• Analytical Science and Technology
• /
• v.23 no.5
• /
• pp.465-476
• /
• 2010

In this study, a number of volatile organic compounds (VOCs) including benzene, toluene, p-xylene, styrene, and methyl ethyl ketone were analyzed from samples collected in ambient air and under the field conditions. These samples were analyzed independently by two different set-ups for VOC analyses, i.e., between [1] gas chromatography/flame ionization detector with tube sampling - (F-T system) and [2] gas chromatography/mass spectrometer with bag sampling (M-B system). The analytical results derived by both systems showed fairly similar patterns in relative sense but with moderately large differences in absolute sense. The results of M-B system were high relative to F-T system with the F-T/M-B ratio below 1. If the relative biases of the two measurement techniques are derived in terms of percent difference (PD) in concentration values, the results were generally above 35% on average. A student t-test was applied to investigate the statistical significance of those differences between the systems. The results of both analytical systems were different at 95% confidence level for toluene, p-xylene, styrene, and methyl ethyl ketone (P < 0.043). However, F-T and M-B systems showed strong correlations for toluene and p-xylene. The observed bias is explained in large part by such factors as the differences in standard phases used for each system and the chemical loss inside the bag sampler.

• Applied Chemistry for Engineering
• /
• v.32 no.2
• /
• pp.168-173
• /
• 2021

In this study, we measured total flavonoids after extracting the total flavonoids from lemongrass which is known to have a high content of antioxidant ingredients when using microwave energy. Also, optimal extraction conditions of active ingredients using central composite design-response surface methodology (CCD-RSM) were presented. Both ultrapure water and alcohol were used as extraction solvents and the volume ratio of ethanol/ultrapure water, microwave irradiation time, and microwave irradiation power were set as independence variables. And the extraction yield and total flavonoids were measured. The optimal extraction conditions using CCD-RSM were the volume ratio of ethanol/ultrapure water = 56.3 vol.%, the microwave irradiation time = 6.1 min, and the microwave irradiation power = 574.6 W. We could also obtain expected results of yield = 17.2 wt.% and total flavonoids = 44.7 ㎍ QE/mL dw under the optimum conditions. The comprehensive satisfaction degree of this formula was 0.8562. The P-value was calculated for the yield of 0.037 and the total flavonoids content of 0.002. The average error from actual experiments established for the verification of conclusions was lower than 2.5%. Therefore, a high favorable level could be obtained when the CCD-RSM was applied to the optimization of extraction process.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.12
• /
• pp.1881-1889
• /
• 2018

Objective: In dryland areas of China, alfalfa hay (AH) is a possible substitute for concentrate feed for beef cattle. To evaluate the potential benefits of this substitution, we studied the effect of the ratio of AH intake to total dry matter (DM) intake on average daily body-weight gain (ADG), dietary energy utilization status, and economic benefit in Gansu province. Methods: In each of two feeding trials in 2016 (trial 1 [T1], July 3 to 17; trial 2 [T2], August 15 to September 23), crossbred male Simmental calves were allocated to low AH (LA), medium AH (MA), and high AH (HA) feeding groups (n = 4 per group). The target ADG was set as 1 kg for both trials. In a one-way-layout design based on conventional feeding practices in the province, calves received diets containing the different AH amounts, with a constant ratio of corn stover:total DM and decreasing rations of concentrate feed proportional to the increase in AH. Calves in T1 received AH at 15% (T1-LA), 23% (T1-MA), or 31% (T1-HA) of their dietary DM allowances; those in T2 received 9% (T2-LA), 24% (T2-MA), or 34% (T2-HA) AH. Results: Among the T1 groups, both ADG and economic benefit were highest in T1-LA; whereas in T2, they were higher in the T2-LA and T2-MA groups than in T2-HA. Energy digestibility did not significantly differ among the groups in either trial. The dietary AH inclusion ratios of 14% in the warm season and 8% to 21% in the cool season appeared to yield optimal ADG, metabolizable energy intake, and economic benefit. Conclusion: Low-level inclusion of AH, ranging from 8% to 21%, is a practical approach for beef cattle feeding. This modified feeding regimen likely will promote increased growth performance during the fattening stage of beef steers in dryland areas of Gansu province, China.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.2
• /
• pp.215-225
• /
• 2015

