• Nuclear Engineering and Technology
• /
• 제50권1호
• /
• pp.132-139
• /
• 2018

Nanocrystalline reduced activation ferritic/martensitic (RAFM) steel samples were prepared using surface mechanical attrition treatment (SMAT). Un-SMATed and SMATed reduced activation ferritic/martensitic samples were irradiated by helium ions at $200^{\circ}C$ and $350^{\circ}C$ with 2 dpa and 8 dpa, respectively, to investigate the effects of grain boundaries (GBs) and temperature on the formation of He bubbles during irradiation. Experimental results show that He bubbles are preferentially trapped at GBs in all the irradiated samples. Bubble denuded zones are clearly observed near the GBs at $350^{\circ}C$, whereas the bubble denuded zones are not obvious in the samples irradiated at $200^{\circ}C$. The average bubble size increases and the bubble density decreases with an increasing irradiation temperature from $200^{\circ}C$ to $350^{\circ}C$. Both the average size and density of the bubbles increase with an increasing irradiation dose from 2 dpa to 8 dpa. Bubbles with smaller size and lower density were observed in the SMATed samples but not in the un-SMATed samples irradiated in the same conditions, which indicate that GBs play an important role during irradiation, and sink strength increases as grain size decreases.

• 한국세라믹학회지
• /
• 제49권6호
• /
• pp.485-492
• /
• 2012

Dense and single phase $BiFeO_3$ (BFO) ceramics were prepared using attrition milled calcined (coarse) powders of an average particle size of ${\approx}3{\mu}m$ by conventional sintering process. A relative density of ${\approx}96%$ with average grain size $7.3{\mu}m$ was obtained when the powder compacts were sintered at $850^{\circ}C$ even for a shorter duration of 10 min. In contrast, densification barely occurred at $800^{\circ}C$ for up to 12 h rather the microstruce showed the growth of abnormal grains. The grain growth behavior at different temperatures is discussed in terms of nonlinear growth rates with respect to the driving force. The sample sintered at $850^{\circ}C$ for 12 h showed enhanced electrical properties with leakage current density of $4{\times}10^{-7}A/cm^2$ at 1 kV/cm, remnant polarization $2P_r$ of $8{\mu}C/cm^2$ at 20 kV/cm, and minimal dissipation factor (tan ${\delta}$) of ~0.025 at $10^6$ Hz. These values are comparable to the previously reported values obtained using unconventional sintering techniques such as spark plasma sintering and rapid liquid phase sintering.

• The Plant Pathology Journal
• /
• 제31권4호
• /
• pp.350-362
• /
• 2015

A disease forecast model for bacterial grain rot (BGR) of rice, which is caused by Burkholderia glumae, was developed in this study. The model, which was named 'BGRcast', determined daily conduciveness of weather conditions to epidemic development of BGR and forecasted risk of BGR development. All data that were used to develop and validate the BGRcast model were collected from field observations on disease incidence at Naju, Korea during 1998-2004 and 2010. In this study, we have proposed the environmental conduciveness as a measure of conduciveness of weather conditions for population growth of B. glumae and panicle infection in the field. The BGRcast calculated daily environmental conduciveness, $C_i$, based on daily minimum temperature and daily average relative humidity. With regard to the developmental stages of rice plants, the epidemic development of BGR was divided into three phases, i.e., lag, inoculum build-up and infection phases. Daily average of $C_i$ was calculated for the inoculum build-up phase ($C_{inf}$) and the infection phase ($C_{inc}$). The $C_{inc}$ and $C_{inf}$ were considered environmental conduciveness for the periods of inoculum build-up in association with rice plants and panicle infection during the heading stage, respectively. The BGRcast model was able to forecast actual occurrence of BGR at the probability of 71.4% and its false alarm ratio was 47.6%. With the thresholds of $C_{inc}=0.3$ and $C_{inf}=0.5$, the model was able to provide advisories that could be used to make decisions on whether to spray bactericide at the preand post-heading stage.

