• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.111-120
• /
• 2006

In this paper, a node architecture of WDM metro network for connecting broadband access networks to converge wire/wireless networks. In consideration of the proposed node architecture and network requirements we proposed and evaluated medium access control protocols. We review WDM related technologies of sub-carrier multiplexing and optical components in order to resolve the bottleneck between optical backbone networks md access networks, and a access node architecture sharing common wavelength is introduced. Source-stripping (SS) MAC protocol Is evaluated under the proposed functional node architecture. DS+IS (Destination-Stripping and Source-Stripping) and DS+IS (Destination-Stripping and Intermediate-Stripping) MAC protocols are described to increase the slot-reuse factor which is low on SS MAC protocol. The key function of new MAC protocols regards the optical switch module of proposed node architecture and helps intermediate or source access nodes for dropping slots to destinations of different wavelength group. Thus, slot-reuse factor increases as the MAC protocols reduce the unnecessary ring-rotation of transferred slots. We use a numerical analysis to expect bandwidth efficiency and maximum throughput by slot-reuse factor Throughput network simulation, the verification of throughput, queuing delay, and transmission fairness are compared among MAC protocols.

• Journal of Navigation and Port Research
• /
• v.33 no.10
• /
• pp.691-697
• /
• 2009

Hardware dedicated off-the-shelf maritime differential GPS RSIM lacks the open architecture to meet all the minimum maritime user requirements and to include future GNSS improvements after recapitalization. This paper carries out a study to replace existing hardware dedicated differential GPS RSIM with software differential GPS RSIM in order to make up the weak point of hardware dedicated off-the-shelf maritime differential GPS RSIM. In this paper, the architecture of software RSIM is proposed for maritime DGPS recapitalization. And the feasibility analysis of the proposed software differential GPS RSIM is performed as the first phase to realize the proposed architecture. For the feasibility analysis, the prototype RF module and DSP module are implemented with properties as wide RF bandwidth, high sampling frequency, and high speed transmission interface. This paper shows that the proposed architecture has the possibility of real time operation of software RSIM functionality onto the PC-based platform through the analysis of computation time. Finally, this paper verifies that the L1/L2 dual frequency software differential RSIM designed according to the proposed method satisfies the performance specifications set out in RTCM paper 221-2006-SC104-STD.

• The KIPS Transactions:PartC
• /
• v.12C no.6 s.102
• /
• pp.881-890
• /
• 2005

Over for the past 10 years, the increase in geometric progression for the internet traffic, has allowed the IP protocol framework to be the most important network technology. In addition, the internet service is being developed as a service mode differentiated, aiming to support the new-mode real-time multimedia services such as internet phone, video conference, cyber reality, and internet game, focusing on offering a latest service. These days, aiming to solve the need for broad bandwidth along with guaranteeing QoS, the WDM technology of offering multiple gigabit wavelengths is emerging as the core technology of next-generation optical internet backbone network. In the next-generation optical internet backbone network based on WDM, the QoS framework is one of fore subjects aiming to offer a service of guaranteeing QoS This study analyzes the requirements of performance related to QoS framework in IP Subnet and in WDM optical backbone network, and suggests optical QoS service framework differentiated. in order to guarantee end-to-end QoS through the next-generation optical internet backbone network, using GMPLS control protocol.

• Journal of KIISE:Computer Systems and Theory
• /
• v.35 no.7
• /
• pp.305-317
• /
• 2008