Recently, the importance of energy saving and alternative energy is significantly increasing due to energy depletion and the phase change material (PCM) research for saving energy is also actively investigating. In this research, the membrane emulsification using SPG membrane was used to make various microencapsulated phase change material (MPCM) particles which were comprised of $Rubitherms^{(R)}$ (RT-21 and RT-24) core and silica coating. We investigated the pressure of the dispersion phase, the concentration of surfactant, and the ratio of $Rubitherm^{(R)}$ and silica to prepare various MPCM particles. The DSC and TGA were used to examine the heat stability and latent heat properties. Also, PSA, SEM, and optical microscopy were used to confirm the size of $Rubitherm^{(R)}$ particles and the thickness of silica shell. The average of particle size was $7-8{\mu}m$. And, FT-IR was also used to enforce the qualitative analysis. Finally, the MPCM particles obtained from membrane emulsification showed monodispersed size distribution and the heat stability and latent heat were kept up to 80% compared to pure $Rubitherm^{(R)}$. So, it can be effectively used for wallpaper, buildings and interior products for energy saving as PCMs.

• Asian-Australasian Journal of Animal Sciences
• /
• v.30 no.1
• /
• pp.57-63
• /
• 2017

Objective: Two experiments were conducted to determine the effects of adding exogenous phytase and xylanase, individually or in combination, as well as pelleting on nutrient digestibility, available energy content of wheat and the performance of growing pigs fed wheat-based diets. Methods: In Experiment 1, forty-eight barrows with an initial body weight of $35.9{\pm}0.6kg$ were randomly assigned to a $2{\times}4$ factorial experiment with the main effects being feed form (pellet vs meal) and enzyme supplementation (none, 10,000 U/kg phytase, 4,000 U/kg xylanase or 10,000 U/kg phytase plus 4,000 U/kg xylanase). The basal diet contained 97.8% wheat. Pigs were placed in metabolic cages for a 7-d adaptation period followed by a 5-d total collection of feces and urine. Nutrient digestibility and available energy content were determined. Experiment 2 was conducted to evaluate the effects of pelleting and enzymes on performance of wheat for growing pigs. In this experiment, 180 growing pigs ($35.2{\pm}9.0kg\;BW$) were allocated to 1 of 6 treatments according to a $2{\times}3$ factorial treatment arrangement with the main effects being feed form (meal vs pellet) and enzyme supplementation (0, 2,500 or 5,000 U/kg xylanase). Results: In Experiment 1, there were no interactions between feed form and enzyme supplementation. Pelleting reduced the digestibility of acid detergent fiber (ADF) by 6.4 percentage units (p<0.01), increased the digestibility of energy by 0.6 percentage units (p<0.05), and tended to improve the digestibility of crude protein by 0.5 percentage units (p = 0.07) compared with diets in mash form. The addition of phytase improved the digestibility of phosphorus (p<0.01) and calcium (p<0.01) by 6.9 and 7.6 percentage units respectively compared with control group. Adding xylanase tended to increase the digestibility of crude protein by 1.0 percentage units (p = 0.09) and increased the digestibility of neutral detergent fiber (NDF) (p<0.01) compared with control group. Supplementation of the xylanase-phytase combination improved the digestibility of phosphorus (p<0.01) but impaired NDF digestibility (p<0.05) compared with adding xylanase alone. In Experiment 2, adding xylanase increased average daily gain (p<0.01) and linearly improved the feed:gain ratio (p<0.01) compared with control group. Conclusion: Pelleting improved energy digestibility but decreased ADF digestibility. Adding xylanase increased crude protein digestibility and pig performance. Phytase increased the apparent total tract digestibility of phosphorus and calcium. The combination of phytase-xylanase supplementation impaired the effects of xylanase on NDF digestibility.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.2
• /
• pp.250-258
• /
• 2004

