• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.10-12
• /
• 1996

AlGaAs/GaAs Heterojunotion Bipolar Transistors (HBTs) with various emitter areas were fabricated and the device size dependence on the current gain was examined. With the different emitter areas, the passivated devices having the same peripheral length were fabricated and measured. The measured base current density in the Gummel plots shows an ideality factor of nearly 2. It is found that as the emitter area becomes small, the base current density with the ideality factor of 2 increases linearly, and as the emitter perimeter/area ratio becomes large, the surface recombination current density component increases. The current gain performance in AlGaAs/GaAs HBTs is mainly determined by either the larger emitter area or the smaller ratio of the emitter perimeter to the emitter area. These results will be compared with experimental works for GaInP/GaAs HBTs

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.12A
• /
• pp.1883-1890
• /
• 1999

Wireless communication in an urban area, the accurate prediction of wave propagation characteristics are very important to determine communication service areas, select optimal base-stations, and design cells, etc. The CCIR model is a propagation prediction model using a shadowing by the buildings in an urban area. This model represent the shadowing rate by the means of the effect of shadowing between base-station and mobile unit in a shaped linear plane. But, This one occurred a lot of prediction error because it did not consider that density area by the buildings and terrain configurations by the hill and mountain on Line-Of-Sight. In this thesis, an improved propagation prediction model is proposed to reduce prediction error. We presents a new equation, which is using the SAS. This equation is associated with the shadow height by the buildings that considers the topology and the number of blocks that can affect the building shadow in the Line-Of-Sight. We measure the received electrical field level of base-station that high density area, medium density area, and low density area, and then compare and analysis the result to prediction of CCIR model and proposed model. The result compared with the measurement, the proposed model has the improvement of 9.71dB in a high density area, 9.66dB in a medium density area, and 4.02dB in a low density area better than the CCIR model. The result compared with the measurement, the proposed model has the improvement of 9.71dB in a high density area, 9.66dB in a medium density area, and 4.02dB in a low density area better than the CCIR model.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.12
• /
• pp.51-59
• /
• 1993

A 4${\times}10^{19}cm^{3}$ carbon-doped base AlGaAs/GaAs HBY was grown using carbontetracholoride(CCl$_4$) by atmospheric pressure MOCVD. Abruptness of emitter-base junction was characterized by SIMS(secondary ion mass spectorscopy) and the doping concentration of base layer was confirmed by DXRD(double crystal X-ray diffractometry). Mesa-type HBTs were fabricated using wet etching and lift-off technique. The base sheet resistance of R$_{sheet}$=550${\Omega}$/square was measured using TLM(transmission line model) method. The fabricated transistor achieved a collector-base junction breakdown voltage of BV$_{CBO}$=25V and a critical collector current density of J$_{O}$=40kA/cm$^2$ at V$_{CE}$=2V. The 50$\times$100$\mu$$^2$ emitter transistor showed a common emitter DC current gain of h$_{FE}$=30 at a collector current density of JS1CT=5kA/cm$^2$ and a base current ideality factor of ηS1EBT=1.4. The high frequency characterization of 5$\times$50$\mu$m$^2$ emitter transistor was carried out by on-wafer S-parameter measurement at 0.1~18.1GHz. Current gain cutoff frequency of f$_{T}$=27GHz and maximum oscillation frequency of f$_{max}$=16GHz were obtained from the measured Sparameter and device parameters of small-signal lumped-element equivalent network were extracted using Libra software. The fabricated HBT was proved to be useful to high speed and power spplications.

• Korean journal of food and cookery science
• /
• v.19 no.6
• /
• pp.729-736
• /
• 2003

This study was performed to improve the quality and extend the shelf life of Yukwa and Salyeotgangjung, traditional Korean cookies, by using fine hot salt instead of oil as the popping medium. Yukwa and Salyeotgangjung were popped with fine salt, and the size, sensory evaluation, color values and textural properties were then compared with those popped in oil. The results showed that the Yukwa base with salt was popped the most at 140C and the rice was popped at 240C. The Yukwa base in salts was smaller in size and larger in density than in oil but the popped rice in salts had a similar size and a smaller density than that popped in oil. In the sensory test, the Yukwa base and popped rice expanded in the salts were preferred to those popped in oil but there was little difference in only popped rice. In terms of color, there was a difference between those popped in salt and in oil. In terms of texture, only popped rice expanded in the salts was harder than in oil, and the Yukwa popped in oil was more cohesive than in the salts. In brittleness, there were no differences between in salt and in oil.

• Steel and Composite Structures
• /
• v.17 no.4
• /
• pp.535-548
• /
• 2014

In this paper, the exact closed-form solutions for torsional analysis of heterogeneous magnetostrictive circular cylinder are derived. The cylinder is subjected to the action of a magnetic field produced by a constant longitudinal current density. It is also acted upon by a particular kind of shearing stress at its upper base. The rigidity of the cylinder is graded through its axial direction from one material at the lower base to another material at the upper base. The distributions of circumferential displacement and shear stresses are presented through the radial and axial directions of the cylinder. The influence of the magnetostrictive parameter is discussed. The effects of additional parameters are investigated.

