• 한국염색가공학회지
• /
• 제8권3호
• /
• pp.59-65
• /
• 1996

Cotton fabrics were treated by low temperature plasma and/or cellulase, and its physical and dyeing properties were investigated. All the pretreatments of the cotton with low temperature plasma of oxygen, nitrogen and argon slowed down the rate of weight loss of cotton in cellulase solution. Plasma pretreatment did not show any strength retention effect on cotton fiber in the subsequent cellulase treatment. Pretreatment of cotton with low temperature oxygen plasma decreased the rate of dyeing in direct dye bath, while cellulase or plasma/cellulase pretreatment increased the rate. Equilibrium dye uptake of cotton was not changed greatly by the pretreatments except the normal untreated cotton showed more or less high uptake. The pretreatment of cellulase with a water-soluble carbodiimide reduced the enzymatic activity, and did not show any strength retention of cotton in enzymatic weight loss.

• 농업과학연구
• /
• 제13권1호
• /
• pp.82-89
• /
• 1986

본(本) 실험(實驗)은 hamster 수정란(受精卵)의 동결보존시(凍結保存時) 가장 적합(適合)한 동결(凍結)및 융해온도(融解溫度)를 구명(究明)하기 위(爲)하여 실시(實施)하였다. 수정란(受精卵)은 hamster 두당(頭當) 30 IU의 PMSG를 복탈내(腹脫內)에 투여(投與)하고 4일후(日後)에 교미(交尾)를 시켰으며 교미(交尾) 3일후(日後)에 도살(屠殺)하여 자궁(子宮)과 난관(卵管)을 관류(灌流)하여 회수(回收)하였다. 회수(回收)된 수정란(受精卵)의 동결(凍結)에 사용(使用)한 보존액(保存液)은 Dulbecco's phosphate buffered saline(PBS)이었으며, 동해방지제(凍害防止劑)로는 Dimetyl sulfoxide (DMSO)로서 3단계(段階)로 최종농도(最終濃度)가 1.5M이 되게 하였다. 수정란(受精卵)의 동결방법(凍結方法)은 실온(室溫)에서 $-6^{\circ}C$까지 $1^{\circ}C/min$의 속도(速度)로 하강(下降)시켜 수직(水植)하고 3 분간(分間) 방치(放置)시킨 다음 $0.30^{\circ}C/min$ 속도(速度)로 $-35^{\circ}C$까지 냉각(冷却)시켰으며, 다음에 $-70^{\circ}C$까지는 $0.1^{\circ}C/min$, $1^{\circ}C/min$ 및 $10^{\circ}C/min$의 3 처리(處理)로 냉각(冷却)시킨후 $-196^{\circ}C$의 액체질소(液體窒素)에 보존(保存)하였다. 융해(融解)는 $4^{\circ}C/min$과 $12^{\circ}C/min$의 속도(速度)로 $37^{\circ}C$ 까지 가온(加溫)하는 방법(方法)과 $37^{\circ}C$의 water bath에서 2 분간(分間) 침지(沈漬)시키는 방법(方法)을 이용(利用)하였다. 평균배란점(平均排卵點)은 35.1개(個)인데 대하여 회수(回收)된 수정란(受精卵)은 27.0개(個)로서 회수율(回收率) 77.0% 였으며, 수정란(受精卵)중에서 8세포기(細胞期) 배(胚) 24.8개(個)로서 그 비율(比率)은 70.6%였다. 수정란(受精卵)의 동결속도(凍結速度)에 따른 생존율(生存率)은 $0.1^{\circ}C/min$으로 동결(凍結)했을 때 55.5~67.7%, $1^{\circ}C/min$에서는 58.8~64.9%, $10^{\circ}C/min$에서는 40.5~44.7%였는데 $10^{\circ}C/min$의 속도(速度)로 동결(凍結)한 것이 유의(有意)하게 나쁜 성적(成績)이었다. 융해방법(融解方法)에 따른 수정란(受精卵)의 평균생존율(平均生存率)은 $4^{\circ}C/min$에서 53.5%, $12^{\circ}C/min$에서 53.7%, $37^{\circ}C$ water bath 융해(融解)에서 59.1%를 나타내어 water bath 융해(融解)가 가장 좋은 성적(成績)이었으나 큰 차이(差異)는 인정(認定)되지 않았다. 본(本) 실험(實驗)의 결과(結果)를 종합(綜合)해 볼 때 hamster 난자(卵子)의 동결(凍結)에는 실온(室溫)에서 $-6^{\circ}C$까지는 $1^{\circ}C/min$, $-35^{\circ}C$까지 $0.3^{\circ}C/min$, $-70^{\circ}C$까지 $0.1^{\circ}C/min$ 또는 $1^{\circ}C/min$의 동결속도(凍結速度)를 유지(維持)하고, $37^{\circ}C$의 water bath에서 2 분간(分間) 침관(沈漬)하여 융해(融解)하는 것이 가장 높은 생존율(生存率)을 얻었다.

