• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.6
• /
• pp.540-547
• /
• 2004

In this paper, a current - mode class D(CMCD) power amplifier over 70 % power added efficiency at 900 ㎒ is designed and implemented. Based on push-pull class B structure, main power loss due to charge and discharge of output capacitance in switching mode power amplifier is minimized by applying a parallel harmonic control circuit. Experimental CMCD amplifier with 73 % power added efficiency at 3.2 W and 72 % power added efficiency at 5 W are achieved respectively. In addition a characteristic of switching mode power amplifier whose output power is proportional to magnitude of U power is verified.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.1
• /
• pp.19-25
• /
• 2002

This paper presents novel architectures for power amplifier (PA) relying on 3rd harmonic-tuning technique and dual feeding antenna structure for the isolation of the Tx and the Rx ports. Active integrated antenna (AIA) with power amplifier makes the problem of the isolation between the Tx and the Rx ports occur So, this paper suggests dual feeding and dual resonant structures of the AIA with PA are possible to obtain the high isolation between the Tx and the Rx signals. Dual resonant triangular microstrip antenna, which can replace power amplifier tuning circuit, with slots-loaded and characteristic of the isolation between the Tx and the Rx ports using inset microstrip line feeding and probe feeding methods is proposed and experimentally studied for the case of thin substrate.

• Journal of Korean Society of Forest Science
• /
• v.83 no.2
• /
• pp.175-190
• /
• 1994

In order to get fundamental information for prediction of landslide hazard, both forest and site factors affecting slope stability were investigated in many areas of active landslides. Twelve descriptors were identified and quantified to develop the prediction model by multivariate statistical analysis. The main results obtained could be summarized as follows : The main factors influencing a large scale of landslide were shown in order of precipitation, age group of forest trees, altitude, soil texture, slope gradient, position of slope, vegetation, stream order, vertical slope, bed rock, soil depth and aspect. According to partial correlation coefficient, it was shown in order of age group of forest trees, precipitation, soil texture, bed rock, slope gradient, position of slope, altitude, vertical slope, stream order, vegetation, soil depth and aspect. The main factors influencing a landslide occurrence were shown in order of age group of forest trees, altitude, soil texture, slope gradient, precipitation, vertical slope, stream order, bed rock and soil depth. Two prediction models were developed by magnitude and frequency of landslide. Particularly, a prediction method by magnitude of landslide was changed the score for the convenience of use. If the total store of the various factors mark over 9.1636, it is evaluated as a very dangerous area. The mean score of landslide and non-landslide group was 0.1977 and -0.1977, and variance was 0.1100 and 0.1250, respectively. The boundary value between the two groups related to slope stability was -0.02, and its predicted rate of discrimination was 73%. In the score range of the degree of landslide hazard based on the boundary value of discrimination, class A was 0.3132 over, class B was 0.3132 to -0.1050, class C was -0.1050 to -0.4196, class D was -0.4195 below. The rank of landslide hazard could be divided into classes A, B, C and D by the boundary value. In the number of slope, class A was 68, class B was 115, class C was 65, and class D was 52. The rate of landslide occurrence in class A and class B was shown at the hige prediction of 83%. Therefore, dangerous areas selected by the prediction method of landslide could be mapped for land-use planning and criterion of disaster district. And also, it could be applied to an administration index for disaster prevention.

• 한국HCI학회:학술대회논문집
• /
• 2008.02b
• /
• pp.629-633
• /
• 2008

In Korean society, digital contents such as VCC has introduced a new medium of advertisement and has become a culture. This research aims to investigate consumer characteristics for different types of consumption patterns for services dealing with digital contents. A total of 96 statements were extracted from literature review and popular press articles and 39 participants participated in this study. The results show 6 types of consumption patterns: Gak-jang-ee, Second-level Celebrity, Viewers, Politicians, Humanists, and Paris Hilton. These groups demonstrate consumer's behavioral characteristics and personal values. This study is meaningful in that it provides an insight for marketing strategies for corporations dealing with digital contents such as VCC.

