• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 가을 학술발표회 논문집
• /
• pp.45-52
• /
• 2001

A series of unreinforced masonry (URM) walls were analytically investigated for a limited version of seismic in-plane performance. For this URM walls were assumed to be an elastic continuum and modeled as isotropic plane stress elements within which the nature of cracking was propagated. Accordingly, cracking mode of behavior in URM was modeled by smeared-crack approach. Total of 70 cases were considered for various parameters such as axial load ratio, aspect ratio and effective section area ratio due to the existence of opening, etc. The analysis results indicated a general tendency in base shear coefficient and deformability of URM walls for these variables.

• 대한치과교정학회지
• /
• 제17권1호
• /
• pp.135-148
• /
• 1987

To investigate the relationship between craniofacial growth and bone maturity of the hand wrist in normal occlusion, the author took cephalogram and handwrist radiogram of 391 students (male 192, female 199) and assessed the measurements of cephalogram according to skeletal maturity stages of the hand and wrist. In this study, four skeketal stages and 36 linear, angular measurements of the cephalometrics were selected. In hand-wrist X-ray the bones used to determine skeletal maturity were the middle phalanges of the third finger, and distal epiphysis of the radius. In cephalogram, the landmark used to measure the angle and length were N, S, Po., Ar., Go., Me., Gn., Pog., Point B, Point A, ANS, PNS, Or., U1, L1, U6, L6 etc.. The results were as follows, 1. The table of mean, standard deviation, p-value from measurements were made in each group and both sex. 2. The increased measurements according to skeletal maturity were anterior cranial bese length, posterior cranial base length, ramus height, anterior facial height, posterior facial height, L1 to mandibular plane (mm), facial plane angle. In contrast to, decreased measurements were genial angle, facial cnvexity and facial plane angle. 3. Denture pattern measurements (IMPA, FMIA, occlusal plane to Go-Gn, interincisal angle, U1 to SN plane, U1 to SN plane, U1 to facial plane, L1 to facial plane etc.) .had nothing to do with skeletal maturity. 4. Skeletal maturity had close relationship with craniofacial growth, but had little to do with tooth development.

• Wind and Structures
• /
• 제11권5호
• /
• pp.377-389
• /
• 2008

An experimental investigation has been conducted to determine the effectiveness of base shield plates in reducing the drag of a rough circular cylinder in a cross flow at Reynolds numbers in the range $3{\times}10^4{\leq}Re{\leq}10.5{\times}10^4$. Three model configurations were investigated and compared: a plane cylinder (PC), a cylinder with a splitter plate (MC1) and a cylinder fitted with base shield plates (MC2). Each configuration was studied in the sub and supercritical flow regimes. The chord of the plates, L, ranged from 0.22 to 1.50D and the cavity width, G, between the plates was in the range from 0 to 0.93D. It is recognized that base shield plates can be employed more effectively than splitter plates to reduce the aerodynamic drag of circular cylinders in both the sub- and supercritical flow regimes. For subcritical flow regime, one can get 53% and 24% drag reductions for the MC2 and MC1 models with L/D=1.0, respectively, compared with the PC model. For supercritical flow regime however, the corresponding drag reductions are 38% and 7%.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제26권3호
• /
• pp.229-237
• /
• 2000

According to the functional matrix theory, Delaire proposes that individual occlusal plane was determined by variable effects of teeth, maxilla, mandible, cranium, cranial base and soft tissue matrix including the orofacial musculature. and that there is the ideal occlusal plane determined by the most proper spatial position of maxilla and mandible, functionally and esthetically. This study was designed to find out the relation between Delaire's ideal occlusal plane and muscle activity of masticatory muscles in individuals who have normal maxillo-mandibular relationships. Lateral cephalometric radiographs were taken and his/her individual occlusal plane and ideal occlusal plane were analyzed with Delaire's architectural and structural craniofacial analytic method. For evaluation of muscle activities of masticatory muscles, electromyography of anterior temporal muscle, superficial masseter muscle, and anterior belly of digastric muscle was recorded in fifty Korean normal Angle class I occlusion individuals. According to the average value of ideal occlusal plane, fifty normal Angle class I occlusion individuals were classified into three groups: Ideal occlusal plane group(I group), hyperrotation group(I+ group) and hyporotation group(I- group). The result of this study was as follows: 1. The results of Delaire's architectural and structural craniofacial analysis of lateral cephalography of the fifty Korean normal Angle class I occlusion individuals are that twelve persons(24%) have consistent or parallel with ideal occlusal plane and the average of angular difference was $1.22^{\circ}{\pm}3.69^{\circ}$. 2. There is no significant difference in muscle activities of masticatory muscles during resting(p<0.05), but significant increases of muscle activity of ipsilateral anterior temporal and masseter muscle, contralateral anterior belly of digastric muscle during unilateral chewing and of anterior temporal and masseter muscle during bilateral clenching(p<0.05). 3. To find out the effect of the angular difference between Delaire's ideal occlusal plane and real occlusal plane to muscle activity, muscle activities of masticatory muscles were compared with three groups in each other; I group, I+ group and I- group. The results were no significant differences during resting, unilateral chewing and bilateral clenching.(p>0.05) 4. Although there is no significant differences of masticatory muscle activities among the three groups, the fact that increasing tendency of masseter muscle activity of ideal occlusal plane group(I+) than those of any other groups(I+ and I-) during bilateral clenching was noted. There is only the implication that occlusal plane makes some effects on masticatory muscle activities, espacially that of masseter muscle during bilateral clenching. In conclusion, the hypothesis that occlusal plane is one of the factors which affect the muscle activities of masticatory muscles and that anyone whose occlusal plane consistent with Delaire's ideal occlusal plane has an extraordinary functional advantage in masticatory muscle function cannot be proven with electromyography methods.

