• The Korean Journal of Quaternary Research
• /
• v.21 no.1
• /
• pp.37-45
• /
• 2007

Skull base height increases significantly with better nutrition and health conditions. With coordinate caliper or by subtraction, skull base height is easily measured. To examine nutrition and health condition of MIA(missing in action) during the Korean War and people who lived during the 17-18 centry of the Late Chosun. This study is focused on the change of skull base height through time as seen in comparing 83 MIA cranium and 12 17-18 centry cranium of Korea with 219 modern American middle class adult cranium(Terry Collection and forensic skeleton). To sum up, nutritional condition of MIA is not significantly changed, as seen in comparing with nutritional condition of 17-18 century people.

• Geomechanics and Engineering
• /
• v.2 no.1
• /
• pp.29-44
• /
• 2010

Vertical vibration tests were conducted using model footings of different size and mass resting on the surface of finite sand layer with different height to width ratios which was underlain by either rigid concrete base, under both dry and saturated condition. The effect of saturation on the damping ratio of finite sand stratum underlain by a rigid base has been verified and compared with the results obtained for the case of finite dry sand stratum underlain by the rigid base. Comparison of results of the experimental study showed that the damping in both the cases is less than 10%. The damping ratio obtained for finite saturated sand stratum is marginally lower than that obtained on finite dry sand stratum at H/B ratio of 0.5. The difference between the two cases becomes significant when the H/B ratio increases to 3.0, indicating the significant influence of soil moisture on damping ratio of foundation- soil system with increase in the thickness of the finite sand stratum. Comparison of the predicted damping ratio for a homogeneous sand stratum with the experimental damping ratio obtained corresponding to the height to width ratio of 3.0 of the finite sand stratum underlain by the rigid concrete base indicates a significant reduction in damping ratio of the foundation-soil system for both the cases.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.6
• /
• pp.551-557
• /
• 1997

In mobile radio environment, it is well known that the base station antenna height gain factor is 6 dB / octave. But the mobile radio environment is not simple and affected by the terrain contour or the man-made structures, so the antenna height gain factor varies due to the propagation conditions. This paper represents the received signal power gain due to the base station antenna height in the microcell environment on the basis of the flat terrain and sloping terrain model. The gain point which shows the antenna height gain is derived in this paper.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.205-213
• /
• 2016

Heat loss and fin efficiency of symmetric and asymmetric trapezoidal fins with variable slope of fin's top surface are obtained by using a two-dimensional analytic method. Shapes of symmetric and asymmetric fins are changed from rectangular through trapezoidal to triangular by adjusting the fin shape factor. The ratio of symmetric trapezoidal fin length to asymmetric trapezoidal fin length is presented as a function of fin base height and convection characteristic number. The ratio of symmetric trapezoidal fin efficiency to asymmetric trapezoidal fin efficiency is presented as a function of the fin base height and fin shape factor. One of results shows that asymmetric trapezoidal fin length is shorter than symmetric trapezoidal fin length (i.e., asymmetric trapezoidal fin volume is smaller than symmetric trapezoidal fin volume) for the same heat loss when the fin base height and fin shape factor are the same.

• Industrial Engineering and Management Systems
• /
• v.6 no.2
• /
• pp.146-157
• /
• 2007

This paper discusses two algorithms for recommending notebook computer (NBC) and workstation adjustments so that the user can assume an ergonomic seated posture during NBC operation. Required input data are the user's anthropometric data and physical dimensions of the NBC and the workstation. The first algorithm is based on an assumption that there are no workstation constraints while the second algorithm considers the actual seat height and work surface height. The results from the algorithms include recommendations for adjusting the NBC (tilt angle of the NBC base unit, angle between the base and screen units, and base support height) and the workstation (heights of seat support and footrest, and distance between the body and the NBC).

