• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.2
• /
• pp.327-333
• /
• 2003

Most of shape defects in steel strip are originated from the structure of rolling mill itself. For instance, strip crown occurs when the work roll is deformed by the bending moment induced on roll chocks. To get rids of the shape defects, it is necessary to increase the stiffness of rolling mill. The structure change of back-up roll is one of alternative ways to increase the mill stiffness without facility revamping from 4 high mill to 6 high mill. In this research work, the new back-up roll was developed and can be used in any type of 4 high mill to reduce the strip shape defects. The developed back-up roll consists of sleeve, arbor and phase angle adjusting system for arbor. The circumference of arbor is specially machined to adapt the strip width change during rolling. The experimental cold rolling test was done to prove the effectiveness of newly developed back-up roll. The experimental rolling results show that the new back-up roll has more powerful performance in reducing the shape defects than conventional back-up roll. It was also found that the new back-up roll has higher stability for shape control. In addition to, the only sleeve surface needs to be reground and changed in most cases, so that the maintenance cost can be greatly reduced.

• Journal of the Ergonomics Society of Korea
• /
• v.28 no.2
• /
• pp.35-55
• /
• 2009

The purpose of this study was to analyze the somatotypes of women in the early 20's, which were likely to deform due to bad posture in growth period. Accordingly, bodies of women aged 20 to 24, whose growth stopped, were measured directly and indirectly, and factors related to body shapes were extracted, body shapes were categorized based on the data, and the characteristics of each body shape were analyzed. As a result, 10 factors related to body shapes were extracted in the factor analysis, and body shapes were categorized into 6 types. Type 1 was the volume of body that was big and the longest; and the general frame was large. The straight body shape with small back protrusion; the shoulder is relatively thick and the width of the shoulder was normal. Type 2 was the volume of body that was the biggest and the upper body was the longest; the general frame was of average height. The forward body shape with the back flat; the shoulder was very thick, wide, and serious leaning forward. Type 3 was a body that was thin and the shortest. The sway-back body shape with big curvature at the back; the shoulder was thin, narrow, and straight. Type 4 was a body that was short stature, and the general frame was of average build. The forward body shape with the most serious back protrusion; the shoulder was normally thick, narrow, and straight. Type 5 was a group with small body, and the lower body and general frame are long. The sway-back body shape with protrusion at the upper shoulder and the sides leaning backward; the shoulder was thin, wide, and leaning forward. Type 6 was a thin and short body; and the general frame was small. The lean-back body shape with the smallest back protrusion and leaning backward; the shoulder was thin, narrow, and leaning backward. Characteristics of the classified body shapes can be used in producing ready-made clothes, and it is hoped that there will be follow-up studies on clothing pattern design and production based on this result.

• Korean Journal of Human Ecology
• /
• v.23 no.6
• /
• pp.1191-1204
• /
• 2014

Even though a Han-bok, or traditional Korean costume, should be inherited since it is invaluable part of our culture, research on Han-bok is scarce. Since the development of a Jeogori pattern, the upper garment of Korean traditional clothes, is done mostly based on the chest size, the design does not completely consider on wearer's body shape. Moreover, unless made by an expert, trial and error is almost always necessary to improve the fit of the clothes. In this research, a Jeogori pattern was suggested that improves the fit based on the shape of the upper back(straight or bent) of a female in her late 20s who often wears a Han-bok and is comfortable when moving. Using a 3D virtual clothing system, the optimum pattern was selected based on the body shape. The final selection was made, and each subjects tried the garment on to evaluate the comfort when moving, along with its appearance, based on a seven point Likert scale. As a result, for a straight body shape, the optimum ease for the front bust width was 2.5cm, and that for the back bust width was 2.0cm. The optimum center back dart was 1.0cm. The optimum Geodae width was 7.6cm, and the optimum back Geodae point was 2.0cm. For the bent body shape, the optimum ease for the front and back bust was 2.0cm. The optimum Geodae width was 8.4cm, and the optimum back Geodae point was 1.5cm. Furthermore, if the Hwajang slope was set at half of the vertical distance between the laterals of the neck and shoulder, a fitted silhouette appeared, which is preferred nowadays. In the appearance evaluation, the final pattern designed in this research received higher scores than the original design(straight; p<.001, bent; p<.05). The results of the evaluation of the comfort when moving also showed higher scores for the final pattern that was designed.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.792-795
• /
• 1996

In TIG welding of pipe, back bead size monitoring is important for weld quality assurance. Many researches have been performed on estimation of the back bead size by heat conduction analysis. However numerical conduction model based on many uncertain thermal parameters causes remarkable errors and thermomechanical phenomena in molten pool can not be considered. In this paper, filler wire feeding force in addition to weld current, wire feedrate, torch travel speed and orbital position angle is monitored to estimate back bead size in orbital TIG welding. Monitored welding process variables are fed into an artificial neural network estimator which has been trained with the monitored process variables (input patterns) and actual back bead size (output patterns). Experimental verification of the proposed estimation method was performed. The predicted results are in a good agreement with the actual back bead shape. The results are quite promising in that estimation of invisible back bead shape can be achieved by analyzing the welding parameters without any conventional NDT of welds.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.911-914
• /
• 2011

Detecting Hand Region is essencial technology to providing User based interface and many research has been continue. In this paper will propose Hand Region Detection method by using HSV space based on Back Projection and Hand Shape Recognition using Hu Moment. By using Back Projection, I updated reliability on Hand Region Detection by Back Projection method and, Confirmed Hand Shape could be recognized through Hu moment.