• 한국표면공학회지
• /
• 제37권2호
• /
• pp.80-85
• /
• 2004

Chromium-carbon (Cr-C) and chromium-carbon-phosphorus (Cr-C-P) alloy deposits using trivalent chromium sulfate baths containing potassium formate were prepared to study their current efficiency, hardness change and phase transformations behavior with heat treatment, respectively. The current efficiencies of Cr-C and Cr-C-P alloy deposits increase with increasing current density in the range of 15-35 A/dm$^2$. Carbon content of Cr-C and phosphorous of Cr-C-P layers decreases with increasing current density, whereas, the carbon content of Cr-C-P layer is almost constant with the current density. Cr-C deposit shows crystallization at $400^{\circ}C$ and has (Cr+Cr$_{ 23}$$C_{6}$) phases at $800^{\circ}C$. Cr-C-P deposit shows crystallization at $600^{\circ}C$ and has (Cr+Cr$_{23}$ $C_{6}$$+Cr_3$P) phases at $800^{\circ}C$. The hardness of Cr-C and Cr-C-P deposits after heating treatment for one hour increase up to Hv 1640 and Hv 1540 and decrease about Hv 820 and Hv 1270 with increasing annealing temperature in the range of $400～^{\circ}C$, respectively. The hardness change with annealing is due to the order of occurring of chromium crystallization, precipitation hardening effect, softening and grain growth with temperature. Less decrease of hardness of Cr-C-P deposit after annealing above $700^{\circ}C$ is related to continuous precipitation of $Cr_{23}$ $C_{6}$ and $Cr_3$P phases which retard grain growth at the temperature.

• 패션비즈니스
• /
• 제20권3호
• /
• pp.119-132
• /
• 2016

Weighting of silk fabrics have long been practiced in silk fabric trading based on the primary consideration of price-weight, and secondary one of quality improvement in handle, luster, and drape properties. Recent trend of practicing weighting of silk fabrics is, however, focused on the improvement of the handle, luster, drape, and other properties. During the finishing processes of synthetic fiber, nylon, comprising amide structure, include the use of tannic acid, especially in the dyeing. A multitude of studies are being implemented in terms of improving fastness to washing, fastness to light of dyed nylon product, or the light fastness of nylon 6 itself. In this study, the effects of various tannic acid treatments on the physical properties related to the handle of nylon 6 and silk fabrics are examined and reviewed. The effects of treatment condition of the tannic acid, e.g., the concentration of the aqueous tannic acid solution, treatment time, and temperature were investigated. As the concentration of the aqueous solution of tannic acid increased, the bending rigidity values of the silk and nylon 6 fabrics increased. The treated fabrics felt stiff to the touch. Within the mild conditions of bending employed in the bending measurement of KES, nylon 6 treated fabric specimen exhibited a trend of improvement of bending resiliency within the range of small bending deformation. The weight of treated fabrics have all increased. The air-permeability values decreased as the treatment concentration increased. However, the decrease tendency of air permeability values may be alleviated by adjusting the fabric count during the tentering or expanding processes, either by tension adjustment or heat treatment. Optimum conditions of the treatment for nylon 6 are 1.25% tannic acid concentration, bath temperature of $85^{\circ}C$, pH 3.1, and those for silk fabric treatment are 1.25% tannic acid concentration, bath temperature of $85^{\circ}C$, pH 3.1. The treatment conditions will lead to the improvement in the properties of fabrics for summer.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.148-154
• /
• 2018

