• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.4
• /
• pp.3980-3990
• /
• 1975

This study was carried out to develop a method of grain drying ststem that can be done by forcing the heated-air directly into the grains within the sack. The air duct was pushed into the central position of the grain-deposited sack and the heated-air was forced to flow in the radial direction. The system is referred here as the unit sack drying system. At a first step of this study, an air flow resistance tester was constructed to measure the resistance of air flow to grains in cooperated with some different sack materials, the sack materials, the tested were rice-straw bag, sack of polyethylene film, and jute sack In addition, unit sack drying system was constructed to investigate the drying characteristics of the dryer. on this dryer, two kind of terminal air ducts were attached and tested to examine its effects on uniform drying, and also, aseries of drying test was performed to trace the effect of increasing air flow rate on uniform drying. The results are as follows: 1) Resistance of air flow for each sack material was increased almost proportional to the increasing rate of air flow. Experimental data showed little significant differences of the air flow resistance among the materials. 2) From the comparison with air flow resistance of sack material and that of roughrice, it was indicated that airflow resistance of sack material was much higher than that of rice rough Therefore, in the unit sack drying sysle in which air flow is destined to face the sach material after leaving the grain, it was suggested that air flow would be inuniform to each part of grain within sack because of much higher air flow resistance of sack material than that of grain, and the fact would results inuniform grain drying. 3) Drying test on the unit sack drying system in cooperated with different type of terminal air ducts showed that high speed air is better for uniform drying than in high pressure. with the drying system which was assembled with the air ducts delivering higher speed air, there also involved a problem of significant inuniform drying. Therefore, any means to improve the inuniform drying should be undertaken for practical use. 4) A series of drying test with in creasing air flow rate resulted that increasing air flow rate in the unitsack drying system gave little effect on uniform drying, therefore, it is recommened to change its drying system for drying grain uniformly.

• Design & Manufacturing
• /
• v.14 no.1
• /
• pp.8-14
• /
• 2020

In general, auto parts production assembly line is assembled and produced by automatic mounting by an automated robot. In such a production site, quality problems such as misalignment of parts (doors, trunks, roofs, etc.) to be assembled with the vehicle body or collision between assembly robots and components are often caused. In order to solve such a problem, the quality of parts is manually inspected by using mechanical jig devices outside the automated production line. Automotive inspection technology is the most commonly used field of vision, which includes surface inspection such as mounting hole spacing and defect detection, body panel dents and bends. It is used for guiding, providing location information to the robot controller to adjust the robot's path to improve process productivity and manufacturing flexibility. The most difficult weighing and measuring technology is to calibrate the surface analysis and position and characteristics between parts by storing images of the part to be measured that enters the camera's field of view mounted on the side or top of the part. The problem of the machine vision device applied to the automobile production line is that the lighting conditions inside the factory are severely changed due to various weather changes such as morning-evening, rainy days and sunny days through the exterior window of the assembly production plant. In addition, since the material of the vehicle body parts is a steel sheet, the reflection of light is very severe, which causes a problem in that the quality of the captured image is greatly changed even with a small light change. In this study, the distance between the car body and the door part and the door are acquired by the measuring device combining the laser slit light source and the LED pattern light source. The result is transferred to the joint robot for assembling parts at the optimum position between parts, and the assembly is done at the optimal position by changing the angle and step.

