• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.1-8
• /
• 2016

Dead time is typically incorporated in voltage source inverter systems to prevent short circuit cases. However, dead time causes an error between the output voltage and reference voltage. Hence, voltage equation-based algorithms, such as motor parameter estimation and back electromotive force (EMF)-based sensorless algorithms, are prone to estimation errors. Several dead-time compensation methods have been developed to reduce output voltage errors. However, voltage errors are still common in zero current crossing areas, and an effect of the error is much worse in a low speed region. Therefore, employing voltage equation-based algorithms in low speed regions is difficult. This study analyzes the conventional dead-time compensation method and output voltage errors in low speed operation areas. A current shaping method that can reduce output voltage errors is also proposed. Experimental results prove that the proposed method reduces voltage errors and improves the accuracy of the parameter estimation method and the performance of the back EMF-based sensorless algorithm.

• 대한안전경영과학회지
• /
• 제17권3호
• /
• pp.363-370
• /
• 2015

In this paper, the control technique of the stepping motor using back electromotive force(B-EMF) without encoder is investigated. The stepping motor generally uses the rotary encoder to detect the rotor position. Since this method increases the cost and the motor configuration size, the new closed-loop control method applied for the B-EMF was implemented by using current detect circuit, AD-converter, and micro controller unit(MCU). The control loop of stepping motor became very simplified. The current change of stepping motor measured by the amplifier was measured and analyzed, when the missing step is occurred. Based on the data from current feedback, position errors were compensated and confirmed by using AD-converter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.893-894
• /
• 2006

This paper presents a design and analysis solutions for the general class and control parameter estimation of slotted iron-cored Permanent Magnet Linear Synchronous Motor with Halbach magnetization stator and 3-phase winding mover. In our design and analysis, stator consisting of permanent magnets and slotted iron-cored coil mover are treated in a uniform way via magnetic vector potential. For one such motor structure, we give analytical formulas for its magnetic field, back electromotive force and trust force. Moreover, the detent force are calculated by the relative permeance function. In good agreement with the estimated values from the analyses, the experimental results and Finite Element Method (FEM) confirm the validity of the design and analysis framework.

• Journal of Magnetics
• /
• 제19권1호
• /
• pp.84-89
• /
• 2014

This paper presents an analytical prediction and experimental verification of the electromagnetic performance of a parallel magnetized surface-mounted permanent magnet (SPM) motor having a fractional number of slots per pole combination. On the basis of a two-dimensional (2-D) polar coordinate system and a magnetic vector potential, analytical solutions for flux density produced by the permanent magnets (PMs) and stator windings are derived. Then, analytical solutions for back-electromotive force (emf) and electromagnetic torque are derived from these field solutions. The analytical results are thoroughly validated with 2-D nonlinear finite element (FE) analysis results. Finally, the experimental back-emf and electromagnetic torque measurements are presented to test the validity of the analysis.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권1호
• /
• pp.1-7
• /
• 2004

This paper presents a sensorless control strategy of a PMSM(Permanent Magnet Sycchoronous Motor). This method is very simple to compute the position angle of a rotor. A principle and a practical solution are described. A sensorless control algorithm is proposed to remove a mechanical position sensor. The theory is based on the superposition principle. The state equation of a motor is divided into two conditions: one is the state equation of exciting voltage and phase current in a constraint, the other is the state equation of back EMF(Electromotive Force) and phase current in a short circuit. Based on the analysis, short circuit current by back EMF is computed and then the information of position angle is calculated. The proposed method is verified by experimental results.

• Journal of Magnetics
• /
• 제21권1호
• /
• pp.78-82
• /
• 2016

Cogging torque will affect the performance of a permanent magnet Brushless DC Motor (BLDCM), thus the reduction of cogging torque is key for BLDCM optimization. In this paper, the phase shifting of cogging torque for a fractional-slot concentrated winding BLDCM is analyzed using the Maxwell tensor method. Moreover, a 9-slot 10-pole concentrated winding BLDCM driven by ideal square waveform is studied with the finite element method (FEM). An effective method to reduce the cogging torque is obtained by adjusting the slot opening. In addition, the influences of different slot openings on back electromotive force (back-EMF), air gap flux density and flux linkage are investigated and experimentally validated using the prototype BLDCM.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 B
• /
• pp.1108-1110
• /
• 2000

The BLDCM(Brushless DC motor) has been the Trapezoidal Back Electromotive Force(EMF) due to a surface magnet rotor with nonlinear distribution and full-pitch windings. Theoretically, it should be fed with rectangular phase current in order to minimize torque ripple. But, because voltage source inverter drives BLDCM, perfectly rectangular phase currents are not available. Now in this paper, using fourier series coefficients, calculating the coefficients of harmonic current within available orders and each harmonic component are controlled on stationary frame. Only using four switches, low cost and small size drive can be made and proposed method will be more useful in industrial. Simulation and experimental results prove the validity of the proposed method.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권2호
• /
• pp.134-140
• /
• 2013

This paper proposes a new design of rotor shape of Interior Permanent Magnet Synchronous Motor (IPMSM) used for agricultural electric vehicle (AEV). The distribution of the residual magnetic flux density at the air gap is modified by rotor surface shape and V-type magnet angle. As a result, cogging torque and physical characteristic have been improved, and back electromotive force (back-EMF) of the suggested model has been improved to be closest to sine wave form compared to initial model. The validity of the proposed rotor shape optimization is confirmed by the manufactured IPM rotor core and measured the performance of the cogging torque.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.72-74
• /
• 2003

This paper presents a design and analysis solutions for the general class of iron-cored permanent magnet linear synchronous motor with Halbach (PMLSM). In our design and analysis, rotor consisting of permanent magnets rotor and slot less iron-cored coil stator are treated in a uniform way via vector potential. For one such motor structure, we give analytical formulas for its magnetic field, back electromotive force, inductance of winding coil, and trust force. We also provide performance comparisons of three types according to iron-cored and PM array.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1174-1176
• /
• 2005

The permanent magnet(PM) overhang effect has been generally used to enhance the linkage flux in the motor. In this paper, we quantitatively investigate the PM overhang effect in the new type axial flux permanent magnet(AFPM) motor with a double-sided airgap. The motor performances such as linkage flux, back electromotive force(EMF), magnetic force, etc. were analyzed according to the variation of the overhang angle. From the results, we can select the proper overhang angle of PM which improves the performance of the AFPM motor.