When shooting small arms, the inner surface temperature is heated up to about $700{\sim}1,000^{\circ}C$ by the friction of the bullet and the inner wall of the barrel and the combustion of propellant. High-temperature propellant gas and high-speed movement of the bullet cause corrosion of the inner wall, which is noticeable immediately in front of the chamber. In this study, the mechanical properties of Cr-Mo-V steel, which is the base material, were tested using Taguchi experimental design to find the best nitriding treatment conditions. For the nitriding process, the working time, salt bath temperature, and salt concentration were combined as three conditions and placed in the $L_9(3^4)$, orthogonal array table. The thicknesses of the white layer and the nitrogen diffusion layer were measured after nitriding under each condition in a salt bath furnace. Durability was evaluated by measuring the degree of dispersion through actual shooting because it was difficult to evaluate the mechanical properties of the cylinder inner structure. As a result, it was confirmed that the durability was optimal at $565^{\circ}C$, 1 hour, 0.5%. These optimal conditions were selected by the statistical analysis of the Minitab program(ver.17).

• 한국물환경학회지
• /
• 제25권4호
• /
• pp.522-529
• /
• 2009

To supply safe drinking water to areas lacking in water supply and drainage system, such as rural area and military bases in proximity to Demilitarized Zone, effective method for treating organic contaminants such as MTBE is required. This study focuses on seeking optimal conditions for effective degradation of MTBE using a bath type ultrasound reactor. Effectiveness of MTBE degradation by ultrasound is dependent on the frequency, power, temperature, treatment volume, initial concentration, catalyst, etc. In this study the degradation rate of MTBE by ultrasound was proportional to power/unit volume ratio and removal is relatively more efficient for 0.1 mM than for 1 mM of MTBE solution. Efficiency of ultrasound treatment for 1 mM MTBE solution was enhanced under bath temperature of $30^{\circ}C$ compared to $4^{\circ}C$, but the temperature effect was negligible for 0.1 mM MTBE solution. Also for 0.1 mM MTBE solution, effect of catalyst such as $TiO_2$ and $Fe^0$ on treatment speed was negligible, and zeolite even increases the time taken for the degradation. Under these specific experimental conditions of this study, the most determinant factor for degradation rate of MTBE in solution was frequency and power of ultrasound. The results have shown that a continuous ultrasound reactor system can be used for small scale remediation of organically polluted groundwater, under optimal conditions.

• 한국산림과학회지
• /
• 제65권1호
• /
• pp.31-42
• /
• 1984

본(本) 연구(硏究)는 아직 연구(硏究)의 초창기적(初創期的) 단계(段階)에 있는 삼림욕(森林浴)에 대(對)한 과학적(科學的)인 근거(根據)와 삼림욕장(森林浴場) 설계(設計)에 필요(必要)한 개념(槪念) 특(特)히 삼림욕(森林浴)의 정의(定義), 기본행태(基本行態)와 시설(施設) 및 수용력(收容力) 결정(決定)에 관한 사항과 삼림욕장(森林浴場) 조성시(造成時) 고려점(考慮點)을 밟히는 내용(內容)으로 되어 있다. 삼림욕(森林浴) 발생(發生)의 동인(動因)이 된 terpene은 인체(人體)에 유효(有效)한 작용(作用)을 하고 있음이 밝혀졌고 그 물질(物質)은 하루 중에는 정오(正午) 경(頃)과 아침에, 연(年) 중(中)에는 봄 여름에 많이 발산(發散)되고 있다. 발산(發散)에 영향(影響)을 주는 제일인자(第一因子)는 기상인자일풍(氣象因子一風), 온도(溫度), 일사량(日射量), 관계습도일(關係濕度一)이며, 목관록폐도(木冠麓閉度)와 엽량(葉量)도 발산량(發散量)의 농도(農度)에 관계(關係)하고 있다. 삼림욕(森林浴)의 기본행태(基本行態)는 주로 정적(靜的)인 행태(行態)이며 시설(施設) 또한 그렇다. 1인당(人當) 필요(必要)한 삼림면적(森林面積)인 삼림욕방(森林浴房)의 크기는 $169m^2$이며 ha당(當) 59인(人)이다. 삼림욕장(森林浴場)의 입지(立地)는 국(國) 도립공원(道立公園), 계류지(溪流地), 온천지대(溫泉地帶), 수변지(水邊地) 등에 인접하여 있는 것이 좋다. 한편, 삼림욕장(森林浴場)의 삼림관리(森林管理)는 terpene 발산량(發散量)을 일정(一定)하게 유지(維持)하고 삼림생태계(森林生態系)의 균형(均衡)이 파괴되지 않도록 실시(實施)돼야 한다.