• 대한금속재료학회지
• /
• 제50권1호
• /
• pp.34-38
• /
• 2012

Titanium has good deformability, high hardness, high biocompatibility, excellent corrosion resistance and low density. Due to these attractive properties, it has been used in many industrial applications. Dense nanostructured Ti was sintered from mechanically activated Ti and $TiH_2$ powders by high frequency induction heating under pressure of 80 MPa. The advantage of this process is that it allows very quick densification to near theoretical density and inhibition of grain growth. $TiH_2$ powder was decomposed to Ti during sintering. The hardness of Ti increased and the average grain size of Ti decreased with increasing milling time. The average grain sizes of Ti samples sintered from Ti and $TiH_2$ powder milled for 5 hrs were about 26 nm, 44 nm, respectively. The hardness of Ti sintered from Ti and $TiH_2$ powder milled for 5 h was $504kg/mm^2$ and $567kg/mm^2$, respectively.

• 한국작물학회:학술대회논문집
• /
• 한국작물학회 2017년도 9th Asian Crop Science Association conference
• /
• pp.345-345
• /
• 2017

In order to reduce rice cultivation area in paddy fields and to increase domestic self-sufficiency of imported upland grain, it is necessary to increase double cropping area of upland crops in paddy field in accordance with decrease of rice consumption in Korea. The double cropping of spring potato-summer grain maize can be combined because of enough growing season in the southern plain of Korea. Spring potato, which is profitable, can be planted in the late February and harvested in the late May as the main crop. Subsequent grain maize can be planted in early June and harvested in November (maturity in the early October). Spring potato (variety Soomi) yielded $2,544kg\;10a^{-1}$ (tuber) when planted in late February, 2016. When maize was planted in June as the second cropping crop, though growth of plant decreased much, grain yield decreased slightly compared to normal planting in April or May. There was enough time to dry maize ear in the field after maturity before harvesting, which saved labor and time for grain drying, since there is no autumn planting at the double cropping of spring potato-summer grain maize. When grain maize (variety Gwangpyeongok) was planted in the early June (June $10^{th}$), average grain yield of above $860kg\;10a^{-1}$ over 2 years of 2015 and 2016 was obtained, and the annual total yield (potato tuber + maize grain) of 3,400 kg $10a^{-1}$ was obtained. The result indicates that the double cropping of spring potato-summer maize using paddy fields in southern plain of Korea, could contribute to the self-sufficiency of upland crops through the maximum production.

• 한국지형학회지
• /
• 제17권1호
• /
• pp.15-27
• /
• 2010

이 연구는 바람아래해수욕장 주변의 퇴적물 입도조성을 시·공간적으로 분석하여 퇴적환경 변화특성을 고찰하고자 하였다. 연구결과, 2009년 겨울철 표층퇴적물은 크게 자갈, 모래, 역질사, 역니질사, 니질사, 실트질사, 모래질실트 등의 7개 퇴적상으로 구분되었다. 평균입도를 시계열 분석(2002~2009)한 결과, 간석지 퇴적물은 평균 입도가 세립해지고, 분급은 불량해졌다. 그러나 해빈지역은 동일시기에 퇴적물의 입도가 조립화 되었고 분급이 양호해졌다. 이러한 결과는 해빈과 간석지의 퇴적환경 변화가 서로 다른 경향성을 가지고 있기 때문이다. 즉, 할미섬을 중심으로 남서쪽 해빈지역은 외해로 열려 있어 상대적으로 고에너지 환경으로 세립질 퇴적물이 제거되는 환경에서 퇴적된 결과이다. 간석지 중 가장 안쪽의 만입지의 세립화는 왕복성 조류에 의해서 유입된 퇴적물이 정조시에 퇴적되었거나 지형적인 영향에 의한 에너지 감소로 퇴적된 것으로 판단된다. 남서쪽 외해 쪽의 간석지들의 세립화 원인은 규모가 큰 섬옷섬이 외해로부터 유입되는 파랑을 막아주어 상대적으로 저에너지 환경 하에 놓이면서 조석의 영향을 받으면서 세립질 퇴적물질들이 지속적으로 퇴적된 결과로 판단된다.

