• Journal of the Korean Electrochemical Society
• /
• v.21 no.4
• /
• pp.80-87
• /
• 2018

Safety issues in Li-ion battery system have been prime concerns, as demands for power supply device applicable to wearable device, electrical vehicles and energy storage system have increased. To solve safety problems, promising strategy is to replace organic liquid electrolyte with non-flammable solid electrolyte, leading to the development of all-solid-state battery. However, relative low conductivity and high resistance from rigid solid-solid interface hinder a wide application of solid electrolyte. Composite electrolytes composed of organic and inorganic parts could be alternative solution, which in turn bring about the increase of conductivity and conformal contact at physically rough interfaces. In our study, composite electrolytes were prepared by combining poly(ethylene oxide)(PEO) and $Li_7La_3Zr_2O_{12}$ (LLZO). The crystallinity, morphology and electrochemical performances were investigated with the control of LLZO contents from 0 wt% to 50 wt%. From the results, it is concluded that optimum content and uniform dispersion of LLZO in polymer matrix are significant to improve overall conductivity of composite electrolyte.

• Membrane Journal
• /
• v.31 no.5
• /
• pp.351-362
• /
• 2021

All-vanadium redox flow battery (VRFB) is one of the promising high-capacity energy storage technologies. The ion-exchange membrane (IEM) is a key component influencing the charge-discharge performance and durability of VRFB. In this study, a pore-filled anion-exchange membrane (PFAEM) was fabricated by filling the pores of porous polytetrafluoroethylene (PTFE) support with excellent physical and chemical stability to compensate for the shortcomings of the existing hydrocarbon-based IEMs. The use of a thin porous PTFE support significantly lowered the electrical resistance, and the use of the PTFE support and the introduction of a fluorine moiety into the filling ionomer significantly improved the oxidation stability of the membrane. As a result of the evaluation of the charge-discharge performance, the higher the current efficiency was seen by increasing the fluorine content in the PFAEM, and the superior voltage and energy efficiencies were shown owing to the lower electrical resistance compared to the commercial membrane. In addition, it was confirmed that the use of a hydrophobic PTFE support is more preferable in terms of oxidation stability and charge-discharge performance.

• Applied Chemistry for Engineering
• /
• v.32 no.3
• /
• pp.290-298
• /
• 2021

A purification process was performed for the application of natural graphite as an anode material. The influence of the structural change and impurity content of graphite according to the process on the anode electrochemical characteristics was investigated. Natural graphite was chemically/physically purified by acid-treatment which used different amounts of solution of ammonium fluoride/sulfuric acid in the same ratio and thermal treatment used different temperatures (800~2500 ℃). Acid-treatment had limitation to remove impurities, and identified that all impurity contents was removed except some traces of atom such as Si by after progressed thermal-treatment until 2500 ℃. The anode materials characteristic of graphite treated by purification process was improved, and changes in the structure and impurity contents affected dominantly the capacity, rate property and initial Coulombic efficiency. Consequently, the complex purification process improved the graphite structure and also the performance of lithium ion battery by controlling the excessive formation of solid electrolyte interphase and expanding Li⁺ insertion space originated from the effective removal of impurities.

• Journal of Korea Society of Industrial Information Systems
• /
• v.27 no.2
• /
• pp.71-82
• /
• 2022

In order to replace the sampling tensile test of products produced in the tab welding process, which is one of the automotive battery manufacturing processes, vision inspectors are currently being developed and used. However, the vision inspection has the problem of inspection position error and the cost of improving it. In order to solve these problems, there are recent cases of applying deep learning technology. As one such case, this paper tries to examine the usefulness of applying Faster R-CNN, one of the deep learning technologies, to existing product inspection. The images acquired through the existing vision inspection machine are used as training data and trained using the Faster R-CNN ResNet101 V1 1024x1024 model. The results of the conventional vision test and Faster R-CNN test are compared and analyzed based on the test standards of 0% non-detection and 10% over-detection. The non-detection rate is 34.5% in the conventional vision test and 0% in the Faster R-CNN test. The over-detection rate is 100% in the conventional vision test and 6.9% in Faster R-CNN. From these results, it is confirmed that deep learning technology is very useful for detecting welding error of lead tabs in automobile batteries.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2014.06a
• /
• pp.157-159
• /
• 2014

In this paper, we introduce SlimSRP, an ultra-low-power digital signal processor (DSP) solution for mobile audio and voice applications. So far, application processors (APs) have taken charge of all the tasks in mobile devices. However, they have suffered from short battery life problems to deal with complex usage scenarios, such as always-on voice trigger with continuous audio playback. From extensive analysis of audio and voice application characteristics, SlimSRP is designed to relive the performance and power burden of APs. It employs three-issue VLIW architecture, and the major low-power and high-performance techniques include: (1) an optimized register-file architecture friendly for constants generation, (2) a powerful instruction set to reduce the number of register file accesses and (3) a unique instruction compression scheme that contributes to saved memory size and reduced cache miss. An implementation of SlimSRP runs at up to 200MHz and the logic occupies 95K NAND2 gates in Samsung 28LPP process. The experimental results demonstrate that a MP3 decoder application with a 128kbps 44.1kHz input can run at 5.1MHz and the logic consumes only 22uW/MHz.