• The Journal of Advanced Prosthodontics
• /
• 제5권1호
• /
• pp.9-15
• /
• 2013

PURPOSE. The purpose of this study was to determine accurately the part of the tragus to be used to form the Ala-Tragal line or Camper's line in orthognathic profile patients. MATERIALS AND METHODS. 150 dentate subjects with age of 18-40 years with orthognathic profile were sampled. Life-size lateral digital photographs of the face with fox plane were taken in natural head position. Different angles between Eye-Ear plane and occlusal plane ($OT_1$-OP), Eye-Ear plane and ala-superior border of tragus ($OT_1-AT_1$), Eye-Ear plane and ala-middle border of tragus ($OT_1-AT_2$) and Eye-Ear plane and ala-inferior border of tragus ($OT_1-AT_3$) were calculated using computer software package, AutoCAD 2004. From the three angles formed by the Eye-ear plane ($OT_1$ or FH plane) and the ala-tragal lines, the one closest to the angle formed between Eye-Ear plane ($OT_1$) and occlusal plane (OP) was used to determine the occlusal plane of orientation. The obtained results were subjected to ANOVA F test, Tukey's Honestly significant difference test, followed by Karl Pearson coefficient of correlation test. P values of less than 0.05 were taken as statistically significant. RESULTS. The mean of base line angle i.e. $OT_1$-OP angle ($11.96{\pm}4.36$) was found to be close to $OT_1-AT_2$ angle ($13.67{\pm}1.93$) and $OT_1-AT_3$ angle ($10.31{\pm}2.03$), but $OT_1$-OP angle was found to be more closer to $OT_1-AT_3$ angle. Comparison of mean angles showed that $OT_1$-OP angle in both males (11.68) and females (12.51) is close to $OT_1-AT_3$ angle (males- 11.01, females- 11.95). CONCLUSION. The line joining from ala to the lower border of the tragus was parallel to the occlusal plane in 53.3% of the subjects. There was no influence of the sex on the level of occlusal plane.

• 대한치과교정학회지
• /
• 제5권1호
• /
• pp.57-63
• /
• 1975

For the purposes of augmentation of the aid for case analysis and diagnosis of malocclusion, a roentgenocephalometric study was made from 84 Korean adolescences. The Subjects consist of 42 males and 42 females aged from 17 to 20 years with normal occlusion and acceptable facial appearance. The author measured 18 angles and 14 linear distances as suggested by Jarabak. The following results were obtained. 1) Each linear measurement of the males' skull was greaten than that of the females. 2) The posterior to anterior facial height was $69.2\%$ in the males and $67.1\%$ in the females. 3) In the relationship of upper lip to esthetic line, the lip of females was more behind than that of males. 4) Saddle angle was $124.7^{\circ}$, articular angle was $148.7^{\circ}$, genial angle was $119.4^{\circ}$ and upper and lower genial angles were $45.1^{\circ}\;(N-Go-a^{\circ})$ and $74.2^{\circ}\;(N-Go-Me^{\circ})$. 5) The ratio of mandibular body to anterior cranial base was about 1:1. 1. 6) The angulations of $SNA^{\circ},\;SNB^{\circ}\;and\;SNP^{\circ}$ were as follows; $SNA^{\circ},\;80.3^{\circ},\;SNB^{\circ},\;79.8^{\circ},\;SNP^{\circ},\;81.1^{\circ}$. 7) The angle of the sella-nasion plane to the mandibular plane $(SNG^{\circ}Me^{\circ})$ was $32.0^{\circ}$ and that of the occlusal plane to the mandibular plane was $18.2^{\circ}$. 8) The angle of the maxillary central incisor to the sellanasion plane $(1-SN^{\circ})$ was $105.6^{\circ}$. That of the mandibular central incisor to the mandibular plane $(1-GoMe^{\circ})$ was $94.0^{\circ}$, and the interincisal angle $(1\;to\;1^{\circ})$ was $127.6^{\circ}$. 9) The linear distance from incisal edge of upper central incisor to facial plane was 8.0mm and that of lower central incisor was 4.6mm. 10) In the relationship of the lower lip to the esthetic line, the lower lip was 0.2mm front of the esthetic line.

