• The KSFM Journal of Fluid Machinery
• /
• v.17 no.5
• /
• pp.27-36
• /
• 2014

This paper presents a numerical investigation of the effect of the rotation speed on the performance in a transonic axial compressor with the dihedral stator. Four stator geometries with different stacking line variables were tested in the flow simulations over the whole operating range. It was found that a large shroud loss at the rotor outlet and the subsequent shroud corner separation in the stator passage occurred at low mass flow rate with the 100 % design speed. The hub dihedral stator could suppress the shroud loss region and consequently improve the stall margin. In case of the 70 % design speed condition as the mass flow rate decreased, it was seen that the high loss region was placed at the midspan of the rotor passage. The dihedral stator slightly affected the local diffusion factor, but the performance of the compressor was not changed.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.453-460
• /
• 2000

A test rig is developed for performance test of 1 stage axial-type turbine which is designed by meanline analysis, streamline curvature method, and blade design method using configuration parameters. The purpose of this study is to find the best configuration parameters for designing a high efficiency axial-type turbine blade. To measure the efficiency of turbine stage, a dynamo-meter is installed. Two different stators which are manufactured as an integrated type are developed, and a rotor blade and 5 sets disc are developed for setting different stagger angle. The tip and hub diameters of the test turbine are 300 and 206.4mm, respectively. The rotating speed is 1800RPM, and the extracted power is 2.5kW. Flow coefficient is 1.68 and the reaction factor at meanline is 0.373. The number of stator and rotor of test turbine are 31 and 41, respectively. The Mach number of stator exit flow near hub is 0.164.

• Journal of Drive and Control
• /
• v.20 no.4
• /
• pp.45-53
• /
• 2023

This study optimized the parameters of the helical gear based on the original external meshing helical gear pump, combined with the analysis of the stability and flow of the basic parameters of the equipment; herringbone gears were used to eliminate the axial force generated by the helical gears. An optimized helical gear rotor was built with NX. The error between the simulation and calculation results of pump displacement was 3.95% and the simulation results were valid. Analysis of the outlet pressure and lift changes (maximum change rates of 0.38% and 0.25%), pressure analysis of the XY center plane at different times in the same cycle (no pressure surge or drop), and analysis of the axial force of the primary and driven rotors (axis The axial force is close to 0) were performed. The results showed that the flow pulsation of the external gear pump was slight, the operation was smooth, vibration and friction were reduced, the wear of bearings and other components could be diminished, and the service life of the equipment was extended. The simulation results showed that the external gear pump met the design requirements.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.8
• /
• pp.699-708
• /
• 2021

In this paper, the aerodynamic and aeroacoustic characteristics that vary depending on the rotation axial distance between the upper and lower rotor, which is one of the design parameters of the coaxial rotor, is analyzed in the hovering condition using the computational fluid dynamics. Aerodynamic analysis using the Reynolds Averaged Navier Stokes equation and the aeroacoustic analysis using the Ffowcs Williams ans Hawkings equation is performed and the results were compared. The upper and lower rotor of the coaxial rotor have different phase angle which changes periodically by rotation and have unsteady characteristics. As the distance between the upper and lower rotors increased, the aerodynamic efficiency of the thrust and the torque was increased as the flow interaction decreased. In the aeroacoustic viewpoint, the noise characteristics radiated in the direction of the rotational plane showed little effect by axis spacing. In the vertical downward direction of the axis increased, the SPL maintains its size as the frequency increases, which affects the increase in the OASPL. As the axial distance of the coaxial rotor increased, the noise characteristics of a coaxial rotor were similar with the single rotor and the SPL decreased significantly.

• 유체기계공업학회:학술대회논문집
• /
• 2005.12a
• /
• pp.663-669
• /
• 2005

Performance characteristics of an axial flow fan having distorted inlet flow have been investigated using numerical analysis as well as experiment. Two kinds of hub-cap, round shape and right-angled front shape, are tested to investigate the effect of inlet flow distortion on the fan performance. In case of right-angled front shape, axisymmetric distorted inflow is induced by flow separation at the sharp edge of hub-cap, and the characteristics of the inflow depends on the distance between hub-cap and blade leading edge. Flow analysis of the blade passage is peformed by solving the three-dimensional Reynolds-averaged Navier-Stokes equations. numerical solutions are validated in comparison with experimental data measured by a five-hole probe downstream of the fan rotor. It is found from the numerical results that non-uniform axial inlet velocity profile near the hub results in the change of inlet flowangle. The changed inlet flow angle near the hub invokesa flow separation on the blade surfaces, thus deteriorating the fan efficiency. The effect of the distance between hub-cap and blade leading edge on the efficiency is also discussed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.11 no.4
• /
• pp.10-18
• /
• 2007

A tested micro axial-type turbine consists of two stages and its mean radius of rotor flow passage is 8.4 mm. This turbine could be applied to a driver of micro power system, and its rotational speed in the unloaded state reaches to 100,000 RPM. The performance of this system is sensitive depending on the blade angles of the rotor and stator because it is operated in a low partial admission rate, so a performance test is conducted through measuring the specific output power and the net specific output torque with various blade angles on the nozzle, stator and rotor. The experimental results show that the net specific output torque is varied by 15% by changing the rotor blade angle, and the optimal incidence angle is about $10.3^{\circ}$.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.17-30
• /
• 2002

The design method of turbomachinery has been developed highly. But some geometric dimensions have been determined from the empirical view points. In designing the inlet outer diameter of pump impeller and the hub ratio of blower, satisfactory theoretical grounds have not been presented till now. In the paper, these points are discussed and the method of increasing pump and blower efficiencies are also discussed on the basis of experimental and computational results of flow analysis. Further, the effects of tip clearance of rotor on its efficiency and the interference of rotor and stator blade rows are discussed and some ideas to estimate their effects are presented.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.179-186
• /
• 1999

Three-dimensional flow analysis is implemented to investigate the flow through transonic axial-flow compressor rotor(NASA R67), and to evaluate the performances of k-$\epsilon$ and Baldwin-Lomax turbulence models. A finite volume method is used for spatial discretization. And, the equations are solved implicitly in time with the use of approximate factorization. Upwind difference scheme is used for inviscid terms, but viscous terms are centrally differenced. The flux-difference-splitting of Roe is used to obtain fluxes at the cell faces. Numerical analysis is performed near peak efficiency and near stall. And, the results are compared with the experimental data for NASA R67 rotor. Blade-to-Blade Mach number distributions are compared to confirm the accuracy of the code. From the results, we conclude that k-$\epsilon$ model is better for the calculation of flow rate and efficiency than Baldwin-Lomax model. But, the predictions for Mach number and shock structure are almost same.

• 한국전산유체공학회:학술대회논문집
• /
• 2000.10a
• /
• pp.149-154
• /
• 2000

The flows through a turbomachinery tend to be extremely complex due to its inherent unsteady and viscous phenomena. A good analysis of the flows associated with rotor/stator interactions in turbomachinery will be great help in design stage. In this investigation, unsteady viscous flow structurts through one and half stage of UTRC large scale rotating axial turbine are analysed. The numerical data was compared with experimental data and showed good agreement.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.676-685
• /
• 1993

A mathematical model was developed to quantify the separation process of threshed grain-straw mixtures. It was made to predict the separation loss from a separation unit consisted of stationary crimped sieve with rotating inner rotor. Experiments were performed to prove the mathematical model by changing various levels of pertinent variables for rice. Good Agreement between the simulated results and observed data under the various test conditions, such as inclination angle of the separator, vane pitch, rotor speed, MOG/G ratio, feed rate, and crop variety and moisture content, were confirmed.