• Journal of Food Hygiene and Safety
• /
• v.15 no.2
• /
• pp.114-121
• /
• 2000

A study was carried out to establish a detection method for irradiated black and white pepper. Samples were packed in polyethylene bags and irradiated with 2.5, 5, 7.5, 10 and 15 kGy using a Co-60 irradiator. The samples were suspended in water, and alkalized with sodium hydroxide solution. Apparent viscosity was determined after heat gelatinization using a Brookfield DV-III rotation viscometer at 30。C with 30, 60, 90, 120, 150, 180, and 210 rpm. Means and standard deviations of the viscosities of all samples decreased by increasing the stirring speeds. The viscosities increased in all samples by increasing the concentration. Regression expressions and coefficients of viscosity which decreased with increasing irradiation dose of 10% and 13% black pepper, and 7% and 10% white pepper were 0.9531 (y=-131.29x+1,769.0), 0.9725 (y=-351.33x+4,036.0), 0.9731 (y=2,208.0e${^-0.3546X}$), and 0.9959 (y=5,116.0e${^-0.2887X}$), respectively, at 120 rpm. This trend was similar fur all stirring speeds. These results suggest that the detection of irradiated black and white pepper at various doses is possible by the viscometric method.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.4
• /
• pp.534-541
• /
• 2009

The aim of this study was to evaluate the effects of gamma irradiation (${\gamma}$-irradiation) at doses of 15, 30 and 45 kGy on chemical composition, anti-nutritional factors, ruminal dry matter (DM) and crude protein (CP) degradibility, in vitro CP digestibility and to monitor the fate of true proteins of full-fat soybean (SB) in the rumen. Nylon bags of untreated or ${\gamma}$-irradiated SB were suspended in the rumens of three ruminally-fistulated bulls for up to 48 h and resulting data were fitted to a nonlinear degradation model to calculate degradation parameters of DM and CP. Proteins of untreated and treated SB bag residues were fractionated by sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE). Digestibility of rumen undegraded CP was estimated using the three-step in vitro procedure. The chemical composition of raw and irradiated soybeans was similar. Results showed that phytic acid in ${\gamma}$-irradiated SB at dose of 30 kGy was eliminated completely. The trypsin inhibitor activity of 15, 30 and 45 kGy ${\gamma}$-irradiated SB was decreased (p<0.01) by 18.4, 55.5 and 63.5%, respectively. From in sacco results, ${\gamma}$-irradiation decreased (p<0.05) the washout fractions of DM and CP at doses of 30 and 45 kGy, but increased (p<0.05) the potentially degradable fractions. Gamma irradiation at doses of 15, 30 and 45 kGy decreased (p<0.05) effective degradability of CP at a rumen outflow rate of 0.05 $h^{-1}$ by 4.4, 14.4 and 26.5%, respectively. On the contrary, digestibility of ruminally undegraded CP of irradiated SB at doses of 30 and 45 kGy was improved (p<0.05) by 12 and 28%, respectively. Electrophoretic analysis of untreated soybean proteins incubated in the rumen revealed that ${\beta}$-conglycinin subunits had disappeared at 2 h of incubation time, whereas the subunits of glycinin were more resistant to degradation until 16 h of incubation. From the SDS-PAGE patterns, acidic subunits of 15, 30 and 45 kGy ${\gamma}$-irradiated SB disappeared after 8, 8 and 16 h of incubation, respectively, while the basic subunits of glycinin were not degraded completely until 24, 48 and 48 h of incubation, respectively. It was concluded that ${\gamma}$-irradiated soybean proteins at doses higher than 15 kGy could be effectively protected from ruminal degradation.

• Investigative Magnetic Resonance Imaging
• /
• v.17 no.1
• /
• pp.8-18
• /
• 2013

Purpose : The purpose of this study was to find and categorize the various magnetic resonance imaging (MRI) findings of spinal metastases that correlate with the type of primary cancer. Materials and Methods: We retrospectively reviewed gadolinium-enhanced magnetic resonance images of 30 patients with 169 spinal metastatic lesions from lung cancer (n = 56), breast cancer (n = 29), colorectal cancer (n = 20), hepatocellular carcinoma (HCC) (n = 17), and stomach cancer (n = 47). The size, location, extent of invasion, signal intensity, margin, enhancement pattern, and osteoblastic or osteolytic characteristics of each metastatic tumor were analyzed. Results: The metastatic lesions from HCC were larger than those from the other primary tumors (P < 0.05) except for colorectal cancer (P = 0.268). Well-defined metastatic tumor margins were more frequently seen in lung cancer and breast cancer (P < 0.01). All but HCC showed a tendency to invade the vertebral body rather than the posterior elements (P < 0.02). Colorectal cancer and HCC showed a tendency toward extraosseous invasion without statistical significance. HCC showed a characteristic enhancement pattern of 'worms-in-a-bag'. Rim enhancement with a sclerotic center was only seen in spinal metastases from stomach cancer. Conclusion: Despite many overlapping imaging features, spinal metastases of various primary tumors display some characteristic MRI findings that can help identify the primary cancer.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.11
• /
• pp.1527-1533
• /
• 2001

