• 대한기계학회논문집
• /
• 제14권1호
• /
• pp.214-224
• /
• 1990

본 연구에서는 현 저자의 이전의 연구를 확장하여 균일한 열유속을 갖는 2상 기체-고체입자 위 방정식에서 축 방향의 열전달은 반경 방향의 열전달보다 작아 무시 하였으며, 복사 열전달은 기체와 입자 사이의 온도 차이가 적어 무시하였다. 방정식 중 $F_{px}$ 와 $F_{pr}$ 은 2상 사이의 상호작용에 의한 단위부피당 축방향과 반경방향 의 저항력이며, 수직관의 열전달 특성을 부하도와 상대 입자 크기 $d_{p}$/D를 변화시 켜 가면서 조사하는 것이다.다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.420-421
• /
• 2015

Recently construction of new transmission line is getting harder because of social hostility to transmission tower. Howevere, load is converged in metropolitan area and power plants near this area are old and life of generator will end soon. Therefore, power to supply load in this area should be transmitted from east coast area and southern area. For these reasons, securement of transmission capacity without new transmission line construction is important. In this paper, effect of one circuit AC line change to DC transmission at the same transmission tower on the system available transfer capacity is analyzed.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.340-345
• /
• 2008

A computer program, which simulates the parall flow evaporator was developed. The program was having used to simulate the sample $650\;mm{\times}190\;mm$ frontal area, 25 mm flow depth and 3.0 mm fin pitch. It was shown that the cooling capacity of 3kW could be available from the sample. The present model, however, does not consider refrigerant mal-distribution in each pass, which is known to reduce the cooling capacity of the parallel flow heat exchanger.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.59-62
• /
• 2014

Predicting coal combustion by computational fluid dynamics (CFD) requires a combination of complicated flow and reaction models for turbulence, radiation, particle flows, heterogeneous combustion, and gaseous reactions. There are various levels of models available for each of the phenomena, but the use of advanced models are significantly restricted in a large-scale boiler due to the computational costs and the balance of accuracy between adopted models. In this study, the influence of coal devolatilization model and turbulent mixing rate was assessed in CFD for a commercial boiler at 500 MWe capacity. For coal devolatilization, two models were compared: i) a simple model assuming single volatile compound based on proximate analysis and ii) advanced model of FLASHCHAIN with multiple volatile species. It was found out that the influence of the model was observed near the flames but the overall gas temperature and heat transfer rate to the boiler were very similar. The devolatilization rate was found not significant since the difference in near-flame temperature became noticeable when it was multiplied by 10 or 0.1. In contrast, the influence of turbulent mixing rate (constant A in the Magnussen model) was found very large. Considering the heat transfer rate and flame temperature, a value of 1.0 was recommended for the rate constant.

• 설비공학논문집
• /
• 제20권7호
• /
• pp.486-491
• /
• 2008

The performance of a microturbine CHP system equipped with an absorption chiller was analyzed by modeling it. The microturbine with recuperator was simulated with the Brayton cycle model. The mass flow rate and available heat energy of the exhaust gas from the microturbine were simulated. These results were utilized as input values for the generator of the absorption chiller. The absorption chiller is a single-effect air cooled type with a solution heat exchanger. The heat input into the generator was proportional to the heat transfer rate and the UA values of the heat exchangers of the absorption chiller. Furthermore, the COP of the absorption chiller increased with respect to an increase of the heat input into the generator, under the sufficient evaporator capacity condition. When the capacity of the CHP system increased from 30 to 60 kW, the mass flow rate of the LiBr for the absorption chiller doubled, and the UA values for evaporator and condenser increased by factors of x3.9 and x3.4, respectively, under the same COP condition.

• Steel and Composite Structures
• /
• 제37권6호
• /
• pp.741-759
• /
• 2020

Steel plate-concrete composite slabs provide attractive features, such as more effective loading transfer, and more cost-effective stay-in-place forms, thereby enabling engineers to design more high-performance light structures. Although significant studies in the literatures have been directed toward designing and implementing the steel plate-concrete composite beams, there are limited data available for understanding of the composite slabs. To fill this gap, nine the composite slabs with different variables in this study were tested to unveil the impacts of the critical factors on the ultimate strength behavior. The key information of the findings included sample failure modes, crack pattern, and ultimate strength behavior of the composite slabs under either four-point or three-point loading. Test results showed that the failure modes varied from delamination to shear failures under different design factors. Particularly, the shear stud spacing and thicknesses of the concrete slabs significantly affected their ultimate load-carrying capacities. Moreover, an analytical model of the composite slabs was derived for determining their ultimate load-carrying capacity and was well verified by the experimental data. Further extensive parametric study using the proposed analytical methods was conducted for a more comprehensive investigation of those critical factors in their performance. These findings are expected to help engineers to better understand the structural behavior of the steel plate-concrete composite slabs and to ensure reliability of design and performance throughout their service life.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 A
• /
• pp.822-824
• /
• 2005