• 한국재료학회지
• /
• 제22권6호
• /
• pp.303-308
• /
• 2012

This study evaluated the enhancement of microstructural and mechanical properties of a cross rolled Ni-10Cr alloy, comparing with conventionally rolled material. Cold rolling was carried out to 90% thickness reduction and the specimens were subsequently annealed at $700^{\circ}C$ for 30 min to obtain a fully recrystallized microstructure. Cross roll rolling was carried out at a tilted roll mill condition of $5^{\circ}$ from the transverse direction in the RD-TD plane. In order to observe the deformed microstructures of the cold rolled materials, transmission electron microscopy was employed. For annealed materials after rolling, in order to investigate the grain boundary characteristic distributions, an electron back-scattering diffraction technique was applied. Application of cold rolling to the Ni-10Cr alloy contributed to notable grain refinement, and consequently the average grain size was refined from 135 ${\mu}m$ in the initial material to 9.4 and 4.2 ${\mu}m$ in conventionally rolled and cross rolled materials, respectively, thus showing more significantly refined grains in the cross rolled material. This refined grain size led to enhanced mechanical properties such as yield and tensile strengths, with slightly higher values in the cross rolled material. Furthermore, the <111>//ND texture in the CRR material was better developed compared to that of the CR material, which contributed to enhanced mechanical properties and formability.

• 열처리공학회지
• /
• 제31권3호
• /
• pp.126-134
• /
• 2018

In this research, we produced polycrystalline n-type $Bi_2Te_{2.7}Se_{0.3}$ powder using water atomization. To obtain full benefit through water atomized powder, we have implemented spark plasma sintering and hot extrusion for powder compaction. The microstructure and thermoelectric properties were investigated and compared. The average grain size of SPS and extruded bulks were 3.08 and $3.86{\mu}m$ respectively. The extruded material microstructure contains layered grains with less grain boundaries and its counter-part SPS displays dense packed grains with high grain boundaries. Among both bulks, extrusion sample exhibited high power factor (PF) of $2.96{\times}10^{-3}Wm^{-1}K^{-2}$ which is 38% higher than SPS ($2.14{\times}10^{-3}$) bulk sample. Due to variations in grain size and grain boundaries, the SPS bulk shows low thermal conductivity than extruded bulk. However, the extruded bulk sample exhibited a peak ZT of 0.69 at 400 K, which is 19% higher than SPS bulk sample, due to its higher power factor.

• 한국작물학회지
• /
• 제45권4호
• /
• pp.272-275
• /
• 2000

Winter green manure crops including legume increase grain yield of subsequent crop and substitute N fertilizer requirement with organic-No Hairy vetch grows vigorously and can provide N-rich green manure for corn with its soil incorporation after wintering. But, grain yield of corn as succeeding crop would be reduced if its planting time is delayed until late spring. This experiment was carried out to find the proper incorporation time of hairy vetch green manure and planting time of subsequent corn in cropping system with winter hairy vetch(green manure)-summer corn. Hairy vetch was incorporated into soil at a ten-day interval between April 10 and May 10 and corn was planted at 5 days after each hairy vetch incorporation. Soil nitrate concentration on April 10 and 20 in hairy vetch plot was slightly lower than that at winter fallow. Above-ground dry matter and organic-N of hairy vetch increased linearly with delayed hairy vetch incorporation time from April 10 to May 10. Average dry matter and organic-N produced by hairy vetch were 5.7 ton/ha and 248 kgN/ha, respectively. Corn growth and yield decreased as delayed corn planting time after May in spite of increasing dry matter and N-yield of hairy vetch. Nitrogen concentration of corn grain, stalk and whole plant at harvest were the highest in May 5 planting, but total N-uptake of May 5 planting were not different from that of April 25 planting because of lower grain yield. It was concluded that the proper incorporation time of hairy vetch and corn planting time were April 20 and April 25, respectively, because grain yield was the highest and corn could use hairy vetch-N effectively to produce dry matter.

• 한국결정성장학회지
• /
• 제11권3호
• /
• pp.127-131
• /
• 2001

산화물계의 액상소결시 액상량을 변수로 하여 입자형성이 입자성장 거동에 미치는 영향을 고찰하였다. 산화물계 모델로 구형입자의 경우는 MgO$CaMgSiO_{4}$계를 선택하였으며, 각진입자의 경우는 $Al_{2}O_{3}$/ $CaAl_{2}Si_{2}O_{8}$계를 선택하였다. 구형입자인 MgO의 경우 액상량 증가에 따라 입자크기가 감소하였으나,각진입자인 $Al_{2}O_{3}$ 입자의 경우는 계면지배과정에 의해 성장하는 반면, 거친 고상/액상계면을 지닐 것으로 예상되는 구형 MgO입자의 경우는 확산지배과정에 의해 성장하였다.