• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.35-37
• /
• 2008

The light Mg alloys bearing the remarkably high strength, corrosion resistance and elevated temperature stability stand on the center of interest. The accomplishment so far is, however, only by alloy modification without any consideration on the rapid solidification effect. This work is to report not only the effect of rapid solidification of $MgZn_{4.3}Y_{0.7}$ alloy powders, but the extrusion behavior on the materials properties. The average grain size of the atomized powders was about $3-4{\mu}m$. The extrusion was carried out with the area reduction ratio of 10:1 to 15:1. As the ratio increased, homogeneous microstructure was obtained, and the mechanical properties such as tensile strength and elongation were simultaneously increased.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1582-1584
• /
• 2004

The microstructure, electrical, and clamping voltage characteristics of ZPCCY-based varistor ceramics were investigated in the sintering time range of 1${\sim}$3 h. Increasing sintering time promoted the densification, in which the average grain size and density are increased in the range of $11.4{\sim}16.0{\mu}m$ and $5.34{\sim}5.54g/cm^3$, respectively. The nonlinear exponent decresed in the range of 60${\sim}$26 and the leakage current increased in the range of $1.3{\sim}10.7{\mu}A$ with increase of sintering time. The clamping voltage ratio was less than 2 for ratio surge current of 10 A over sintering times.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.06a
• /
• pp.19-22
• /
• 1997

The surface modificaion of alumina by $Al_2$O$_3$/SiC nanocomposite coating was studied in terms of processing and microstructure. A powder slurry of 5 vol% SiC composition was dipcoated onto presintered alumina bodies and pressurelessly sintered at 1$700^{\circ}C$ for 2 h in $N_2$. The used of organic binder and plasticizer in the slurry preparation, and the control of the density of presintered alumina body were found to be necessary to avoid cracking and warping during processing. The nanocomposite coating well bonded to the alumina body with thickness about 110 ${\mu}{\textrm}{m}$. The average grain size of coating (2 ${\mu}{\textrm}{m}$) was much finer than that of alumina body (13 ${\mu}{\textrm}{m}$). Fracture surface observations revealed mostly transgranular fracture for the coating, whereas intergranular fracture for the alumina body. Some pores (about 6%) were observed in the coating layer, although the alumina body showed fully dense microstructure.

• Journal of the Korean Society for Heat Treatment
• /
• v.30 no.6
• /
• pp.258-263
• /
• 2017

The effect of cooling rate on the damping capacity of pure Mg was studied. Two Mg samples with different cooling rates were prepared by heat treatment at 873 K for 24 h, followed by water quenching and by furnace cooling to room temperature, respectively. The average grain sizes of the Mg samples were almost identical regardless of the cooling rate, but more twins were observed in the sample with faster cooling rate. The calculated vacancy fraction was higher in the fast cooling sample than the slow cooling one. It is noted that the fast cooling sample exhibited lower damping capacity both in the strain-amplitude independent and strain-amplitude dependent regions. Higher values of vacancy concentration and number density of twins in the fast cooling sample are considered to be responsible for the deteriorated damping capacity in the strain-amplitude independent and strain-amplitude dependent regions, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.103-106
• /
• 2002

The applicability of models based on fractal morphology to characterize $(Ba\;Sr)TiO_{3}$ thin film surfaces was investigated. The fractal morphology of coated barium strontium titan oxide thin film surfaces was described using fractal dimension from scanning electro microscopy image. The $(Ba\;Sr)TiO_{3}$ coating were deposited on silicon wafers using $(Ba\;Sr)TiO_{3}$ solution and spin coater. BST solution was composited by mol ratio, and then spin-coated from 3 times to 5 times coating on $Pt/SiO_{2}/Si$ substrate. Qualitative thin film analysis was performed with scanning electro microscopy (SEM), and surfaces parameters such as average grain diameter, roughness exponent and fractal dimension were determined.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.257-258
• /
• 2009

Nanocomposites of a epoxy resin are synthesized and evaluated the present study investigated. The effect of nanoclay additives on the properties of diglycidyl ether or bisphenol A(DGEBA) epoxy resin. DGEBA was mixed with 3~7 wt% organically modified layered silicate, Cloisite 30B for three hours. The average grain size of the specimens decreased with adding Cloisite 30B. The dielectric constant showed between 3.2 ~ 3.5 and the dielectric loss showed between 3.2 ~ 5.7 % in all specimens.

• Journal of the Korean Ceramic Society
• /
• v.29 no.11
• /
• pp.877-887
• /
• 1992

Tetragonal zirconia powder with 3 mol% Y2O3 mas mixed with up to 30 vol% of ${\beta}$-SiC powders, and the mixtures were hot-pressed at 1500$^{\circ}C$ for 60 min under a pressure of 30 MPa in Ar atmosphere. Flexural strength and fracture toughness were measured at room-and high-temperature (1000$^{\circ}C$). Evolution of microstructure was also conducted to investigate the effects of SiC addition on the properties of 3Y-TZP ceramics. Average grain size of the composites was about 0.5 $\mu\textrm{m}$, and decreased with SiC addition. Both room- and high-temperature mechanical properties of the composites were improved with SiC content. Particularly, high-temperature strength and fracture toughness of 3Y-TZP/30v/o SiC composite were twice as high as those of 3Y-TZP. The hardness of the composites also increased with SiC content and reached maximum value at 3Y-TZP/30v/o SiC composite.

• Journal of the Korean Ceramic Society
• /
• v.29 no.12
• /
• pp.997-1003
• /
• 1992

Ultra-fine hydroxyapatite powders were synthesized by the hydrothermal reaction of Ca(OH)2 suspension or Ca(NO3)2$.$4H2O solution with (NH4)2HPO4 solution, and the powders were characterized for each synthetic condition. Crystalline hydroxyapatite powders have average grain size of less than 50 nm. By increasing the reaction pressure, the crystallinity was improved, and the crystals were preferentially growing along c-axis. When Ca(NO3)2$.$4H2O of high solubility was used, hydroxyapatite of single phase was produced. However when Ca(OH)2 of low solubility was used more than 0.334 mol/ι, unreacted Ca(OH)2 remained. Diffraction spot patterns of transmission electron microscope show that powders synthesized by the hydrothermal reaction were composed of single crystals of hexagonal phase.

• Journal of the Korean Ceramic Society
• /
• v.28 no.10
• /
• pp.819-823
• /
• 1991

Pure zirconia ceramic fiber experiences severe volume changes through thermal cyclings of heating and cooling. Zirconia fiber was doped with CaO to stabilize the phase and its effect of CaO was studied on volumetric ratio of each phases, phase transition temperature and microstructure. Tetragonal phase was increased as CaO increases up to 10 mol% and cubic phase was stabilized when CaO was added more than 10 mol%. The average grain size of zirconia fiber was increased as CaO increased and transition temperature was shifted to lower temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.76-79
• /
• 2000

The $Ba(Zn_{1/3}Ta_{2/3})O_3$ ceramics were prepared by conventional mixed oxide method. The structural properties of the BZT ceramics with the sintering temperature were investigated by XRD, SEM. The BZT ceramics have a complex-perovskite structure. The BZT ceramics sintered at $1550^{\circ}C$ had a superstructure plane of BZT(100). Increasing the sintering temperature, the bulk density and ordering were increased. The bulk density of the BZT ceramics sintered at $1550^{\circ}C$ was $7.50[g/cm^3]$. Increasing the sintering temperature, the average grain size were increased and pore were decreased.