• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.5
• /
• pp.770-778
• /
• 1994

In this paper, the photovoltaic inverter system with instantaneous sinusoidal current tracking control is proposed to improve the utilization factor of photovoltaic power system which would be connected utility interactive system. The proposed inverter is designed to track maximum power point by two-state value control method and utility interactive operation, and to decrease output harmonics component. Optimal operating region is described by state space averaging method, and present tracking condition of standard guide line. The experimental result shows the effectiveness of inverter system using the instantaneous control method.

• Journal of Korea Multimedia Society
• /
• v.17 no.8
• /
• pp.923-936
• /
• 2014

Images can be contaminated with different types of noise, for different reasons. The neighborhood averaging and smoothing by image averaging are the classical image processing techniques for noise removal. The classical spatial filtering refers to the aggregate of pixels composing an image and operating directly on these pixels. To reduce or remove effectively noise in image sequences, it usually needs to use noise reduction filter based on space or time domain such as method of spatial or temporal filter. However, the method of spatial filter can generally cause that signals of objects as the target are also blurred. In this paper, we propose temporal filter using the piece-wise quadratic function model and enhancement algorithm of image quality for the performance improvement of target detection and tracking by heterogeneous noise reduction. Image tracking simulation that utilizes real IIR(Imaging Infra-Red) images is employed to evaluate the performance of the proposed image processing algorithm.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.39-47
• /
• 1992

The engine combustion is one of the most important process affecting performance and emissions. One effective way to improve the engine combustion is to control motion of the charge inside a cylinder by means of optimum induction system design, because the flame speed is mainly determined by the turbulence in a gasoline engine. This paper describes the measurement and characterization of mean velocity and turbulence intensity inside the cylinder of a 4-valve gasoline engine using laser Doppler velocimeter(LDV) under motoring(non-firing) conditions. Since the measured LDV data in each cycle show small cycle variation during compression stroke in the tested engine, the mean velocity and turbulence intensity are calculated by ensemble averaging method neglecting cycle variation effects. In the ensemble averaging method, the effects of the calculation window, in which velocities are assumed as the same crank angle, on mean velocity and turbulence intensity are fully investigated. In addition, the effects of measuring point on the flow characteristics are studied. With large calculation window, the mean velocity is shown to be less sensitive with respect to crank angle and turbulence intensity decrease in its absolute amplitude. When the piston approch to the top dead center of compression, the turbulence intensity is found to be homogeneous in the cylinder.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.12
• /
• pp.137-144
• /
• 2000

In order to achieve systematical method for improving motion accuracy of hydrostatic table, an algorithm using finite element method is proposed in this paper. Quantification of averaging effect of oil film on motion error is performed theoretically by analysis on the relationship between spacial frequency of rail form error and motion error of table. Influences of film stiffness and pocket size on the motion error of table are also analyzed theoretically. Validity of the algorithm is verified experimentally from the test on the motion error of table with three types of rail which have different form profile. Experimental results show that the algorithm is very effective to analyze theoretically the motion error of hydrostatic table.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.5
• /
• pp.139-148
• /
• 2002

Motion errors of linear motion guideway are analyzed theoretically in this paper. For the analysis, an new algorithm predicting motion errors of bearing and guideway is proposed using the Hertz's elastic deformation theory. Accuracy averaging effect can be calculated quantitatively by analyzing relationship between motion errors of guideway and spatial frequency of rail form error. Influences of design parameters on the motion errors including the number of balls, preload, ball diameter, bearing length and the number of bearings are analyzed. As it is difficult to measure the rail form error, experimental results are compared with results analyzed by the equivalent analysis method which evaluate the motion errors of guideway using the measured errors of bearing. From the experimental results, it is confirmed that the proposed analysis method it effective lo analyze the motion errors of linear motion bearing and guideway.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.2
• /
• pp.133-138
• /
• 2014

This paper proposes a low power-loss averaging current mode control using a resistor and bypass switch. Generally, current sensing method using a resistor has a disadvantage of power loss which degrades the efficiency of the entire systems. On the other hand, proposed measurement technique operating with bypass-switch connected in parallel with sensing resistor can reduce power loss significantly the current sensor. An analog-circuited bypass driver is implemented and used along with an average-circuit mode controller. The bypass switch bypasses the sensing current with a small amount of power loss. In this paper, a 50[W] prototype average current mode boost converter has been implemented for the experimental verification.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2006.05a
• /
• pp.1788-1792
• /
• 2006

The ordered weighted averaging (OWA) operator by Yager has received more and more attention since its appearance. One key point in the OWA operator is to determine its associated weights. Among numerous methods that have appeared in the literature, we notice the maximum entropy OWA (MEOWA) weights that are determined by taking into account two appealing measures characterizing the OWA weights. Instead of maximizing the entropy in the formulation for determining the MEOWA weights, the new method in the article tries to obtain the OWA weights which are evenly spread out around equal weights as much as possible while strictly satisfying the orness value provided in the program. This consideration leads to the least squared OWA (LSOWA) weighting method in which the program tries to obtain the weights that minimize the sum of deviations from the equal weights since entropy is maximized when the weights are equal. Above all, the LSOWA weights display symmetric allocations of weights on the basis of equal weights. The positive or negative allocations of weights from the median as a basis depend on the magnitude of orness specified. Further interval LSOWA weights are constructed when a decision-maker specifies his or her value of orness in uncertain numerical bounds.

• Journal of the Korean Solar Energy Society
• /
• v.29 no.6
• /
• pp.1-13
• /
• 2009

Photovoltaic conditioning systems normally use a maximum power point tracking (MPPT) technique to deliver the highest possible power to the load continuously when variations occur in the insolation and temperature. A unique method of tracking the maximum power points (MPPs) and forcing the boost converter system to operate close to these points is presented through deriving small-signal model and transfer function of boost converter considering input capacitor. This paper aims at modeling boost converter including fairly large equivalent series resistance(ESR) of input reservoir capacitor by state-space-averaging method and PWM switch model and compares both methods using Bode plots. In the future, properly designed controller for compensation will be constructed in 3kw real system for maximum photovoltaic power tracking control.

• The Journal of the Korea Contents Association
• /
• v.6 no.12
• /
• pp.21-28
• /
• 2006

In a face detection system based on template matching, histogram equalization or log transform is applied to an input image for the intensity normalization and the image improvement. It is known that they are noneffective in improving an image with intensity distortion by illumination variation. In this paper, we propose an efficient image improvement method using a simple regression analysis combined with a bilateral symmetry average for images with intensity distortion by illumination variation. Experimental results show that our method delivers the detection performance better than previous methods and also remarkably reduces the number of face candidates.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.249-255
• /
• 2011

This paper is about the study of a stand-alone photovoltaic power conditioning system with an energy storage system with battery. The paper proposes the appropriate circuit model of stand-alone PV PCS considering the maintenance of the battery system. It also proposes the buck converter modeling by a state-space averaging method considering characteristics of solar cell. Lastly, it shows the way to choose the suitable battery and to design the model of bi-directional converter for charging and discharging battery. PSIM simulation is used to validate the proposed algothim of the system.