• 한국지반공학회논문집
• /
• 제35권12호
• /
• pp.25-33
• /
• 2019

본 연구에서는 수직증축 구조물의 기존말뚝의 축강성(K_ve)을 이론적인 접근과 현장 계측 결과를 바탕으로 추정하였다. 이론적인 접근에는 Randolph와 Wroth(1978)가 제안한 축강성 공식을 적용하여, 지중에 설치된 강성 및 연성말뚝의 세장비(L/D)에 따른 축강성의 범위를 도출하였다. 여기에, 1995 - 1997년 사이에 설치된 38본 말뚝의 계측된 시공 당시 축강성을 이론적으로 도출한 축강성 범위에 중첩해서 고려하였다. 이를 통하여, 노후화와 열화에 의하여 감소한 기존말뚝의 축강성의 최대값을 세장비에 따라 제안하였고, 도출된 값을 통계적인 기법을 통하여 상위 95% 값을 제안하여 신설 보강말뚝 설계 시 필요한 최소 축강성(K_vr)을 산정하는 데에 활용할 수 있도록 하였다.

• 한국지반신소재학회논문집
• /
• 제21권2호
• /
• pp.39-48
• /
• 2022

사보강버팀보는 수평버팀보와 달리 토압이 발생할 경우 설치각에 의한 휨거동이 발생하기 때문에 버팀보의 축강성만이 요구되는 탄소성해석으로는 그 적용에 대한 한계가 존재한다. 따라서, 본 연구에서는 탄소성해석시의 사보강버팀보에 대한 해석방안을 제시하기 위하여 축강성데이터를 수정하는 방안으로의 접근을 시도하였으며, 이를 위하여 선형탄성해석을 이용하였다. 그리고, 선형탄성해석을 통하여 실제현장에 설치된 사보강버팀보에 대한 축강성데이터를 산정하였다. 산정한 사보강버팀보의 축강성데이터는 탄소성해석에 적용하여 흙막이벽체의 거동을 확인하였으며, 이를 계측결과 및 유한요소해석결과와 비교하여 그 적용성을 평가하였다. 연구 결과 선형탄성해석을 이용하여 사보강버팀보의 축강성데이터를 적용한 경우(Case 1, Case 3)는 버팀보의 축강성을 적용하는 일반적인 방법(Case 2, Case 4)에 비하여 축강성데이터는 9~17% 수준으로 감소하였으며, 탄소성 해석시의 흙막이벽체의 변위는 25.33%~64.42%로 증가하였다. 이 결과를 계측결과와 비교한바 선형탄성해석을 활용한 경우(Case 1, Case 3)는 탄소성해석시의 흙막이벽체 거동을 더욱 잘 나타내었다.

• 전산구조공학
• /
• 제8권4호
• /
• pp.159-171
• /
• 1995

한 cycle의 이력곡선 loop을 완전히 표현하기 위해서는 pinch force, drift offset, effective stiffness, unloading, reloading, tangential stiffness 등의 변수가 필요하게 된다. 각 이력 loop에 대해 이들 변수들은 에너지 소산정도에 따라 변위와 축력의 함수로 표현될 수 있다. 본 논문에서는 먼저 16개의 전단벽 실험에서 얻어진 이력곡선 데이타를 분석하여 앞에 기술된 모든 변수를 표준화된 변위(.DELTA/.DELTA.y)의 함수로 표현했으며 이를 바탕으로 이력곡선의 포락선으로 표현되는 힘-변위관계를 예측할 수 있는 6개의 step을 제시하였다. 제시된 기법으로 구해진 비탄성 힘-변위관계는 실험곡선과 비교되었으며 내진설계에 있어서 가장 중요한 요소중 하나인 구조물의 비탄성 힘-변위관계를 예측하는 편리한 기법으로 이용될 수 있음을 보였다.

• Steel and Composite Structures
• /
• 제30권4호
• /
• pp.315-325
• /
• 2019

Double skin composite walls offer structural and economic merits over conventional reinforced concrete counterparts in terms of higher capacity, greater stiffness, and better ductility. This paper investigated the axial behavior of double skin composite walls with steel truss connectors. Full-scaled tests were conducted on three specimens with different height-to-thickness ratios. Test results were evaluated in terms of failure mode, load-axial displacement response, buckling loading, axial stiffness, ductility, strength index, load-lateral deflection, and strain distribution. The test data were compared with AISC 360 and Eurocode 4 and it was found that both codes provided conservative predictions on the safe side.

• Computers and Concrete
• /
• 제23권5호
• /
• pp.335-349
• /
• 2019

A low-cycle loading experiment of 16 transfer column specimens was conducted to study the influence of parameters, likes the extension length of shape steel, the ratio of shape steel, the axial compression ratio and the volumetric ratio of stirrups, on the shear distribution between steel and concrete, the concrete damage state and the degradation of lateral stiffness. Shear force of shape steel reacted at the core area of concrete section and led to tension effect which accelerated the damage of concrete. At the same time, the damage of concrete diminished its shear capacity and resulted in the shear enlargement of shape steel. The interplay between concrete damage and shear force of shape steel ultimately made for the failures of transfer columns. With the increase of extension length, the lateral stiffness first increases and then decreases, but the stiffness degradation gets faster; With the increase of steel ratio, the lateral stiffness remains the same, but the degradation gets faster; With the increase of the axial compression ratio, the lateral stiffness increases, and the degradation is more significant. Using more stirrups can effectively restrain the development of cracks and increase the lateral stiffness at the yielding point. Also, a formula for calculating the yielding lateral stiffness is obtained by a regression analysis of the test data.