An experiment was conducted to examine the effect of a high environmental temperature on the performance, conformation, and carcass characteristics of pigs and the influence of diet. Thirty-six three-way crossed castrated male pigs with average initial body weight of 50.4 kg were used in the experiment. The pig were allocated to the following treatments: two environmental temperatures (20 and $30^{\circ}C$)${\times}$three dietary energy levels (2,980, 3,300 and 3,600 kcal/kg)${\times}$three protein levels (12.8, 15.2 and 17.2%). Daily weight gain was lighter (p<0.01) and feed: gain ratio lower (p<0.05) in pigs at $30^{\circ}C$ than for pigs at $20^{\circ}C$ The pigs at $30^{\circ}C$ were significantly taller with deeper bodies (p<0.05) and significantly longer (p<0.05) both vertically horizontally in the planum nasal when kept at $30^{\circ}C$. The width of body and the circumference of the neck were greater (p<0.05) at $20^{\circ}C$. The lean meat of the loin, middle section, ham, and hind section were significantly greater (p<0.05) in pigs kept at $30^{\circ}C$ and the belly was significantly heavier. The total unsaturated free fatty acids were significantly higher (p<0.05) in the body fat of pigs kept at $20^{\circ}C$ than in that of pigs at $30^{\circ}C$. The results indicated that when pigs are given very restricted same amounts of feed, they may need less energy to maintain their body temperature under moderately high environmental temperature ($30^{\circ}C$); consequently, their performance is better than that of pigs under optimum environmental temperature. The results showed very clearly that weight gain of pigs increased with increasing of dietary protein and energy content. The increasing of dietary protein content seemed more significant when content increasing to 17.2% compared with the 12.8 and 15.2% protein content treatments. The increasing of dietary energy content was more significant when content increasing to 3,600 compared with the other low energy content treatments.

• KIPS Transactions on Computer and Communication Systems
• /
• v.4 no.11
• /
• pp.369-382
• /
• 2015

Energy aware server clusters aim to reduce power consumption at maximum while keeping QoS(quality of service) compared to energy non-aware server clusters. They adjust the power mode of each server in a fixed or variable time interval to activate only the minimum number of servers needed to handle current user requests. Previous studies on energy aware server cluster put efforts to reduce power consumption or heat dissipation, but they do not consider energy efficiency well. In this paper, we propose an energy efficient cluster management method to improve not only performance per watt but also QoS of the existing server power mode control method based on autonomous learning. Our proposed method is to adjust server power mode based on a hybrid approach of autonomous learning method with multi level thresholds and power consumption prediction method. Autonomous learning method with multi level thresholds is applied under normal load situation whereas power consumption prediction method is applied under abnormal load situation. The decision on whether current load is normal or abnormal depends on the ratio of the number of current user requests over the average number of user requests during recent past few minutes. Also, a dynamic shutdown method is additionally applied to shorten the time delay to make servers off. We performed experiments with a cluster of 16 servers using three different kinds of load patterns. The multi-threshold based learning method with prediction and dynamic shutdown shows the best result in terms of normalized QoS and performance per watt (valid responses). For banking load pattern, real load pattern, and virtual load pattern, the numbers of good response per watt in the proposed method increase by 1.66%, 2.9% and 3.84%, respectively, whereas QoS in the proposed method increase by 0.45%, 1.33% and 8.82%, respectively, compared to those in the existing autonomous learning method with single level threshold.