As a mobile computing environment is rapidly changing, increasing user demand for multimedia-over-wireless capabilities on embedded processors places constraints on performance, power, and sire. In this regard, this paper proposes color media instructions (CMI) for single instruction, multiple data (SIMD) parallel processors to meet the computational requirements and cost goals. While existing multimedia extensions store and process 48-bit pixels in a 32-bit register, CMI, which considers that color components are perceptually less significant, supports parallel operations on two-packed compressed 16-bit YCbCr (6 bit Y and 5 bits Cb, Cr) data in a 32-bit datapath processor. This provides greater concurrency and efficiency for YCbCr data processing. Moreover, the ability to reduce data format size reduces system cost. The reduction in data bandwidth also simplifies system design. Experimental results on a representative SIMD parallel processor architecture show that CMI achieves an average speedup of 6.3x over the baseline SIMD parallel processor performance. This is in contrast to MMX (a representative Intel's multimedia extensions), which achieves an average speedup of only 3.7x over the same baseline SIMD architecture. CMI also outperforms MMX in both area efficiency (a 52% increase versus a 13% increase) and energy efficiency (a 50% increase versus an 11% increase). CMI improves the performance and efficiency with a mere 3% increase in the system area and a 5% increase in the system power, while MMX requires a 14% increase in the system area and a 16% increase in the system power.

• Macromolecular Research
• /
• v.10 no.1
• /
• pp.2-12
• /
• 2002

The small-angle X-ray scattering (SAXS) beamline BL4C1 at the 2.5 GeV storage ring of the Pohang Accelerator Laboratory (PAL) has been in its first you of operation since August 2000. During this first stage it could meet the basic requirements of the rapidly growing domestic SAXS user community, which has been carrying out measurements mainly on various polymer systems. The X-ray source is a bending magnet which produces white radiation with a critical energy of 5.5 keV. A synthetic double multilayer monochromator selects quasi-monochromatic radiation with a bandwidth of ca. 1.5%. This relatively low degree of monochromatization is sufficient for most SAXS measurements and allows a considerably higher flux at the sample as compared to monochromators using single crystals. Higher harmonics from the monochromator are rejected by reflection from a flat mirror, and a slit system is installed for collimation. A charge-coupled device (CCD) system, two one-dimensional photodiode arrays (PDA) and imaging plates (IP) are available its detectors. The overall performance of the beamline optics and of the detector systems has been checked using various standard samples. While the CCD and PDA detectors are well-suited for diffraction measurements, they give unsatisfactory data from weakly scattering samples, due to their high intrinsic noise. By using the IP system smooth scattering curves could be obtained in a wide dynamic range. In the second stage, stating from August 2001, the beamline will be upgraded with additional slits, focusing optics and gas-filled proportional detectors.

• The KIPS Transactions:PartC
• /
• v.9C no.1
• /
• pp.73-78
• /
• 2002

In WATM networks, in order to perform dynamic slot allocation required slots of mobile terminals are estimated based on DP (Dynamic Parameter) reflecting characteristics of traffic. In VBR (Variable Bit Rate) traffic, slot allocation is done at MT considering both time-dependent characteristics and QoS (Quality of Service) requirements. In this paper, DPs-buffer state information and buffer state change-are transmitted through in-band signaling. BS (Base Station) performs dynamic slot allocation considering traffic characteristics of each MT (Mobile Terminal), in other words, buffer state information informs the potentiality of 'buffer full state'to BS if MT buffer is over the specific threshold value and buffer state change notifies change in buffer state of incoming cells to MT. If buffer state information is equal to 'low (more than threshold)' and 'abrupt increase' it generates 'buffer full' state cell transmission delay or cell loss might occur. At this time BS should assign additional slots to MT, and then MT consumes cells in its buffer. In simulation, the proposed scheme shows better performance in cell delay and loss than EPSA (Estimation-Prorated Slot Assignment) in-band scheme.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.1
• /
• pp.73-79
• /
• 2020

Modern radar system requires high spectral purity and low phase noise characteristics for very low RCS target detection and high resolution SAR (Synthetic Aperture Radar) image. This paper presents a new X-band high stable frequency synthesizer for high performance radar system, which combines DAS (Direct Analog Synthesizer) and DDS (Direct Digital Synthesizer) techniques, in order to cope with very low phase noise and high frequency agility requirements. This synthesizer offers more than 10% operating bandwidth in X-band frequency and fast agile time lower than 1 usec. Also, the phase noise at 10kHz offset is lower than -136dBc/Hz, which shows an improvement of more than 10dB compared to the current state of art frequency synthesizer. This architecture can be applied to L-band and C-band application as well. This frequency synthesizer is able to used in modern AESA (Active Electronically Scanned Array) radar system and high resolution SAR application.