This paper presents a scheme to solve the congestion problem using phase-shifting transformer(PST) in power systems. Available transfer capability(ATC) is an important indicator of the usable amount of transmission capacity accessible by several parties for commercial trading in power transaction activities. This paper deals with an application of optimization technique for ATC calculation. Sequential quadratic programming(SQP) is used to maximize power flow of tie line subject to security constraints such as voltage magnitude and real power flow. The proposed method is applied to 10 machines 39 buses model systems to show its effectiveness.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.201-202
• /
• 2015

전력계통이 대형화, 복잡화됨에 따라 현재의 전력전송은 한계 전송량에 가깝게 운영되고 있다. 또한 정치적, 경제적, 사회적 수용성 등의 이유로 전력을 융통하기 위한 신규 초고압 송전선로의 건설도 어려운 실정이다. 이 때 루트 송전선로의 탈락은 계통의 과도안정도에 큰 영향을 끼칠 수 있으며, 발전기 탈락을 통하여 계통을 안정화 시킬 수 있다. 하지만 과도한 발전기 탈락은 계통의 신뢰성 있는 운영에 방해물이 될 수 있다. 유연송전기기(FACTS, Flexible AC Transmission Systems)는 이러한 루트 선로 탈락에 따른 발전기 탈락을 최소화 할 수 있다. 본 논문에서는 FACTS의 한 종류인 STATCOM(Static Synchronous Compensator)을 이용하여 사고 시, FACTS 기기 설치 유무에 따른 과도안정도 분석을 진행한다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제12권2호
• /
• pp.25-28
• /
• 2010

A cooldown time is one of the major factors in many cryocooler applications, especially for the design of conduction-cooled superconducting apparatus. The estimation of cooldown seeks the elapsed time to cool thermal object by a cryocooler during initial cooldown process. This procedure includes the dimension of cold mass, heat transfer analysis for cryogenic load and available refrigerating capacity of a cryocooler. This method is applied to the specific cooling system for a 3 Tesla superconducting magnet cooled by a two-stage GM cryocooler. The result is compared with that of experiment, showing that the results of proposed method have a good agreement with experiments during initial cooling of superconducting magnet.

• 대한환경공학회지
• /
• 제30권12호
• /
• pp.1218-1224
• /
• 2008

본 연구는 yeast의 한 종류인 Candida tropicalis 배양액을 유동상 반응기 형태로 운전하여 대표적인 휘발성유기화합물인 톨루엔의 제거효율을 향상시키기 위해 수행되었으며, 톨루엔 흡착과 물질전달 능력을 동시에 향상시키기 위해서 생물반응기의 유동상 물질로는 입상활성탄(GAC)을 사용하였다. 효모를 적용한 GAC 유동상반응기는 유입 톨루엔 부하 13.1$\sim$37.4 g/m$^3$-hr 범위에서 50$\sim$80%의 처리효율을 나타내었다. 또한 톨루엔 유입부하 291 g/m$^3$-hr 조건에서 최대분해능 172 g/m$^3$-hr을 얻어, 본 연구의 GAC 유동상반응기가 안정적이면서도 높은 처리효율을 나타낼 수 있음을 확인하였다. 충격부하 실험에서는 유입농도의 갑작스런 변화에도 일정하게 처리효율을 유지함으로써, 유입농도의 변화에도 안정적인 반응기 운전이 가능하다는 것을 알 수 있다. 최대분해능실험 결과 유입농도가 2배 이상 증가하였으나 처리효율은 일정하게 유지되었으며, 유입된 톨루엔이 GAC에 먼저 흡착된 후 천천히 탈착되어 효모에 의해 분해됨을 확인하였다. 따라서 유동상으로 투입된 GAC가 톨루엔의 물질전달을 향상시켜 미생물반응기의 전체 처리효율을 증가시켰다.