Garole is a prolific, rare, less known and small size Indian sheep breed found in low and humid Sunderban region of West Bengal. Although information on stored Garole ram liquid semen upto 24 h is available, but there is a need to further investigate the short-term and long-term preservability of Garole ram semen for extensive utilization of this valuable germplasm by artificial insemination. The aim of the present study was to apply computer-assisted sperm analysis technique for assessing the motion characteristics of Garole ram semen stored (i) in liquid state at refrigeration temperature for short-term preservation upto 48 h and (ii) in frozen state at $-196^{\circ}C$ for long-term preservation after packaging in mini straws. Short-term preservation had a significant effect on motility (p<0.01) as the motility progressively decreased from 90.1% at 0 h to 85.5% and 73.2% after 24 and 48 h of storage, respectively. Although the decline in rapid moving sperms was also significant (p<0.01) on storage but the decrease was more pronounced at 48 h as compared to 24 h of storage period. Storage of chilled semen had also a significant effect on % linearity (p<0.05), % straightness (p<0.01), sperm velocities (p<0.01), amplitude of lateral head displacement (p<0.01) and beat frequency (pO.Ol) of spermatozoa. The replication had a significant effect for all the variables except average path and straight line velocity. However, the interactions of short-term storage and replication were non-significant for most of the variables except % of medium moving sperms, sperm velocities and beat frequency. On long-term preservation of Garole ram spermatozoa under controlled conditions the mean post-thaw recovery of 70.4 and 71.4% motile spermatozoa was achieved having 48.8 and 48.9% of rapidly motile spermatozoa, respectively in both the replicates. The effect of replication on cryopreservation was significant (p<0.05) on amplitude of lateral head displacement and beat frequency, but there was no significant effect on motility, rapidly motile spermatozoa, linearity, straightness and sperm velocities of frozen-thawed spermatozoa. It can be concluded from these results that an average 70% motility can be achieved on storage of Garole ram semen in chilled liquid state upto 48 h or in liquid nitrogen after freezing under controlled conditions in straws. However, further studies are required to evaluate the fertility of short-term and long-term preserved Garole ram semen for extensive use of this prolific sheep breed.

• Environmental and Resource Economics Review
• /
• v.24 no.4
• /
• pp.747-761
• /
• 2015

This paper investigates the impact of an increase in unit price of solid waste collection on demand for alternative solid waste disposal types. I control for other variables affecting the demand and employ both community and time fixed effects models in the estimation of each reduced-form demand functions. Estimation results show that an increase in unit price reduces the demand for garbage bag collection services of non-food solid wastes while it increases the demand for food wastes and source-separated recyclables. These results imply that reduction in the demand for non-food solid wastes collection is mainly achieved by increasing the amount of recyclables and food wastes collected. However, it appears that an increase in unit price increases the total amount of solid wastes generated. This suggests that price incentive effects are offset by the decrease in source-reduction efforts because of feedback effects resulting from the increase in recycling, food waste separation, and illegal disposal of wastes.