• KIPS Transactions on Computer and Communication Systems
• /
• v.2 no.5
• /
• pp.203-208
• /
• 2013

As smartphones are rapidly and widely spread, their applications request gradually larger computation power. Recently, in the personal computer, computing power of hardware has exceeded performance requirement of software sometimes. Computing power of smartphone, however, will not grow at the same pace as demand of applications because of form factor to seek thinner devices and power limitation by relatively slow technical progress of battery. Computation offloading is getting huge attention as one of solution for the problem. It has not commonly used technology in spite of advantages for performance and power consumption since the existing offloading frameworks are difficult for application developer to utilize. This paper presents an application developer-friendly offloading framework, named SorMob. Based on Aspect Oriented Programming model, SorMob provides a convenient environment for application development, and its performance was verified by comparing with the existing offloading framework.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.1
• /
• pp.89-97
• /
• 2017

Recent Internet of Things(IoT), and in addition to wearable PC, such as software development methodologies based on a variety of object-oriented design and design patterns of GoF(Gang of Four) with OOP(Object-Oriented Programming) intended for portable devices. However, incorrect application design specification is that the higher the importance of the optimization of the program on the device because it can cause problems such as decreased operating speed, increase the memory occupancy and battery usage. In this paper, we propose an optimized design pattern based on the method of application, such as Android (Android) OS Strategy Pattern, State Pattern, Observer pattern. Test results show that the proposed scheme selection patterns can be selected to optimize the design pattern in the device that specification.

• Journal of the Korean Magnetics Society
• /
• v.23 no.2
• /
• pp.68-76
• /
• 2013

Currently, wireless power transmission technology based on magnetic induction was employed in battery charger for smart phone application. The system consists of wireless power transmitter in base station and receiver in smart phone. Size and thickness of receiver was strictly limited in the newest smart phone. In order to achieve high efficiency of a tiny small wireless power receiver module, sub-millimeter thick electromagnetic wave shielding sheet having high permeability and Q was essential component. It was found that magnetic field from transmitter to receiver can be intensified by sufficient shielding cause to minimize leakage magnetic flux by those magnetic properties. This leads to high efficiency of wireless power transmission and protects crucial integrated circuit of main board from electromagnetic noise. The important soft magnetic materials were introduced and summarized for the current small-power wireless power charger and NFC application and mid-power home appliance and high-power automotive application in the near future.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.4
• /
• pp.461-466
• /
• 2020

There are many application fields of electrical energy storage such as load shifting, integration with renewables, frequency or voltage supports, and so on. Especially, the frequency regulation is needed to stabilize the electric power system, and there have to be more than 1 GW as power reserve in Korea. Ni-rich layered oxide cathode materials have been investigated as a cathode material for Li-ion batteries because of their higher discharge capacity and lower cost than lithium cobalt oxide. Nonetheless, most of them have been investigated using small coin cells, and therefore, there is a limit to understand the deterioration mode of Ni-rich layered oxides in commercial high energy Li-ion batteries. In this paper, the pouch-type 20 Ah-scale Li-ion full cells are fabricated using Ni-rich layered oxides as a cathode and graphite as an anode. Above all, two test conditions for the application of frequency regulation were established in order to examine the performances of cells. Then, the electrochemical performances of two types of Ni-rich layered oxides are compared, and the long-term performance and degradation mode of the cell using cathode material with high nickel contents among them were investigated in the frequency regulation conditions.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.2
• /
• pp.144-151
• /
• 2022

In this paper, a 1.5V 256kb eFlash memory IP with low area DC-DC converter is designed for battery application. Therefore, in this paper, 5V NMOS precharging transistor is used instead of cross-coupled 5V NMOS transistor, which is a circuit that precharges the voltage of the pumping node to VIN voltage in the unit charge pump circuit for the design of a low-area DC-DC converter. A 5V cross-coupled PMOS transistor is used as a transistor that transfers the boosted voltage to the VOUT node. In addition, the gate node of the 5V NMOS precharging transistor is made to swing between VIN voltage and VIN+VDD voltage using a boost-clock generator. Furthermore, to swing the clock signal, which is one node of the pumping capacitor, to full VDD during a small ring oscillation period in the multi-stage charge pump circuit, a local inverter is added to each unit charge pump circuit. And when exiting from erase mode and program mode and staying at stand-by state, HV NMOS transistor is used to precharge to VDD voltage instead of using a circuit that precharges the boosted voltage to VDD voltage. Since the proposed circuit is applied to the DC-DC converter circuit, the layout area of the 256kb eFLASH memory IP is reduced by about 6.5% compared to the case of using the conventional DC-DC converter circuit.