• 한국정밀공학회지
• /
• 제17권3호
• /
• pp.174-183
• /
• 2000

Non-Parallelism the axial direction occurs during grinding process of long slender shafts. The reason for the axial error is due to elastic deformation of the components, accumulation phenomenon of the grinding and wheel wear during the grinding process. The accumulation phenomenon, the size generation mechanism and the wheel wear process during traverse grinding result in complicated process at each step on the wheel surface. The grinding system stiffness obtained from the stiffness of the center on the tailstock and the workpiece varing according to the relative position of the wheel and the workpiece. Further more, the value of wheel wear increases as the grinding process advances. The above mentioned issues make the shape generation process during traverse grinding quite complicated. This research analyzes the shape generation process in the direction of the work spindle. First, the formulation of the grinding system stiffness was conducted and the simulation analysis method of the traverse grinding was established. Also, a measuring system for assessing the dimensinal accuracy of the workpiece has been developed.

• Structural Engineering and Mechanics
• /
• 제11권4호
• /
• pp.357-372
• /
• 2001

In this paper, cantilevered tall structures are treated as cantilever bars with varying cross-section for the analysis of their free longitudinal (or axial) vibrations. Using appropriate transformations, exact analytical solutions to determine the longitudinal natural frequencies and mode shapes for a one step non-uniform bar are derived by selecting suitable expressions, such as exponential functions, for the distributions of mass and axial stiffness. The frequency equation of a multi-step bar is established using the approach that combines the transfer matrix procedure or the recurrence formula and the closed-form solutions of one step bars, leading to a single frequency equation for any number of steps. The Ritz method is also applied to determine the natural frequencies and mode shapes in the vertical direction for cantilevered tall structures with variably distributed stiffness and mass. The formulae proposed in this paper are simple and convenient for engineering applications. Numerical example shows that the fundamental longitudinal natural frequency and mode shape of a 27-storey building determined by the proposed methods are in good agreement with the corresponding measured data. It is also shown that the selected expressions are suitable for describing the distributions of axial stiffness and mass of typical tall buildings.

• Structural Engineering and Mechanics
• /
• 제77권2호
• /
• pp.179-196
• /
• 2021

Experimental investigations on the seismic behaviors of the PVC-FRP Confined Reinforced Concrete (PFCRC) columns under low cyclic loading are carried out and two variable parameters including CFRP strips spacing and axial compression ratio are considered. The PFCRC column finally fails by bending and is characterized by the crushing of concrete and yielding of the longitudinal reinforcement, and the column with a high axial compression ratio is also accompanied by the cracking of the PVC tube and the fracture of CFRP strips. The hysteretic curves and skeleton curves of the columns are obtained from the experimental data. With the increase of axial compression ratio, the stiffness degradation rate accelerates and the ductility decreases. With the decrease of CFRP strips spacing, the unloading sections of the skeleton curves become steep and the ductility reduces significantly. On the basis of fiber model method, a numerical analysis approach for predicting the skeleton curves of the PFCRC columns is developed. Additionally, a simplified skeleton curve including the elastic stage, strengthening stage and unloading stage is suggested depending on the geometric drawing method. Moreover, the loading and unloading rules of the PFCRC columns are revealed by analyzing the features of the skeleton curves. The quantitative expressions that are used to predict the unloading stiffness of the specimens in each stage are proposed. Eventually, an analytical model for the PFCRC columns under low cyclic loading is established and it agrees well with test data.

• Structural Engineering and Mechanics
• /
• 제88권1호
• /
• pp.25-42
• /
• 2023

This paper presents a finite element (FE) simulation of eccentrically loaded lightweight aggregate concrete-encased steel (LACES) columns with H-shaped steel sections, analytical equations are also established to estimate the columns' axial and bending moment interaction capacities. The validity of the proposed models is checked by comparing the results with experimental data. Good agreements between the test and proposed models' results are found with acceptable agreements. Moreover, design parameters, including the lightweight aggregate concrete (LWAC) strength, eccentricity, column slenderness ratio, and confinement, are studied using the FE analysis, and their efficiency factors are discussed. The results show that the ultimate axial capacity of the LACES composite columns subjected to eccentric loading is negatively affected by the increase in the columns' height, but it is positively affected by the increase of the confinement. Increasing the eccentricity and columns' height reduced the columns'stiffness. In addition, the ultimate capacity of the LACES column is significantly influenced by the LWAC strength and eccentricity, where the ultimate capacity of the LACES column is significantly increased by increasing LWAC strength, and it is remarkably decreased by increasing the eccentricity. When the eccentricity changed from zero to 70 mm, the ultimate axial capacity and stiffness decreased by 67.97% and 63.56%, respectively.

• Structural Engineering and Mechanics
• /
• 제90권5호
• /
• pp.435-446
• /
• 2024

The use of cold-formed steel members is increasing day by day, especially in regions where earthquake effects are intensively experienced. Among cold-formed steel members (CFS), "channel" members are used more than other crosssectional members, especially in buildings or industrial structures. In recent years, several studies have been carried out on the axial load and flexural performance of these members under monotonic loading. In this study, CFS beam-column members were cyclically and monotonically loaded under combined axial load and biaxial bending moments, and their buckling behavior, load bearing capacity, stiffness, ductility, and energy absorption capacity were determined. For this purpose, monotonic and cyclic loading experiments were carried out on 30 CFS channel members at 15 different eccentricities. Then, material properties were determined by axial monotonic tensile and very low cycle fatigue tests for use in numerical studies. From the experimental results, the buckling modes, bearing capacities, ductility, stiffness, and energy absorption capacities of the members were obtained. The characteristics of the members were compared according to the stress state of the lips. According to the data obtained from the displacement transducer placed on the lips and on the back of the web, information about the buckling mode and curvature of the members was obtained. Finally, monotonic, and cyclic loading results were compared to determine the differences in the buckling behavior of the members.