• Journal of Ginseng Research
• /
• 제36권4호
• /
• pp.430-441
• /
• 2012

This study was conducted to evaluate the effects of natural bioactive products such as Manda enzyme (T1), Yangmyeongwon (T2), effective microorganisms (T3), and Kelpak (T4) on the growth and ginsenoside contents of Panax ginseng cultured in an aeroponic system using a two-layer vertical type of nutrient bath under natural light conditions. The growth of ginseng plants showed specific characteristics according to the positions in which they were cultured due to the difference of light transmittance and temperature in the upper and lower layers during aeroponic culture in a two-layer vertical type of system. The growth of the aerial part of the leaves and stems of ginseng plants cultured in the lower layer (4,000 to 6,000 lx, $23^{\circ}C$ to $26^{\circ}C$) of the nutrient bath was observed to be superior to that of the ginseng plants cultured in the upper layer (12,000 to 15,000 lx, $25^{\circ}C$ to $28^{\circ}C$). The leaf area was significantly larger in the treatment of T2 and T4 (46.70 $cm^2$) than with other treatments. Conversely, the values of the root weight and root diameter were higher in ginseng plants cultured in the upper layer of the nutrient bath. The root weight was significantly heavier in the treatment of T4 (6.46 g) and T3 (6.26 g) than with other treatments. The total ginsenoside content in the leaves and roots was highest in the ginseng plants cultured by the treatment of T1, at 16.20%, while the total ginsenoside content obtained by other treatments decreased in the order of T4, T5 (control), T2, and T3, at 13.21%, 12.30%, 14.84%, and 14.86%, respectively. The total ginsenoside content of the ginseng leaves was found to be significantly higher in the treatment of T1 in the lower layer of the nutrient bath, at 15.30%, while the content of the ginseng roots in the treatments of T3 and T4, at 1.27% and 1.23%, respectively, was significantly higher than in other treatments in the upper layer of the nutrient bath.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.1942-1947
• /
• 2007

A thermoelectric module can be used for cooling or power generation. The basic requirements to achieve a significant thermoelectric performance are the same for both generators and coolers. Thermoelectric modules with $Bi_2Te_3$ materials are usually employed in the cooling applications below room temperature but it can also be used for the power generation in the similar temperature range. In the present study, the power generation with a $Bi_2Te_3$ thermoelectric module has been investigated. The temperature difference between the hot and cold sides of the module is maintained with electric heater and cold water from the circulating water bath. The result shows that the electric current generated increases with temperature difference and decreases with the load resistance. However, the voltage increases with both the temperature difference and load resistance. The electric power increases with temperature difference and it has the maximum value when the load resistance is about 4 ${\Omega}$ for a given device.

• 한국의류산업학회지
• /
• 제2권5호
• /
• pp.405-410
• /
• 2000

The effects of individual sweating rates on thermophysiological responses during the decrease phase of clothing surface temperature (Tcs) with cotton (C) and polyester (P) clothed subjects were examined. Seven women subjects were exposed in a climatic chamber at ambient temperature of $27.2^{\circ}C$, relative humidity of 50%, and their lower-legs were immersed in a water bath at a temperature of $35-41^{\circ}C$ for 70 min. During water immersion, Tcs in C-clothed subject rose immediately after the onset of sweating and then Tcs fell gradually. In C-clothed subjects, Tcs decreased directly (p<0.05) in proportion to total sweating rate (TSR), however no significant correlation was observed in P-clothed subjects. The relationship between TSR and changes in mean skin temperature, and skin blood flow showed negative correlation when wearing C-clothing (p<0.05), however, no significant correlation when wearing P-clothing. Individual TSR was correlated with threshold rectal temperature for sweating onset (p<0.05) with C- and P-clothed subjects. The results showed that individual TSR had significant effects on not only Tcs but also on thermoregulatory responses during the Tcs decrease phase.