• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.17-22
• /
• 2001

This paper is the first of companion papers, which investigate port-masking effects on lean misfire limit. Port-masking was applied to commercial SOHC 3-valve and DOHC 4-valve engine by inserting masking plates between manifold and port. To induce various conditions of stratification, six types of masking plates were applied. The masking plates were placed in the upstream of injector to prevent wall wetting and two ports were not separated to permit both fuel and air entering through masked port. The results were compared with those by conventional port throttling. The results show that lean misfire limit mainly depends on masking direction, that is, high lean misfire limit is achieved when the port near the spark plug is masked. The mechanism of stratification by masking is different from axial stratification by port throttling. In this case, the rich mixture entering through masked port plays a very important role in the stratification process.

• Journal of Mechanical Science and Technology
• /
• 제18권9호
• /
• pp.1661-1667
• /
• 2004

An experimental study is performed on atomization characteristics and stable operating conditions for the injection of high viscous waste vegetable oil using an effervescent atomizer with 2 aerator tubes. Consideration is given to the effects of ALR and liquid viscosity on the velocity and mean diameter of the injected droplet. It is found that (i) as ALR increases, the axial velocity of the droplet is increased, while half-velocity width and SMD are decreased regardless of the change in liquid viscosities, (ii) the rate of fine drop distribution occupied in the total spray field is increased with an increase in ALR, and (iii) the effect of viscosity on the atomization characteristics is minor. Consequently, it is expected that the effervescent atomizer will exhibit an excellent atomization performance at the high ALR condition, regardless of liquid viscosities.

• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.9-21
• /
• 2000

In this study, the characteristics of high-pressure swirl injector have been studied using a commercial CFD code, STAR-CD and experiment to investigate the effect of the length of orifice and swirl port on the spray characteristics. Influences of swirl port angle and initial conditions have also been examined in terms of penetration depth and Sauter`s mean diameter. Computed results of the spray characteristics are compared with experimental results. The results show that the tangential velocity at the nozzle exit decreases, but the axial velocity increases as swirl port angle is increased. Hence, the static flow rate increases, but the initial spray angle decreases with increasing the swirl port angle. It is also shown that the values of the initial SMD used as input data for spray simulation influences the penetration depth and SMD. The spray pattern from the present numerical simulation agrees well with experimental result.

• 대한수의학회지
• /
• 제6권1호
• /
• pp.76-81
• /
• 1966

This study was conducted to observe the condition of the ramification of the bronchus and pulmonary blood vascular system by injection of vinylite into the bronchial tree and pulmonary blood vessels in normal adult swines. The results obtained were summarized as follows. 1. Lungs of swine were composed of the same pulmonary territories as in lungs of human and dog. 2. Bronchial tree of swine also were axial divergency in the patterns. 3. Ramification of the left and right apical lobes are especially complex patterns but cardiac and diaphragmatic lobes are a little monotonous. 4. Intermediate lobe corresponding to mediobasalis branch of human lungs formed only one lobe in swine lung. 5. Pulmonary artery of right apical lobe was mono branch form in all case by authors observation. 6. $B._2$ streched into the seg. dorsalis of the right apical lobe was especially developed compare to $B._1$, $B._3$ of the seg, apicalis and seg, ventralis.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.168-173
• /
• 2000

Flame aerosol synthesis technology refers to the formation of fine particles from gases in flame and is widely used in practical materials processing. In this paper, an experimental investigation was performed on growth of the silica particles that were generated in $H_2/O_2$ Diffusion Flame by the direct injection or TEOS using Electro-spraying method. in this flame aerosol synthesis, four main parameters or nos interaction (flame temperature, residence time or particle in flame, TEOS flow rate, applied voltage) for particle generation and growth was investigated along the axial direction above the burner. A fairly monodisperse non-aggregated particles were successfully obtained.

• 한국분무공학회지
• /
• 제19권4호
• /
• pp.167-173
• /
• 2014

The spray characteristics of Gas-Centered Swirl Coaxial Injector was investigated that there were different characteristics with or without gas flow. As gas flow was accelerated, the momentum of gas was transferred to the momentum of liquid in the low liquid Reynolds number. Therefore, the axial velocity of liquid was increased and the measured value was smaller than without gas flow. However, in the high momentum flux ratio, the momentum transfer hardly occurred and the results had constant values. As the recess length was increased, the mixing area of gas and liquid also was increased, the results were decreased.

• Journal of Mechanical Science and Technology
• /
• 제18권12호
• /
• pp.2294-2302
• /
• 2004

The objective of this study is to obtain detailed information for the micro fabrication of lead frames by applying spray technology to wet etching process. Wet etching experiments were performed with different etching parameters such as injection pressure, distance from nozzle tip to etched substrate, nozzle pitch and etchant temperature. The characteristics of single and twin spray were measured to investigate the correlation between the spray characteristics and the etching characteristics. Drop size and velocity were measured by Phase-Doppler Anemometer (PDA). Four liquids of different viscosity were used to reveal the effects of viscosity on the spray characteristics. The results indicated that the shorter the distance from nozzle tip and the nozzle pitch, the larger etching factor became. The average etching factor had good positive correlation with average axial velocity and impact force. It was found that the etching characteristics depended strongly on the spray characteristics.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1995년도 가을 학술발표회 논문집
• /
• pp.95-102
• /
• 1995

Procedures for estimation of axial or flexural rigidities of bridge members by neural networks are shown. To treat large scale structures containing many unkwon parameters, substructuring concept is introduced. The measurement points are selected considering the sensitivity of the element stiffnesses of interest. Utilization of relative mode vectors is found to be very effective for the local parameter estimation. Then, the study focuses on the method to obtain the training set enough to represent structures. It is shown that noise injection is effective to reduce the estimation errors caused by measurement noise. Verification of the present method is carried out using a cable-stayed bridge model.

• 한국자동차공학회논문집
• /
• 제12권6호
• /
• pp.23-29
• /
• 2004

This work was conducted to figure out the atomization characteristics of three types of bio-diesel fuels using a common-rail injection system. The process of spray development was visualized by using a spray visualization system composed of a Nd:YAG laser and an ICCD camera, The spray tip penetrations were analyzed based on the frozen images from the spray visualization system. On the other hand, the microscopic atomization characteristics such as the distributions of SMD and axial mean velocity were measured by using a phase Doppler particle analyzer system, It is revealed that the sprays of the bio-diesel fuels have larger SMD than that of diesel fuel mainly due to high viscosity of bio-diesel. Different characteristics of bio-diesel fuels were also measured in spray tip penetrations according to the fuels and mixing ration.

• 한국분무공학회지
• /
• 제4권4호
• /
• pp.24-29
• /
• 1999

In the pressure swirl atomizer, the liquid is injected through tangential passages into a swirl chamber, from which it emerges with both tangential and axial velocity components to form a thin conical sheet at the nozzle exit. This sheet rapidly attenuates, finally disintegrating into ligaments and then drops. The purpose of this study is to measure the spray characteristics according to variation of viscosity of the spray produced by the pressure swirl atomizer. The nozzle tested here were especially designed for this investigation. The discharge coefficient is determined by measuring the volume flow rate with a flow meter and the cone angle of the liquid sheets issuing from the nozzle is obtained from series of photographs of the sheet for various liquid viscosity and injection pressure. And mean drop size is measured by image processing method. It is found that the geometrical characteristics of the nozzle and the variation of viscosity were the influential parameters to determine the spray characteristics such as the cone angle, discharge coefficients and SMD.