• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.922-926
• /
• 2002

In this paper, in order to investigate the catalytic effect of the sludge exhausted from waterworks as heating temperature for NOx removal, we measure NO, $NO_2$ concentration as increasing temperature of sludge pellets and applying high voltage to sludge pellets in a quartz-glass reactor at the same time. NO initial concentration is 100ppm balanced with air gas in a mixing chamber. The gas flow is 5[l/min] and the heating temperature of sludge pellets in a quartz-glass reactor is adjusted from $200[^{\circ}C]$ $400[^{\circ}C]$ to investigate the effect of sludge pellets for removal NOx$(NO+NO_2)$ as increasing temperature. $BaTiO_3$ pellets is filled in a packed-bed reactor for corona discharge to measure how much NOx$(NO+NO_2)$ is removed after generating $NO_2$ from the packed-bed reactor. AC[60Hz] voltage is supplied to the reactor for discharge. In the result, $NO_2$ concentration is decreased by sludge pellets without heating temperature for sludge pellets in case of sludge pellets done heat treatment, however NO concentration is almost the same to be compared NO initial concentration. As increasing heating temperature for sludge pellets, $NO_2$ adsorbed on the sludge surface done heat treatment is converted to NO by the thermal energy, so NO concentration is extremely increased by reduction decomposition of $NO_2$. Finally, We think the sludge is possible to use for reduction catalysts, however we need to study more about the possibility and endurance of sludge as catalysts for NOx removal.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.363-368
• /
• 1999

Y-5a-Cu-O superconductors were prepared by TSMG (Top-Seeded Melt Growth) process with multiseeding technique. By using several seeds at the same time, large samples could be fabricated in a short time with simple heat treatment. However, the samples fabricated by normal multiseeding technique show the rapid decrease of trapped magnetic field value across the grain boundaries because of the residual liquid layer. To remove the residual liquid layer, modified multiseeding was newly suggested. The individual grains were combined as single domain, and did not show deterioration of magnetic property at the boundary. The formation mechanism of a well-combined domain by multiseeding technique was discussed.

• YAKHAK HOEJI
• /
• v.39 no.6
• /
• pp.636-644
• /
• 1995

Comparison of bioavailabflity (BA) of three brands of ranitidine (RT) tablets has been studied m rats. The purpose of this study was to characterize the pharniacolunetics of RT tablets in the rat and to coinpare phannacolunetic parameters of three brands of RT tablets. In addition, it was investigated whether plasma RT concentrations m humans can be predicted from pharmacokinetic parameters obtained in rats. RT was administered intravenously in dose of RT.HCI 10mg/kg and orally in dose of RT.HCI 50mg/kg as solution or crushed sample of thablets. Plasma RT concentrations were determned by HPLC. Plasma RT concentrations as a function of time were fitted to two compartment model. Plasma RT concentrations declined with a terminal half life ($t_{{1}/2{\betha}}$) of 40.9 min. The plasma RT concentration-time curve showed two peak plasma concentrations following an oral administration of solution or crushed sample in rats like humans. No significant difference among pharmacokinetic parameters was observed except $T_{max2}$ (p<0.05). The BA for crushed sample A, B and C were found to be 54.6 40.7 and 40.0%, respectively. Equivalence of $C_{max1}$ and $T_{max2}$ were guaranteed in this study. However, it was concluded that three brands of RT tablets are bioequivalent, taking the following characteristics of RT into consideration;(1) rapid onset of the effect is not required, (2) $C_{max1}$ and $T_{max2}$ do not seem to influence the effectiveness of the drug during a long-term treatment by the usual administration of twice a day. Results from this study were combined with plarmacokinetic data for RT in dogs and humans to develop a basis for interspecies scale-up of the disposition characteristics of the drug. there were similarities in the general disposition of the drug. Allometric relationships were sought between pharmacokinetic parameters nd species body weight. Significant interspecies correlations were found for total body clearance($Cl_{t}$) and steady state volume of distribution ($Bd_{ss}$). Thus, plasma RT concentrations in humans can be predicted from pharmacokinetic parameters obtained in rats.

• Journal of Korea Foundry Society
• /
• v.41 no.6
• /
• pp.535-542
• /
• 2021

In this study, to improve the interfacial bond strength of cast iron-aluminum dissimilar materials, graphite was removed to a certain depth from the cast iron surface through de-graphitization heat treatment. As the heat treatment time increased, the depth at which graphite was removed increased, showing a linear relationship between the heat treatment time and depth. Aluminum was filled to a certain depth on the de-graphitized cast iron surface through die-casting method, and no intermetallic compounds were formed on the cast iron-aluminum interface. The interfacial bonding strength showed a value of 90 MPa regardless of the heat treatment time, which is very high compared to the 12MPa bonding strength of the material without de-graphitization heat treatment. This result is thought to be due to the mechanical bonding of the undercut structure as the liquid aluminum, penetrated by the high pressure die-casting process, solidified in the de-graphitized region of the cast iron.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.17-19
• /
• 2002

Melt textured YBCO superconductors were fabricated by the top seeding method using Sml.8($Sm_{1.8}$ $Ba_{2.4}$ $Cu_{3.4}$$O_{7-Y}$) seed. We investigated the twin structures using the optical microscope, SEM and TEM. The twin structures formed during the tetragonal to orthorhombic transition which occurred at $450^{\circ}C$ in sample oxygen annealing. The twin structures were clearly observed by SEM due to the chemical etching effects. The lengths of twin structures were increased as the oxygenation heat treatment time increased from 1hr to 10hr. We investigated twin structure by TEM. The twin spaces were considered to be related to the oxygen contents. The results suggested an oxygen diffusion model for the formation of the twin lengths.

