• Journal of Advanced Marine Engineering and Technology
• /
• 제18권4호
• /
• pp.69-76
• /
• 1994

Thermal elasto-plastic analysis of axi-symmetric body by the finite element method is presented in this paper for analyzing the process of upset forming of circular section extruded bar. The example of calculation for upset forming of Nimonic extruded bar is also presented. It is shown that remeshing of quadrilateral finite element is necessary because the very highly distorted element by plastic deformation disturbs the calculation. Calculated values for nodal points in new mesh are obtained from nodal points of old mesh by linear interpolation method. The experimental results are compared with calculated values. The appearance of upsetupset forming obtained by experimental method is very similar to that obtained by calculations. So, it is proved that the thermal elasto-plastic analysis of axi-symmetric body by the finite element method is very useful for finding the optimum upsetting condition.

• Journal of Ship and Ocean Technology
• /
• 제8권1호
• /
• pp.1-9
• /
• 2004

Experiments on friction drag reduction by injecting polymer (Polyethylene oxide) solution or micro-bubbles were carried out in the cavitation tunnel of KRISO. Two different drag reduction mechanisms were applied to a slender axi-symmetric body to measure the total drag reduction. And then the amount of friction drag reduction was estimated under the assumption that the reduction mechanisms were effective only to the friction drag component. As the result of the tests, polymer solution drag reduction up to 23％ of the total drag was observed and it corresponds to about 35％ of the estimated friction drag of the axi-symmetric body. This result matched reasonably well to that of the flat plate test "(Kim et al, 2003)". The normalization of the controlling parameters was tried at the end of this paper. Micro-bubble drag reduction was within 1％ of its total drag. This unexpected result was quite different from that of the flat plate case "(Kim et at, 2003)" The possible reasons were discussed in this paper.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제2권4호
• /
• pp.185-194
• /
• 2010

A pumpjet propulsor (PJP) was designed for an underwater body (UWB) with axi-symmetric configuration. Its performance was predicted through CFD study and models were manufactured. The propulsor design was evaluated for its propulsion characteristics through model tests conducted in a Wind Tunnel (WT). In the concluding part of the study, evaluation of the cavitation performance of the pumpjet was undertaken in a cavitation tunnel (CT). In order to assess the cavitation free operation speeds and depths of the body, cavitation tests of the PJP were carried out in behind condition to determine the inception cavitation numbers for rotor, stator and cowl. The model test results obtained were corrected for full scale Reynolds number and subsequently analyzed for cavitation inception speeds at different operating depths. From model tests it was also found that the cavitation inception of the rotor takes place on the tip face side at higher advance ratios and cavitation shifts towards the suction side as the RPS increases whereas the stator and cowl are free from cavitation.

• 한국항공우주학회지
• /
• 제36권5호
• /
• pp.407-419
• /
• 2008

본 연구에서는 축 대칭 원뿔 형상 위의 압축성 경계층의 천이 지점을 선형 안정성 이론과 -method를 이용하여 예측하였다. 축 대칭 좌표계에서의 압축성 유동 지배 방정식으로부터 압축성 원뿔 경계층의 선형 안정성 방정식을 얻었으며 안정성 방정식을 2차 정확도의 유한 차분법을 이용하여 계산하는 수치 프로그램을 개발하였다. 개발 된 코드로 원뿔 경계층의 안정성 특성 및 2차원 교란의 증폭률을 계산하고 실험결과와의 비교를 통해 검증을 수행하였다. 얻어진 교란의 증폭률을 활용하여 -method를 통해 천이지점 예측을 수행하였다. 풍동 시험 및 비행 시험 결과와의 비교를 통해 비행 조건에 있는 마하수 4와 8사이의 원뿔 경계층에 대한 본 연구의 천이지점의 예측 능력을 확인하였다. 또한 벽면 냉각이 경계층 내부 교란의 안정성 및 천이 지점에 미치는 영향을 분석하였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제2권2호
• /
• pp.57-67
• /
• 2010