• Transactions of Materials Processing
• /
• v.30 no.2
• /
• pp.69-73
• /
• 2021

This paper addresses the product shape modification for spring-back reduction in the sheet metal forming process of the cabin sunroof which is applied to the construction equipment. Initially, the anisotropic material properties are measured in order to calculate the degree of spring-back by the numerical simulation of the sheet metal forming process. To reduce the spring-back of the stamped part, several design modifications are suggested according to the geometrical bead arrangement on the planar region. The degrees of spring-back are confirmed for various product designs with different use of the geometrical bead. Finally, the spring-back improvement was validated by manufacturing the tryout product with the modified die set for the optimized product shape.

• The Research Journal of the Costume Culture
• /
• v.28 no.1
• /
• pp.1-14
• /
• 2020

This study is based on a representative body shape drawn from previous studies that classify adult male torso shapes. In this study, a design method is proposed by developing a tight-fit pattern that can be easily developed into various items and designs using the body surface development figure. This is obtained by converting the 3D body shape of the model representing the representative body shape. The specific design method was conducted as follows. Actual measurement values were used for waist back length, waist-to-hip length, shoulder length. The scye depth was determined as C/4-1.7 cm, and the front and back Interscye was set at (1/2 × actual measurements)-0.2 cm. The front-back neck breadth was set to (1/5 × base neck circumference)-1.3 cm and (1/5 × base neck circumference) cm. The front-back neck depth was set to (1/5 × base neck circumference)-1.2 cm and 3.5 cm. Front chest circumference was C/4-1 (front-back difference)cm; (1/4 × back chest circumference) was C/4 + 1 (front-back difference) + 0.3 (dart amount) cm. Front waist circumference was W/4-0.2 (front-back difference) + 2.2 (dart amount) cm; back waist circumference was W/4 + 0.2 (front-back difference) + 2.5 (dartamount) cm; front hip circumference was H/4 + 0.2 (ease) + 0.2 (front-back difference) cm; and back hip circumference was H/4 + 0.2 (ease)-0.2 (front-back difference) cm; Front droop was 1.6 cm. The newly developed tight-fit pattern is expected to be of great use as a basis for garment construction.

• Korean Journal of Human Ecology
• /
• v.23 no.5
• /
• pp.891-904
• /
• 2014

The objective of this study is to classify somatotypes of back-surface shape of women in their late 20s by using 3D body scan data(Size Korea 2010) in order to improve fitness of Hanbok Jeogori. The results were as follows: 1. According to the in-depth survey of the experienced expert's interview, most problems related to the fit were caused by the back area of Jeogori. 2. The result of factor analysis indicated that 6 factors were extracted and those factors comprised 82.85% of total variance. 3. According to the cluster analysis, back somatotypes of women in their late 20s were categorized by two types : straight type(54.1%) and bending type(46.9%). The results could be used as the Hanbok Jeogori to improve the fitness of back-surface shape.

• Journal of the Korean Society of Costume
• /
• v.49
• /
• pp.25-48
• /
• 1999

The purpose of this study is to offer fundamental data for classification of somatotype for boys of elementary school age. The subject were 458 elementary school boys aged from 7 to 12 living in Pusan, Data were collected by 57 anthropometric and 11 photographic measurements and analyzed by factor analysis according to SAS package 1. Through the factor analysis by each period of school ages 6-7 factor were obtained in upper half and they are as followings: 1) Factor 1 is horizontal size of upper half in every period 2) Factor 2 is vertical size of upper half in every period 3) Factor 3 is shoulder shape in the first period and length of upper half in the middle and latter period 4) Facto 4 sis length of upper half in the first period and shoulder shape in the middle and latter period 5) Factor 5 is angle shape of the breast and back in the first period angle shape of the lower breast and back in the middle of period and angle shape of the upper breast and back in the latter of period 6) Factor 6 is angle of shoulder in the first period angle shape of the upper breast and back in the middle of period and angle shape of the lower breast and back in the latter of period 7)Factor 7 is angle of shoulder in the latter of period 2. Through the factor analysis by each period of school ages 5-6 factor were obtained in lower half and they are as followings: 1) factor 1 is horizontal size of upper half in every period 2) Factor 2 is vertical size of upper half in every period 3) Pactor 3 is angle shape of the belly and upper buttock in the first period and length of lower half in the middle and latter period 5) Factor 5 is angle shape of the lower buttock in the first period angle shape of the upper belly and buttock in the middle of period and angle of the side posture in the latter of period 6) Factor 6 is angle shape of the lower buttock in the middle of period and angle shape of the lower belly and buttock

• Journal of the Korean Society of Costume
• /
• v.30
• /
• pp.201-210
• /
• 1996

The perpose of this study is to compare and to analyze the characters of the shape of up-per arm and armscye line between young and aged women. The subjects were measured with the Mar-tin's anthropometer and with free curve ruler. 10 items in the shape of upper arm were measured and 16 items in the shape of armscye line measured indirectly based on the measured shape taken from the subjects with free curve ruler and both date were analyzed. Mean standard deviation f-test factor analysis were performed for the statistical analysis of the date. The main results were as follows: 1) The shape of the upper arm is long and narrow in youg women compared with aged. 2) The length of the axilla of the aged women were longer than that of young women. 3) There are significant differences young and aged women on the shape of armscye line. THe length of from the front point of axilla to shoulder point width and depth of the shape of the armscye line length of axilla of aged women were longer than that of young. but the length of from the back point of axilla to shoulder point of yyoung women was longer than aged. 4.) The front point of axilla was existed lower than back point of axilla in aged women while front point of axilla was existed higher than the back point in young. 5) Through the factor analysis two factors were obtained from the shape of the upper arm and five factors from the shape on armmscye line in both groups. Factor compornents in the shape of the up per arm were length width and girth of that and in the shape of the armscye line were width and length of upper and lower back and front part of the shape of the armscye line depth of the axilla. he items in the same factor were resemble each other between two groups.