• Journal of the Korean Applied Science and Technology
• /
• v.18 no.4
• /
• pp.316-324
• /
• 2001

To prepare an acrylic type pressure-sensitive adhesive, quarternary polymers were synthesized from butyl acrylate (BA), 2-ethyl hexyl acrylate (2-EHA), methyl methacrylate (MMA), and 2-hydroxy ethyl methacrylate (2-HEMA). The quarternary polymers were identified by FT-IR and Molecular weight was measured by Gel Pearmeation Chromatography. Also, viscosity, solid content and peel strength were examined. The peel strength was 160 $g_{f}/25$ mm when the volume ratio of feed monomer to solvent was 1.3:1, and the ratio was relevant to commercial usage. The pot life of adhesive was 30 sec at the 50 m/min of heat treatment rate at, and it indicated that the minimum drying time was 30 sec. In weathering resistance test, peel strength of $160{\sim}180$ $g_{f}/25$ mm after 1000 h, with no residual remains on the adhesive surface.

• Proceedings of the Korean Environmental Health Society Conference
• /
• 2002.04a
• /
• pp.16-19
• /
• 2002

This study was carried out to establish the standardized analysis method in order to decide accurate concentrations of hazardous metals in the air. Acid decomposition method used usually was compared to microwave digestion method. Comparing results of tested background concentration in blank filter, we found that the magnitude of element concentration was Na, Ca, K, Mg, Al and Ba by order. The element concentrations of Glass fiber filter were higher than those of Quartz fiber filter, and the number of undetected components in Glass fiber filter was lower than that in Quartz fiber filter. Thus it is supposed that the concentration of background elements in Glass fiber filter was higher than those in Quartz fiber filter The extraction rate of microwave digestion method was superior to those of acid decomposition method during the test of blank filter as well as SRM of NIST. In case of the SRM of NIST, the average extraction efficiency of acid decomposition Method and microwave pretreatment is 53.8∼82.7％, 81.3∼97.1％, respectively. This result might be caused by the closed system of Microwave, which make outflow and loss of components less. Also microwave digestion method has other merits such as the minimization of time, reagents, and contamination. Furthermore, if the extraction condition, extraction time and used acids are optimized, the better results will be represented.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.12 no.3
• /
• pp.179-189
• /
• 2014

Pyroprocessing has been developed for the purpose of resolving the current spent nuclear fuel management issue and enhancing the recycle of valuable resources. An electrolytic reduction of the pyroprocessing is a process to reduce oxides into metals using LiCl as an electrolyte and requires a post-treatment process due to the inclusion of residual salt in porous metal products. A vacuum distillation has been adopted for various molten salt systems and could be applied to the post-treatment process of the electrolytic reduction. The residual salt in the metal products includes LiCl, alkali chlorides, and alkaline earth chlorides. In this paper, vapor pressures of chlorides have been estimated and the composition changes on the residual liquid during the vacuum distillation process have been calculated. A model combining a material balance and vapor-liquid equilibrium relations has been proposed under a constant vapor discharging flow rate and liquid composition changes have been calculated using the vapor pressures with respect to a dimensionless time. The behaviors have been compared with temperature and molten salt composition changes to simulate the process condition variation. The distillation of the residual salt has been dominated by LiCl which is the main component of the salt and CsCl of which vapor pressure is higher than that of LiCl would be readily removed. RbCl exhibits similar vapor pressure with LiCl and maintains its composition. However, $SrCl_2$ and $BaCl_2$ of which vapor pressures are much lower than that of LiCl are concentrated with time and expected to be possibly precipitated during the distillation when the initial compositions are increased.

• Journal of Adhesion and Interface
• /
• v.1 no.1
• /
• pp.15-22
• /
• 2000

To prepare acrylic type pressure-sensitive adhesive, quarter polymers were synthesized from butylacrylate (BA), 2-ethylhexylacrylate (2-EHA), methyl methacrylate (MMA), 2-hydroxyethylmethacrylate (2-HEMA). The quarter polymer was identified by FT-IR. Molecular weight was measured by Gel Pearmeation Chromatograhy. Also, viscosity, solid content and peel strength were investigated. The peel strength was $160g_f/25mm$ when the volume ratio of feed monomer to solvent was 1.3:1 and the ratio was relevant to commercial usage. The pot life of adhesive was 30 s at the 50 m/min of heat treatment rate, and it indicated that the minimum drying time was 30 s. Not only weathering resistance keep up peel strength $160{\sim}180g_f/25mm$ after 1000 h, but also no residual remains.

• Korean Journal of Veterinary Service
• /
• v.47 no.2
• /
• pp.61-72
• /
• 2024

This study aimed to evaluate the feasibility of percutaneous endoscopic foraminotomy (PEF) for the treatment of intervertebral disc herniation of the thoracolumbar spine in large-breed dogs by comparing it with open hemilaminectomy (OH). Six large-breed canine cadavers were used in the present study. A barium and agarose mixture (BA-gel) simulating intervertebral disc herniation was injected into the spinal canal at two intervertebral spaces (T12-T13, L2-L3) of the thoracolumbar spine in each cadaver. PEF and OH were randomly allocated to the sites in each cadaver. Computed tomography was performed pre- and postoperatively. The incision length, vertebral window size, procedure time, and amount of simulated disc material removed were recorded to compare PEF and OH. Both procedures clearly exposed the simulated disc material and spinal cord. The size of the incision and vertebral window created after PEF was much smaller than those after OH. The surgical duration of PEF was longer than that of OH. However, no significant difference (P>0.05) was observed in the amount of BA-gel removed between PEF and OH. Thus, PEF could be used as an effective surgical option for intervertebral disc herniation of the thoracolumbar region in large-breed dogs in that it could lead to less tissue damage as well as sufficient removal of the simulated disc material.