• Journal of the Korean institute of surface engineering
• /
• v.28 no.4
• /
• pp.243-254
• /
• 1995

The fabrication process of Cu-base anode for replacing Ni-base anode of molten carbonate fuel cell was investigated. Electrochemical performance and thermal stability of Cu-base anode were also investigated. Green sheet was prepared by mixing Cu and Ni powder with 1.5wt% methylcellulose and 100wt% water. The pore-size distribution of the Cu-base anode sintered at $800^{\circ}C$ for 30min showed almost uniform pore-size ranging from 4 to 20$\mu\textrm{m}$ and it was considered suitable for MCFC anode. Cu-Ni anode containing between 35 to 50wt% Ni exhibited current density of 111mA/$\textrm{cm}^2$ at 100mV overpotential and it was almost the some value for pure Ni anode. The sintering resistance of Cu-Ni increased with an increase of Ni addition. It was considered that the increase of sintering resistance was due to the decrease of diffusion rate of Cu and Ni with increasing the addition of Ni in Cu-Ni alloy.

• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.4
• /
• pp.200-207
• /
• 2006

In addition to the basic properties of the base and top coating agents, corrosion resistance of non-chrome magni 565 coating and characteristics of coating film when coated to steel substrate were studied. The system had a good wettability at room temperature. Moreover, both the contact angle and surface tension were affected little by the viscosity of coating agent and surface roughness of the steel substrate. And the samples coated with optimal conditions showed a great corrosion resistance in salt spray test with 1500 hours or longer of initial appearance time of rust. The coating film was composed of overlapping layer of zinc and aluminium flakes, and the thickness of base coat increased with an increase of base coat viscosity. Based on the C-F peaks of 1,1-Difluoroethaen homo-polymer, it was thought that the base coat was an inorganic polymer bond layer. Meanwhile, the top coat showed C-F peaks of polytetrafluoroethylene with C-H peaks of phenol in FT-IR analysis. From the lower weight loss of base coat in TG analysis, it was thought that cross linking density of base coat was larger than that of top coat. It was thought that the small exothermic reactions observed in DSC curves were due to the thermosetting resins contained in the coating agents. Compared to the non-coated specimen, the coated sample showed more higher polarization resistance and corrosion potential with lower corrosion current density.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1999.04a
• /
• pp.178-185
• /
• 1999

Minimum life-cycle cost helps to evaluate cost effectiveness of base-isolated bridges under specific condition. Life-cycle cost mainly consists of the initial construction cost and the expected damage cost. Damage cost estimation needs proper model of input ground motion failure probability evaluation method and limit states definition. We model the input ground motion as spectral density function compatible with the response spectra defined at each seismicity and site condition. Spectrum analysis and crossing theory is suitable for reseating calculation of failure probabilities in the process of cost minimization. Limit states of base-isolated bridges re defined for superstructure isolator and pier respectively The method is applied to both base-isolated bridges and conventional bridges under the same conditions to investigate cost effectiveness of base isolation in low and moderate seismic region. the results show that base-isolation of bridges are more effective in low and moderate seismic region and that the site effects on the economical efficiency may not be negligible in such a region.

• Journal of Forest and Environmental Science
• /
• v.31 no.4
• /
• pp.267-271
• /
• 2015

The variations of wood density and mechanical properties of Juniperus polycarpos trees were studied in a natural forest in Iran. Sample disks were taken from each tree to examine wood density and mechanical properties (MOE and MOR) from pith to bark at breast height, 50%, and 75% of total tree height. The analysis of variance (ANOVA) indicated that radial position and height significantly affected all wood properties. The wood density, MOE and MOR were decreased along horizontal position from the pith to the bark and vertical direction from base upwards. Regression analysis showed that modulus of elasticity (MOE) and modulus of rupture (MOR) had a positive correlation with wood density.

• Journal of Magnetics
• /
• v.20 no.4
• /
• pp.371-376
• /
• 2015

Magnetite nanoparticles were synthesized by adding excess ammonium hydroxide to a solution of iron (II) and (III) chlorides. The surfactants of oleic acid and Span 80 were applied in sequence to the magnetic particles as a combined stabilizer, and poly-${\alpha}$-olefin (PAO) 30 or 60 was used as the liquid base with a low or high viscosity, respectively. The ferrofluids were prepared with the concentrations of 200, 300, 400, and 500 mg/mL, and characterized by density, dispersion, magnetization, and viscosity. The density of the fluids increased proportionally to the concentration from 0.98 to 1.27 g/mL and 1.01 to 1.30 g/mL with PAO 30 base and PAO 60 base, and the dispersion stability was 77-95 and 81-74% for the PAO-30 and PAO-60-based fluids, respectively. The observed saturation magnetization values of the PAO-30 and PAO-60-based ferrofluids were 16 to 42 mT and 17 to 41 mT with the concentration increase in the range 200-500 mg/mL, respectively, depending upon the content of magnetic particles in the fluid. The viscosity variation of the PAO-30 and PAO-60-based ferrofluids in the temperature range $20-80^{\circ}C$ was the least with the concentrations of 400 and 300 mg/mL, respectively.