• The Korean Journal of Mycology
• /
• v.48 no.2
• /
• pp.95-102
• /
• 2020

This study was carried out to develop a new method of cultivation of 'Hwadam' a new variety of Lentinula edodes, to improve fruiting body productivity and reduce labor. To determine the optimum filter number for box cultivation, L. edodes were assessed for their cultural characteristics and mushroom yield. During spawn running of L. edodes in the box, the temperature gradually increased to the highest value of 25.8℃, 23.7℃, and 23.0℃ on day 18 for the four filter, two filter, and no treatment groups, respectively. Oxygen concentration displayed an opposite trend to carbon dioxide concentration, reaching the lowest value on day 21. The oxygen concentration progressively increased as more filters were used (5.4%, 8.2%, and 8.9% treatment with no, two, and four filters, respectively. Growth of L, edodes in the box resulted in the highest yield (2,228 g/7kg substrate) and biological efficiency (70.7%) using four filters. The biological efficiency of the four filter treatment was 29.4% higher compared to bag cultivation (41.3%). Further studies are necessary to verify stable productivity of fruiting bodies through repeated cultivation.

• Food Science and Preservation
• /
• v.13 no.1
• /
• pp.8-12
• /
• 2006

The effects of packaging treatments with either low density polyethylene (LDPE) or polypropylene (PP) films on the quality of leaf lettuce were evaluated. It was also stored within a plastic bag (LDPE and PP films) with 4 pelf orated holes (6mm diameter). Changes in weight loss, color difference, anthocyanin, chlorophyll, water content, and general appearance (shape of lettuce) ware investigated Total weight of leaf lettuce packaged within non-pelf orated films decreased slowly over the storage periods at 5 and $20^{\circ}C$. The weight loss of leaf lettuce showed no significant difference between non-pelf orated and perforated films at $20^{\circ}C$. General appearance in leaf lettuce stored at $20^{\circ}C$ was not significantly affected by packaging treatments with LDPE and PP films. The shelf life of non-packaged leaf lettuce at $5^{\circ}C$ was 8 days, whereas packaging treatments with LDPE and PP films showed freshness in leaf lettuce for 30 days of storage. Total chlorophyll and water contents of leaf lettuce packaged within pelf orated and non-pelf orated films decreased gradually during storage. However, no remarkable changes in color difference, levels of chlorophyll and anthocyanin, and water contents were observed in leaf lettuce packaged within perforated and non-pelf orated films. In this experiment, leaf lettuce packaged within LDPE or PP films without any punching holes at $5^{\circ}C$ was the most desirable for extending the quality. These results suggest that non-pelf orated packaging treatment in combination with low storage temperature could be effective in prolonging the shelf life of leaf lettuce

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.22 no.3
• /
• pp.200-208
• /
• 2012

Objectives: This study investigated the performance of three separate units of a portable photoionization detector (PID, ppb-RAE 3000) for measuring volatile organic compounds (VOCs) in a laboratory. Methods: A laboratory evaluation of the accuracy, precision, and inter-instrumental variance of three separate units of a portable PID (ppb-RAE 3000) was performed. The evaluation was based on the preparation of a test air sample of known toluene or ethylacetate concentration in a Tedlar$^{(R)}$ bag. The test air sample was monitored and data were logged consecutively by the three PIDs. A certified gas of 50 ppm toluene was also monitored during the test to ensure the reliability of the generated test air sample. Four different concentrations ranging from 0.1 to 2 TLV were used and a series of five measurements for each concentration level was performed. The accuracy was evaluated using National Institute for Occupational Safety and Health (NIOSH) criteria. Results: The results from the oldest ppb-RAE3000 unit among the three test units generally fell outside the NIOSH recommended accuracy criteria of ${\pm}25%$, whereas the other two units produced results which were acceptable at, or greater than, 25 ppm of toluene, or 0.5 TLV. These units also met the NIOSH criteria for some ethylacetate measurements but the results were not consistent. Conclusions: Considering the inconsistent performance of these ppb-RAE 3000 units, this device may not be appropriate for use as an alternative to the standard measurement methods. However, it can serve good survey instruments to identify exposure sources or concentration profiles. For all applications, the ppb-RAE 3000 should be used with frequent calibration checks, additional validation using a reference material, and careful maintenance.