• 대한기계학회논문집A
• /
• 제28권12호
• /
• pp.1871-1876
• /
• 2004

We demonstrate a novel fabrication technology for the microneedle array that can be used in the medical test field, which is transdermal drug delivery and blood analyte sampling. Previous researchers have used silicon-processed micromachining, a reactive ion etching, and molding techniques for the fabrication of microneedle array. However, these fabrication techniques have somewhat limitations apply to the microneedle array fabrication according to its application. Inclined LIGA process is suggested to overcome these problems. This process provides easier, sharper and longer out-of-plane microneedle array structure than conventional silicon-processed fabrication method did. Additionally, because of the advantage of the LIGA process based on mold fabrication for mass production, the polymer, PMMA(PolyMethylMethAcrylate), based microneedle array is useful as the mold base of nickel electroplating process; on the other hand, silicon-processed microneedle array is used in itself. In this research, we fabricate different types of out-of-plane microneedle array, which have different shape of tip, base and hole structure, using the inclined LIGA process. The fabricated microneedles have proper mechanical strength, height and sharpness to puncture human hand epidermis or dermis with less pain and without needle tip break during penetrating the skin.

• Nuclear Engineering and Technology
• /
• 제48권1호
• /
• pp.259-267
• /
• 2016

Most manufacturing processes, including welding, create residual stresses. Residual stresses can reduce material strength and cause fractures. For estimating the reliability and aging of a welded structure, residual stresses should be evaluated as precisely as possible. Optical techniques such as holographic interferometry, electronic speckle pattern interferometry (ESPI), Moire interferometry, and shearography are noncontact means of measuring residual stresses. Among optical techniques, ESPI is typically used as a nondestructive measurement technique of in-plane displacement, such as stress and strain, and out-of-plane displacement, such as vibration and bending. In this study, ESPI was used to measure the residual stress on the welded part of butt-welded American Society for Testing and Materials (ASTM) A36 specimens with $CO_2$ welding. Four types of specimens, base metal specimen (BSP), tensile specimen including welded part (TSP), compression specimen including welded part (CSP), and annealed tensile specimen including welded part (ATSP), were tested. BSP was used to obtain the elastic modulus of a base metal. TSP and CSP were used to compare residual stresses under tensile and compressive loading conditions. ATSP was used to confirm the effect of heat treatment. Residual stresses on the welded parts of specimens were obtained from the phase map images obtained by ESPI. The results confirmed that residual stresses of welded parts can be measured by ESPI.

• Advances in concrete construction
• /
• 제8권2호
• /
• pp.77-90
• /
• 2019

This paper aims to investigate vibration frequency decrease (vibration period elongation) of reinforced concrete (RC) structure with unreinforced infill wall and reinforced infill wall exposed to progressively increased artificial earthquake load on shaking table. For this purpose, two shaking table experiments were selected as a case study. Shaking table experiments were carried on 1:1 scaled prototype one bay one storey RC structure with infill walls. The purpose of this shaking table experiment sequence is to assess local behavior and progressive collapse mechanism. Frequency decrease and eigen-vector evolution are directly related to in-plane and out-of-plane bearing capacities of infill wall enclosure with reinforced concrete frame. Firstly, frequency decrease-damage relationship was evaluated on the base of experiment results. Then, frequency decrease and stiffness degradation were evaluated with applied Peak Ground Acceleration (PGA) by considering strength deterioration. Lastly, eigenvector evolution-local damage and eigenvector evolution-frequency decrease relationship was investigated. Five modes were considered while evaluating damage and frequency decrease of the tested specimens. The relationship between frequency decrease, stiffness degradation and damage level were presented while comparing with Unreinforced Brick Infill (URB) and Reinforced Infill wall with Bed Joint Reinforcement (BJR) on the base of natural vibration frequency.

• 한국공간구조학회논문집
• /
• 제21권4호
• /
• pp.23-30
• /
• 2021

In this paper, a twisted shape structure with an elevation form favorable to the resistance of vibration caused by wind loads is selected from among the forms of high-rise buildings. The analytical model is a square, triangular, and hexagonal plane with a plane rotation angle of one degree from 0 to 3 degrees per each story. As a result of the analysis, as the twist angle increased, story drift ratio is increased. Responses with different eccentricity rates were shown by analytical models. Therefore planar shapes designed symmetrically to the horizontal axis of X and Y are considered advantageous for eccentricity and torsion deformation. In the case of the bending moment of the column, the response was amplified in the column supporting the base floor, the roof floor, the floor in which the cross-section of the vertical member changes, and the floor having the same number of nodes as the base floor. Finally, the axial force response of the column is determined to be absolutely affected by the gravity load compared to the lateral load.