• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.10
• /
• pp.571-578
• /
• 1999

Current waveform control of pulse MAG welding power source is studied so that welding of thin plates may obtain high speed and improved performance. In this paper, waveform control method is proposed, digital controller using DSP is able to control the current waveform precisely. High speed welding of thin plates using pulse MAG welding method is made possible. Performance test for 1.2mm thin plates is carried out, output waveform and welding performance is analyzed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.7
• /
• pp.1167-1174
• /
• 2008

The measurement of two-dimensional magnetic properties of electrical steel sheet using single sheet tester (SST) requires to control the B-waveform as sinusoidal. The SST electric circuit, in general, has inductance, and this makes the phase lag in electric current. For this reason, the induced voltages of H- or B-coil may have phase difference from the exciting voltage. In this paper, a new algorithm is developed to compensate the phase difference and makes the B-waveform control efficient. The developed algorithm experimentally calculates the phase difference based on the measured waveform of the induced voltage for the magnetic field intensity along transverse direction. By using the proposed algorithm, the two-dimensional magnetic properties of grain-orientated electrical steel sheet (30PG110) is measured up to 2T. By comparing the measured B- and H-waveforms, the effectiveness of the proposed algorithm is proven.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.5
• /
• pp.257-263
• /
• 1999

Recently the performance of CO2 arc welding machine has been advanced significantly through the adoption of inverter circuit topology which made it possible to control the waveform of welding current and thus to suppress the spatter generation. However, the optimum waveform is still uncertain. As a first step for figuring out the promising waveforms, this study was performed to set-up the experimental system for studying the effect of waveform variables, The system designed in this study is a digital controller using single chip microprocessor of 80C196KC. As a result of performance test of this system, it was demonstrated all of the waveform variables could be set individually and the resultant waveforms appeared to be pretty much the same as the intended one.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.7
• /
• pp.430-436
• /
• 2004

This paper presents an advanced control technique for power density maximization of the Brushless DC (BLDC) generator by using the linear tracking method. In a generator of given rating, the weight and size of the system affect the fuel consumption directly. Therefore, power density is one of the most important issues in a stand-alone generator. BLDC generator has high power density in the machine point of view and additional increases of power density by control means can be expected. Conventional rectification methods cannot achieve the maximum power possible because of hon-optimal current waveforms. The optimal current waveform to maximize power density and minimize machine size and weight in a nonsinusoidal power supply system has been derived, incorporated in a control system, and verified by simulation and experimental work. A new simple algebraic method has been proposed to accomplish the proposed control without an FFT which is time consuming and complicated.

• Journal of Digital Convergence
• /
• v.11 no.5
• /
• pp.285-290
• /
• 2013

In a MPC coding using excitation source of voiced and unvoiced, it would be a distortion of speech waveform. This is caused by normalization of synthesis speech waveform of voiced in the process of restoration the multi-pulses of representation section. To solve this problem, this paper present a method of position compensation(PC-MPC) in a multi-pulses each pitch interval in order to reduce distortion of speech waveform. I was confirmed that the method can be synthesized close to the original speech waveform. And I evaluate the MPC and PC-MPC using multi-pulses position compensation method. As a result, $SNR_{seg}$ of PC-MPC was improved 0.4dB for female voice and 0.5dB for male voice respectively. Compared to the MPC, $SNR_{seg}$ of PC-MPC has been improved that I was able to control the distortion of the speech waveform finally. And so, I expect to be able to this method for cellular phone and smart phone using excitation source of low bit rate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.9
• /
• pp.4119-4124
• /
• 2011

In a MPC coding using excitation source of voiced and unvoiced, it would be a distortion of speech waveform in case of increasing or decreasing of speech signal amplitude in a frame. This is caused by normalization of synthesis speech signal in the process of restoration the multi-pulses of representation section. To solve this problem, this paper present a method of amplitude compensation(AC-MPC) in a multi-pulses each pitch interval in order to reduce distortion of speech waveform. I was confirmed that the method can be synthesized close to the original speech waveform. And I evaluate the MPC and AC-MPC using amplitude compensation method. As a result, SNRseg of AC-MPC was improved 0.7dB for female voice and 0.7dB for male voice respectively. Compared to the MPC, SNRseg of AC-MPC has been improved that I was able to control the distortion of the speech waveform finally. And so, I expect to be able to this method for cellular phone and smart phone using excitation source of low bit rate.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.12
• /
• pp.622-628
• /
• 2005

This paper is given a full detail of mathematical analyses of input current and output voltage for a novel active type power factor correction (PFC) converter. These are compared with harmonics components of input current for a conventional PFC converter. The proposed PFC converter is constructed in using a new loss-less snubber circuit to achieve a soft switching of control device. Also the proposed converter for discontinuous conduction mode (DCM) eliminates the complicated circuit control requirement and reduces the size of components. The input current waveform in the proposed converter is got to be a sinusoidal form of discontinuous pulse in proportion to magnitude of ac input voltage under the constant duty cycle switching. Therefore, input power factor is nearly unity and the control method is simple. Particularly, the stored energy of loss-less snubber capacitor is recovered with input side and increases input current from resonant operation. The result is that input power factor of the proposed converter is higher than that of conventional PFC converter. Some simulative results on computer and experimental results are included to confirm the validity of the analytical results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.1
• /
• pp.62-71
• /
• 2009

In this paper, an improved drive method of piezoelectric PZT stack actuator for micro-positioning system is proposed and the performances are evaluated. This type of amplifier is based on switching technology efficiently handling the arbitrary regenerative energy from the piezoelectric actuator. The conventional voltage-feedback control method has the THD of -32dB (${\approx}2.5%$) with 100mHz sinusoidal reference, which means that the positioning performance in linearity degrades due to the hysteretic relationship between actuator voltage and the displacement. This paper proposed an improved charge-controlling method, which utilizes differential information of charge reference instead of integrating the actuator's current. The current waveform has THD under -40dBV (=1%) and the displacement waveform nearly -52dB (${\approx}0.25%$), which means that the positioning performance is very excellent. Finally, another method of the displacement feedback control has better performance than the voltage method, however there exists a limitation in performance of the system.

• Journal of the Korean Magnetics Society
• /
• v.7 no.6
• /
• pp.327-333
• /
• 1997

We designed and constructed the high frequency magnetic characteristics measurement system to measure core loss, B-H curve, permeability of toroidal ferrite core, amorphous core and various materials for high frequency application. The system consists of universal equipments such as digitizing oscilloscope, signal generator, power amplifier, PC in order to make upgrade easily. The power source is composed of waveform synthesizer and power amplifier ranging from DC to 20 MHz, and output signal H and B from sample core are digitized by oscilloscope with sampling rate 1 GS/ s per channel. Computer controls power source and oscilloscope, reads data from oscilloscope, displays analyzed waveform and saves data with file. The entire procedures finishes within few seconds.

• Journal of Digital Convergence
• /
• v.10 no.5
• /
• pp.233-238
• /
• 2012

In a speech coding system using excitation source of voiced and unvoiced, it would be a distortion of speech waveform in case of exist a voiced and an unvoiced consonants in a frame. To solve this problem, this paper present a method of LMS-MPC uses individual pitch and LMS(Least Mean Square). I evaluate the MPC and LMS-MPC using LMS. As a result, SNRseg of LMS-MPC was improved 1.5dB for female voice and 1.3dB for male voice respectively. Compared to the MPC, SNRseg of LMS-MPC has been improved that I was able to control the distortion of the speech waveform finally. And so, I expect to be able to this method for cellular phone and smart phone using excitation source of low bit rate.