, 배터리 셀과 그 외의 주변 기기들의 설정 정보 및 운영 정보를 분석하여 프로파일 규격을 정의하고, 에너지 저장장치에 적용할 수 있는 프로파일 어댑터 소프트웨어를 설계 및 구현한다. 프로파일 어댑터를 통해 생성된 프로파일은 설정 프로파일과 운영 프로파일로 구성되며, 추후 확장성을 고려하여 표준 XML의 규격을 따른다. 구현된 프로파일 시스템의 검증은 에너지 저장장치 시스템에 적용되어 기본적인 충 방전 동작을 통해 정상 동작 결과를 제안한다.