• Nuclear Engineering and Technology
• /
• v.25 no.2
• /
• pp.237-247
• /
• 1993

Activity ratio of two radioactive primary fission products which had sufficiently different half-lives was expressed as functions of cooling time and irradiation histories in which average burnup, irradiation time, cycle interval time and the dominant fissile material of the spent fuel were included. The gamma-ray spectra of 36 samples from 6 spent PWR fuel assemblies irradiated in Kori unit-1 reactor were obtained by a spectrometric system equipped with a high purity germanium gamma-ray detector. Activity ratio $^{l44}$Ce $^{l37}$Cs, analyzed from each spectrum, was used for the calculation of cooling time. The results show that the radioactive fission products $^{l44}$Ce and $^{l37}$Cs are considered as useful monitors for cooling time determination because the estimated cooling time by detection of activity ratio $^{l44}$Ce $^{l37}$Cs agreed well with the operator declared cooling time within relative difference of $\pm$5 % despite the low counting rate of the gamma-ray of $^{l44}$Ce (about 10$^{-3}$ count per second). For the samples with several different irradiation histories, the determined cooling time by modeled irradiation history showed good agreement with that by known irradiation history within time difference of $\pm$0.5 year. From this result, it would be expected to be possible to estimate reliably the cooling time of spent nuclear fuel without the exact information about irradiation history. The feasibility study on identification of and/or sorting out spent nuclear fuel by applying the technique for cooling time determination was also performed and the result shows that the detection of activity ratio $^{l44}$Ce $^{l37}$Cs by gamma-ray spectrometry would be usefully applicable to certify spent nuclear fuel for the purpose of safeguards and management in a facility in which the samples dismantled or cut from spent fuel assemblies are treated, such as the post irradiation examination facility.mination facility.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.12
• /
• pp.1742-1747
• /
• 2012

A total of 96 growing pigs ((Landrace${\times}$Yorkshire)${\times}$Duroc; BW = $26.58{\pm}1.41$ kg) were used in a 6-wk feeding trail to evaluate the effects of fermented chlorella (FC) supplementation on growth performance, nutrient digestibility, blood characteristics, fecal microbial and fecal noxious gas content in growing pigs. Pigs were randomly allotted into 1 of 4 dietary treatments with 6 replicate pens (2 barrows and 2 gilts) per treatment. Dietary treatments were: i) negative control (NC), basal diet (without antibiotics); ii) positive control (PC), NC+0.05% tylosin; iii) (fermented chlorella 01) FC01, NC+0.1% FC, and iv) fermented chlorella 02 (FC02), NC+0.2% FC. In this study, feeding pigs PC or FC01 diets led to a higher average daily gain (ADG) and dry matter (DM) digestibility than those fed NC diet (p<0.05), whereas the inclusion of FC02 diet did not affect the ADG and DM compared with the NC group. No difference (p>0.05) was observed on the body weight, average daily feed intake (ADFI), gain:feed (G:F) ratio, the apparent total tract digestibility of N and energy throughout the experiment. The inclusion of PC or FC did not affect the blood characteristics (p>0.05). Moreover, dietary FC treatment led to a higher (p<0.05) lactobacillus concentration and lower E. coli concentration than the NC treatment, whereas the antibiotic supplementation only decreased the E. coli concentration. Pigs fed FC or PC diet had reduced (p<0.05) fecal $NH_3$ and $H_2S$ content compared with those fed NC diet. In conclusion, our results indicated that the inclusion of FC01 treatment could improve the growth performance, nutrient digestibility, fecal microbial shedding (lower E. coli and higher lactobacillus), and decrease the fecal noxious gas emission in growing pigs when compared with the group fed the basal diet. In conclusion, dietary FC could be considered as a good source of supplementation in growing pigs because of its growth promoting effect.

• The KIPS Transactions:PartC
• /
• v.17C no.3
• /
• pp.259-270
• /
• 2010

In this paper, a Location Information-based Gradient Routing (LIGR) algorithm is proposed for setting up routing path based on physical location information of sensor nodes in wireless ad-hoc networks. LIGR algorithm reduces the unnecessary data transmission time, route search time, and propagation delay time of packet by determining the transmission direction and search range through the gradient from the source node to sink node using the physical location information. In addition, the low battery nodes are supposed to have the second or third priority in case of forwarding node selection, which reduces the possibility of selecting the low battery nodes. As a result, the low battery node functions as host node rather than router in the wireless sensor networks. The LIGR protocol performed better than the Logical Grid Routing (LGR) protocol in the average receiving rate, delay time, the average residual energy, and the network processing ratio.