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• v.14 no.3
• /
• pp.151-161
• /
• 2010

A reversed trapezoidal fin is analyzed using a two-dimensional analytical method. Heat loss from the reversed trapezoidal fin is presented as a function of the fin shape factor, fin base thickness and the fin base height. The relationship between the fin tip length and the convection characteristic number as well as that between the fin tip length and the fin base height for equal amounts of heat loss are analyzed. Also the relationship between the fin base thickness and the fin shape factor for equal amount of heat loss is presented. One of the results shows that the heat loss decreases linearly with the increase of the fin shape factor.

• Journal of Welding and Joining
• /
• v.26 no.2
• /
• pp.92-97
• /
• 2008

In welding of thin plate, some defects such as melt through and unmelted zone occur easily at welding start, however there is a limited study on those problems. Therefore the effects of start block and arc length on melt through and unmelted zone at start were investigated in this study. When start block height was lower than base metal, there was melt through at start. And when the height was even with base metal, no unmelted zone existed. Unmelted zone was increased as start block height increased from 0mm to 0.5mm. However unmelted zone was not much changed as the height increasing from 0.5mm to 1.0mm. When gap existed between start block and base metal, melt through occurred. However, unmelted zone was increased as the contact force of start block on base metal was increased from 0kgf to 7.5kgf. And when arc length was decreased from 3.8mm to 3.0mm, unmelted zone was decreased. It was concluded that the optimum condition to prevent melt through and to minimize unmelted zone would be with start block height 0.25mm, contact force 3.0kgf, and arc length 3.4mm. This optimum condition was applied to the mass production line and resulted in satisfied outcome.

• The korean journal of orthodontics
• /
• v.9 no.1
• /
• pp.133-140
• /
• 1979

The author compared patients showing two extremes of incisor vertical relationship to find out differences in craniofacial morphology which might influence face height and incisor overbite. The subjects consisted of 53 open-bite cases and the same number of deep-bite cases. The results were as follows: 1. On the average, the lower face height was significantly greater in open-bite cases than in deep-bite cases. 2. In open-bite cases, gonin-menton length was significantly greater than in deep-bite cases. In deep-bite cases, anterior cranial base length and posterior cranial base length were significantly greater in open-bite cases. 3. The jaw angle was significantly greater in open-bite cases. 4. The gonion-menton-nasion angle was significantly greater in deep-bite cases. 5. From geometric standpoint, the increase of jaw and joint angle would increase lower face height, but these two showed negative correlation. 6. The sizes of the jaw and joint angle might be factors of open-bite or deep-bite, but these were not the only variables that determined lower face height. 7. In open-bite cases, there was a closer correlationship between lower face height and the other linear measurments than in deep-bite cases. In deep-bite cases, there was a closer correlationship between lower face height and the other angular measurements than in open-bite cases. 8. Considering both linear and angular measurements of facial polygon, all contributed significantly to the lower face height. The nonsignificant variables were jaw and joint angle in open-bite cases, and anterior cranial base length, jaw angle, and joint angle in deep-bite cases.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.1
• /
• pp.65-72
• /
• 2009

For the evaluation of far-field performance by using the near-field probing on the base station dipole array antenna, the effects of mutual coupling depending on the heights between the array antenna with reflector and the probe were analyzed. When the height is varied in the near-field region, S parameters on the input ports of antenna and probe are measured and analyzed to decide the height for the minimum mutual coupling effect and the maximum probing efficiency. This height will be applicable to the near-field probing system design to achieve the precision far-field performance of a base station array antenna system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.1
• /
• pp.45-54
• /
• 2012

Optimization of the asymmetric trapezoidal fin with various upper lateral surface slope is made using a two-dimensional analytic method. For the fixed fin base height, the optimum heat loss, fin length and effectiveness are represented as inner fluid convection characteristic number, fin base thickness, fin base height, fin shape factor and ambient convection characteristic number. For this optimum procedure, the optimum heat loss is defined as 95% of the maximum heat loss from the fin. One of the results shows that optimum heat loss and effectiveness seems independent of the fin shape factor while optimum fin length decreases almost linearly as the fin shape factor increases.