• KIPS Transactions on Software and Data Engineering
• /
• v.10 no.10
• /
• pp.391-398
• /
• 2021

Since the leased line is a structure that exclusively uses two connected areas for data transmission, a stable quality level and security are ensured, and despite the rapid increase in the number of switched lines, it is a line method that is continuously used a lot in companies. However, because the cost is relatively high, one of the important roles of the network operator in the enterprise is to maintain the optimal state by properly arranging and utilizing the resources of the network leased line. In other words, in order to properly support business service requirements, it is essential to properly manage bandwidth resources of leased lines from the viewpoint of data transmission, and properly predicting and managing leased line usage becomes a key factor. Therefore, in this study, various prediction models were applied and performance was evaluated based on the actual usage rate data of leased lines used in corporate networks. In general, the performance of each prediction was measured and compared by applying the smoothing model and ARIMA model, which are widely used as statistical methods, and the representative models of deep learning based on artificial neural networks, which are being studied a lot these days. In addition, based on the experimental results, we proposed the items to be considered in order for each model to achieve good performance for prediction from the viewpoint of effective operation of leased line resources.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.6
• /
• pp.645-654
• /
• 2021

In this paper, we proposed a protocol to convert 2W telephone analog signals to Ethernet data in a private PSTN 2W tactical voice system. There are several kinds of operational problems in the tactical telephone network where 2W telephone copper lines are installed hundreds of meters away from the PBX in a headquarter site. The reason is that it is difficult to install and maintain the 2W telephone copper cable in severe operational fields and to meet safety and stability operational requirements of the telephone line under lighting and electromagnetic environments. In order to solve these challenging demands, we proposed an efficient method that the 2W analog interface signals between a private PBX system and a 2W telephone is converted to Ethernet messages using the optical Ethernet data communication network already deployed in the tactical weapon system. Thus, it is not necessary to install an additional optic cable for the ethernet telephone line and to maintain the private PSTN 2W telephone network. Also it provides safe and secure telecommunication operation under lightning and electromagnetic environments. This paper presents the conversion protocol from 2W telephone signals over Ethernet interface between PBX systems and 2W telephones, the mutual exchange protocol of ethernet messages between two converters, and the rule to process analog signal interface. Finally, we demonstrate that the proposed technique can provide a feasible solution in the tactical weapon system by analyzing its performance and experimental results such as the bandwidth of 2W telephone ethernet network and the transmission latency of voice signal, and the stability of optic ethernet voice network along with the ethernet data network.

• Nuclear Engineering and Technology
• /
• v.56 no.7
• /
• pp.2799-2805
• /
• 2024

Energy-resolved neutron imaging is an effective way to investigate the internal structure and residual stress of materials. Different sample sizes have varying requirements for the detector's imaging field of view (FOV) and spatial resolution. Therefore, a dual-mode energy-resolved neutron imaging detector was developed, which mainly consisted of a neutron scintillator screen, a mirror, imaging lenses, and a time-stamping optical fast camera. This detector could operate in a large FOV mode or a high spatial resolution mode. To evaluate the performance of the detector, the neutron wavelength spectra and the multiple spatial resolution tests were conducted at CSNS. The results demonstrated that the detector accurately measured the neutron wavelength spectra selected by a bandwidth chopper. The best spatial resolution was about 20 ㎛ in high spatial resolution mode after event reconstruction, and a FOV of 45.0 mm × 45.0 mm was obtained in large FOV mode. The feasibility was validated to change the spatial resolution and FOV by replacing the scintillator screen and adjusting the lens magnification.