• Fire Science and Engineering
• /
• v.25 no.3
• /
• pp.51-56
• /
• 2011

The full-scale experiments are carried out to investigate the fire suppression characteristics of water-based fire fighting systems in a road tunnel. Applied systems are the low-pressure water spray system at 3.5 bar and the high-pressure water mist system at 60 bar. The water flow rate of the high-pressure system is one sixth only of the water spray system. A passenger car and a heptane fuel pan with area of $1.4m^2$ are used as fire sources. A blower system is installed at the tunnel exit to realize the longitudinal ventilation conditions (0.9~3.8 m/s) in the tunnel. Temperatures from the fire source to the down-stream direction are measured by K-type thermocouple trees. The experimental results show that the cooling effect of the high pressure water mist system in the test conditions were equivalent to that of the low pressure water spray system for B-class fire.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.12A
• /
• pp.1932-1938
• /
• 1999

In this paper, planar duplexer module combined with power amplifier is described. This new scheme is to enhance power efficiency as well as to minimize the size of RF circuit in CDMA phone. Each filter which was a part of duplexer, was realized with planar type and rearranged into the power amplifier module on the multilayer board. Each electrical specifications of existing power amplifier and duplexer were satisfied. Especially, ACPR performances measured at output power of 24dBm which is 2dB lower than that of a conventional one, meet IS-95 for a power amplifier of CDMA phone. Overall current about 80mA has been successfully saved as a result of new scheme. In addition, the module size has been reduced to be as small as 1.08CC.

• Fire Science and Engineering
• /
• v.27 no.5
• /
• pp.38-43
• /
• 2013

An automatic spreading fire extinguisher usually installed in a closed area like a boiler room, a laundry store or a restaurant's kitchen room is one of the fire protection equipments. This extinguisher automatically discharges dry powder, extinguishing fire. As this extinguisher has the extinguishing capability applicable to the nominal protection area, objects outside the area cannot be properly extinguished. However only its number is being requested according to the floor area in the related laws, and the extinguishing capability depends on the distance from a fire source. In this study we tried to investigate the extinguishing capability of the automatic spreading fire extinguisher in accordance with horizontal separation distance from a fire source. It appeared that the maximum horizontal separation distance was about 30 cm for both class A and B fire to be certainly extinguished.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.5
• /
• pp.59-67
• /
• 2014

In tension lap splices of straight deformed bars, KCI Code (KCI2012) and ACI Code (ACI318-11) requires that the lap lengths for class B splice are 1.3 times as development length. KCI2012 contains development length provisions for the use of headed deformed bars in tension and does not allow their tension lap splices. The purpose of this experimental study is to evaluate that KCI2012 equation for the development length, $l_{dt}$, of headed bars can be used to calculate the lap length, $l_s$, of headed deformed bars in grade SD400 and SD500, having specified yield strength of 400 and 500 MPa. Test results showed that specimens with $l_s$ equal to $1.3l_{dt}$ had maximum flexural strengths as 1.16~1.31 times as the nominal flexural strengths, flexural failure mode, and ductility. These observations indicate that $1.3l_{dt}$ is suitable to the tensile lap length of headed deformed bars in grade SD400 and SD500.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.13 no.1
• /
• pp.1-6
• /
• 2017

In this paper, the flow characteristics of water in the water supply pipes of a WBC array were evaluated. We simulated the flow velocities and pressures for a standard pipe, an expansion pipe with a concentric reducer, and an expansion pipe with an eccentric reducer using computational fluid dynamics. In the case of the standard pipe, when the inlet flow velocities were 0.5 m/s and 2.0 m/s, the maximum flow velocities at the center of the WBC array were 0.54 m/s and 2.74 m/s, respectively, which were the greatest values among those of all the pipe models considered. In the case of the expansion pipe, the maximum flow velocities at the center of the WBC array were almost the same under the same conditions regardless of the type of reducer. The pressure losses in the pipe due to the concentric and eccentric reducers were found to be (165.09 ${\times}$ inlet $velocity^{1.6677}$) and (210.98 ${\times}$ inlet $velocity^{1.6478}$), respectively. The coefficient of determination at this time was greater than 0.99 and was the same for both the models. As a simulation result, it was found that in order to reduce the pressure loss when pipe with WBC array is connected with a conventional pipe, diameter of the pipe with WBC array at that section should be enlarged by one step, and then connected to the conventional pipe with a concentric reducer.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.6
• /
• pp.1602-1609
• /
• 1998

In this paper, the design and implementation of the novel RF front end circuit for CDMA based PCS phone is described. This novel scheme is realized by building the power amplifier module combined with duplexer. The dielectric filters which are parts of duplexer are broken up and relocated into the module. Electromagnetic analysis for via holes and coupling between narrow transmissio lines is icluded to design a circuit. The combined moule has been minimaturized to be as small as 1.5CC. It has satisfied IS-95 requirements for linearity performances of CDMA signal at 24-dBm output power as well as played apart as a duplexer. The operating current of about 95mA has been saved owing to both rearranging dielectric filters and limiting operating point to class-B by considering real working power range of CDMA phones.