Experimental investigations were carried out on an Axi-symmetric Body Model fitted with Pump-jet Propulsor (PJP) in the Cavitation Tunnel at Naval Science and Technological Laboratory (NSTL). The tests were intended for evaluating the propulsion characteristics of the body and propulsor. The self propulsion point of the model for two configurations was determined after finding the corrections for tunnel blockage effects and differences in model length at zero trim. The results were found to match closely with the towing tank results. The rotor and stator torques also matched closely over full range of experiment. Further experiments were carried out on the body at $4.5^{\circ}$ angle of trim to investigate the propulsive performance and assess the operational difficulties in the sea. The results indicated an increase in resistance and decrease in rotor thrust; but the balance of torques between the rotor and stator was undisturbed, causing no concern to vehicle roll.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2006년도 추계 학술대회논문집
• /
• pp.20-21
• /
• 2006

Three kinds of jet flows encountered in the practical airframe design phase are discussed in this paper. Firstly, the side jet effect on the cavity flow over the flat plate was investigated. Secondly, the aerodynamic modeling of side jet influence on body-tail configuration was presented. Computational study of the similarity parameters was done to minimize the wind tunnel test. Lastly, supersonic jet impingement on a flat plate surrounded by solid walls was simulated numerically for both axi-symmetric and three-dimensional calculations with moving body method.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1997년도 추계 학술대회논문집
• /
• pp.81-85
• /
• 1997

The Computer code KAIST-ADD LUFUNS has been developed to solve 3D compressible turbluent flow. This method employs Harten-Yee's modified upwind scheme in the explicit part and Steger-Warming Splitting in the implicit part. Flow past RAE wing-body aircraft has been computed for three different flow conditions. The result have shown good comparision with the experimental data. Baldwin-Lomax turbluence model is used for this computer code.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.195-200
• /
• 2010

Numerical investigation was conducted to study the effects of after-body configurations and nozzle lip on the PIFS(Plume Induced Flow Separation) and eat flux to the base face. Two dimensional and axi-symmetric non-equilibrium Navier-Stoke's solver with $k-{\omega}$ SST turbulence model was used to solve the launching vehicle type configuration with propulsive jet. The experimental result of Robert J. McGhee was compared with our computational results for code validation. Three types of the after-body configurations (Straight, Boat-tail, Flare type) were simulated for this study. And the nozzle lip effect was studies using the three types of base configurations same simulation conditions. As a result of numerical investigations, higher pressure ratio condition and boat-tail after-body configuration caused severe PIFS phenomenon but the flare type after-body configuration and low pressure ratio suppressed PIFS. Flare type after-body configuration and low pressure ratio case reduced heat flux to base face. The nozzle lip dispersed the heat flux widely along the base face and the nozzle lip.

• 한국전산유체공학회지
• /
• 제18권4호
• /
• pp.9-16
• /
• 2013

Cavitation on an axi-symmetric hemispherical head-form body was studied using an Reynolds-averaged Navier-Stokes equations solver based on a cell-centered finite volume method. To consider compressibility effects on the vapor phase and cavity interface, a pressure-based compressible flow CFD code was developed. To validate the developed CFD code, cavitating flow around the hemispherical head-form body was simulated using pressure-based incompressible and compressible CFD codes and validated against existing experimental data in the three-way comparison. The cavity shedding behavior, length of re-entrant jet, drag history, and Strouhal number of the hemispherical head-form body were compared between two CFD codes. The results, in this paper, suggested that the computations of cavitating flow with compressibility effects improve the description of cavity dynamics.

• 대한기계학회논문집A
• /
• 제20권10호
• /
• pp.3152-3159
• /
• 1996

Previous works about the cylindrical shape elastic body which is under longitudinal temperature distribution mostly show the results of free expansion, therefore exact thermo-elastic analysis is needed. The object of this work is to analyze the thermo-elastic problem of the hollow cylinder when the cylinder is under longitudinal temperature distribution. In this paper, the analytical solution is found by using Galerkin vector, and it is compared by the results of FEM. For displacements of cylinder, analytical values are almost same as the results of FEM, but free expansion is not fit for analytical solution and the results of FEM. stresses from analytical solution and the results of FEM show good agreement also. but the results are different near the end boundary, since St. Venant principle is applied.